DKD Display Wiring DIY E Bike

Подписаться 6 тыс.

Просмотров 15 тыс.

50% 1

I was having issues with the DKD e bike display. I dont know how I couldnt figure out how to wire it. Its so easy. At first I was using an external battery for testing and it wouldnt connect to the controller. Its really important to use the same power that is going to the controller so it can sync to the speedo wire.
Feeling generous? Buy me a coffee to help support my videos.
www.buymeacoff...
Thanks for watching and check out the Derbi Build playlist.
• Derbi RM85 Dirt Ped St...
#QS138 #ebike #cornped
My Gear Links
Main Camera amzn.to/3qw1Cnt
Main Lens amzn.to/3qsSOPf
Wide Lens amzn.to/3pwmOdQ
Portrait lens amzn.to/32ooNbv
Mic amzn.to/3HgkBch
Light amzn.to/3qw2SXJ
360 Camera amzn.to/3euCkjV
Selfie stick amzn.to/3pxJGJK

Опубликовано:

16 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 33

@csitambo9893 9 месяцев назад

Please man DO NOT put down this videos never! 😂 I’am building a pitbike with a votol em80sgpt(whatever) and these videos helps me sooo much! You are my hero in there days! Thanks, you are a champ!

@Corn-ped 9 месяцев назад

awesome to hear! Keep up the bike build!

@DKLVE Год назад

Excellent video. I can finally use the display. Like you say it was pretty simple but the wiring harness included is so complicated. Thanks a lot

@Corn-ped Год назад

Awesome! Glad it helped

@santa16158 Год назад

life saver. Thank you sir!

@Corn-ped Год назад

Awesome to help!

@jositojosito9124 Год назад

Nice video ,please what is the communication protocol does this display uses ,UART or I2C ,or something else ? Because i see only a one wire for communication which is in your case blue/withe ,please make things clear for me , because i want to start repair business ebike and scooter ,im learning some repair info ,and the CAN BUS is for the battery u said ,whatsthe purpose to connect these 2 CAS BUS wire to the battery ,thank u in advance

@ryanmerrill8879 8 месяцев назад

Can bus is a communication protcol. It for more than just bms to displays. Its used in automobiles to have the deferent devices communicate with each other. Many controllers also use Canbus, The two canbus wires are for send and receive (RX and TX). Communication protocols can differ depending on manufacturer.

@miniordie 9 месяцев назад

Thanks for the video! As I’m waiting for my 205 hub motor and 150 controller thought I’d ask. After we connect the 3 wires to the speedo, does it accurately display battery percentage, speed and d whatever else? I’d assume it just pulls the info from the controller? Did you have to use the back two buttons for anything? Thanks so much!

@Corn-ped 9 месяцев назад

yeah. After connecting it, it displays battery correctly. I did have to use the back to buttons to calibrate the speedo. I set it according to my tire circumference to get the speedo close and then I rode around with a GPS and dialed it in.

@ratzona1 3 месяца назад

Hi.. I have a question.. I have the same screen connected to em100 With 72v battery ..the speed shown on screen is extremely higher than the quad drives , is it fixable?

@Mauipat 7 месяцев назад

I have a Question about the display voltage. You said it was 72 volt going into the display, but my lights and horn are 12 volts, does that 12 volts come out of the display or is that supplied by the 12 volt inverter? any thoought on that is greatly appreciated.

@brendonfriesen8327 7 месяцев назад

Thanks for this video! Any reason why after hooking it up my display just randomly flashes with different readings of speed and amperage while stationary?

@paucarneado487 6 месяцев назад

Help me with this question please! The speed sensor you use (the white cable) , does it has to be installed or it's just one of the phases cable. My controller doesn't have that speed sensor cable, that means I can't install a screen?

@Corn-ped 6 месяцев назад

you could still install using the CAN cables.

@chrislucas357 6 месяцев назад

What/ where is the white wire you are getting the speed sensor from??

@ManMan-b5y5c 8 месяцев назад

Have a controler but it has no 5pin display connector but there are several other wires 3pin would I be able to use any of those

@JB360_NYC Год назад

Great video! For some reason the dkd display I received didn't have the 2 buttons on the back. I'm not even sure how I'm going to be able to adjust to mph 😕

@Corn-ped Год назад

Oh thats strange. is there anything on it? there has to be some way to program it.

@JB360_NYC Год назад

@@Corn-ped did all the 3 wire connections (battery positive, battery negative, speedo line) and still no power to the display. Tried it on another Fardriver bike and still nothing 😢

@Corn-ped Год назад

@@JB360_NYC they use to be 12v and the new ones are 48v-96v. What voltage are you trying to power it with?

@JB360_NYC Год назад

@@Corn-ped 72V via the battery. If that's true regarding the newer ones than I may try the step down route.

@Corn-ped Год назад

Yeah. I would try 12v.