DME Arc Procedure 

I managed to grasp the procedure couple of days before my interview and it helped me fly the dme arc accurately in the sim session for my interview which I managed to pass. Thank you buddy. Your procedure helped since it was so easy to understand. I just wrote down the - and + and took it with me to sim. And followed the procedure and established on ILS. Thank you sooo sooo much again

Thank you very much. Finally understood. Taking my Checkride 1 week later

Umetisha sana 🔥🔥🔥👊

Nice explanation bhaiya...... Be there with us always. Love you Bhaiya. Regards

Good explanation. Thank you for the video.

Amazing bhai

Very well explained

This procedure was making me mad in pursuit of trying to understand it. Your video helped me so much. I am very thankful to you. Your awesome. If you could please add details about how to set this type on g1000 glass cockpit. I would appreciate it.

Really good effect...but have one doubt...I went for my oral exam already... The question raised by dgca why +100 -100 +80 -80.... Any particular formula or procedures behind that

Dear pilot hi, first of all I am thankful for your video, then I want to ask you about O/B L

Great explanation but there is a much easier way to fly DME arcs. Inbound, center the CDI on the VOR head to determine where you are. In your Inbound right turn example, it would be the 200 degree radial. Find where you want to go on the VOR head. In the same example it is the 090 radial. How do you get there? Go to the reciprocal of where you want to go, 270 (270 is the reciprocal of 90). In your example 270 is an initial left turn with an arc to the right. What heading do I turn to? Since your initial turn is to the left, to arc right, just look at the 270 degree index on the VOR head, it's 290. Turn to that heading at your 1% of true airspeed. Then just turn ten twist ten. Done. You can figure out any arc in about 4 seconds this way. For outbounds, the only difference is the "where am I?". Instead of it being at the bottom of the centered CDI, it's at the top.

Turn 10 Twist 10 from VOR or NDB

If you could add a bit about how to make an arc using RMI needle, it will complete this video. Also, what's the maximum & minimum speed to be maintained in dme arc for each category of aircraft in different airspaces ? Thanks in advance :)

And yeah bro thank you it was very helpful :)

Hello, thanks for the useful video!! It really helped me to visualize DME ARC, I have a little question, So course for inbound, seem to be bearing not radial. Is that right?

Thanks you save my life sir

Hai ! Can u explain adf,NDBs, Vor

that’s it!. thank you.

Dude you're awesome!

Good video! Please explain when should I make a final to landing course? In practice we use 30 degrees before final course (at 160 kts). But what about crosswind approach? Does you have any formula for calculating time to make a turn? Thank you.

Why you didn't apply wind considerations on the DME Arcs? That would've made clear that TRK is more important than HDG in the end.

Can u explain holding patterns and entry.thanx.

Hi thank you for this :) What if the dme arc is from inbound to outbound, and vise versa, using HSI only?

After turning 90 degrees to join the arc, afterward why can't you just watch for DME distance, if the DME distance is increasing, meaning you are flying away from the arc so you better start turn towards inside a bit vice versa or even easier way keep your VOR always 90 degree of your current heading eh . wouldn't this work out better ?

I'm having a hard time understanding where the head and the tail of the needle goes on an HSI. If you want to intercept a 356 course inbound to a VOR starting at an IAF 15.3 DME on a 095 radial from the VOR, do you put the head of the needle on 285 during your first twist? Seems you would since you want to end up flying an inbound bearing and would use a reciprocal of the IAF radial.

Bro on the outbound example on the heading you went up by 100 but on the second outbound you went only by 10. Please explain.

R u sandesh

Can u make video on ndb intercept and approach :)

is it same for any dme arc value?

Thanks, but there's no more ink in your pen, I cannot read your writing Sir.

hey, bro can you make a series like from absolute zero to a professional?

crack

Use darker markers can’t read what you are writing

Cannot understand his accent