Dodge Ram 2008 6.7L G56 Transmission Clutch Installation 

Buddy thank you so much for this video of course I took way longer than you but yhou saved me a ton of money. Thank you so much again God bless!!!!

Thank you great video, we are doing this on a 07 dodge 3500 dually this weekend and we do not have a auto lift we are doing it caveman style on the concrete floor, wish me luck.

best videos on clutch job, mahalo.

Good dissection of the old clutch.

Thank you for posting this video. We just bought a clutch kit K52179-1SK from O'Reilly's, however, the box was open. Looks like all the parts are there EXCEPT the installation guide, which from your video looks indispensable. Will call Perfection in the morning to see if you can fax or email me a copy of the installation guide. I think we could do it from this video alone, but I would rather have the guide for backup. Also, I didn't see the spline lubricant in the box we received. Blessings, looks like a great product!

Damn great video you are the man I like the how’s and why’s. Great detail

I wish I had gone with one of your clutches. The factory one went out and I replaced it with one ordered from Missouri. Not pleased at all. Looks like your product is of good quality. My next clutch will be from you guys. Would love for you to install it.

That throwout bearing noise about made me have a stroke.

You didn't mention the gear rollover noise that the G-56 will now produce. That is the side effect of the smf conversion. it the guy worked the trans over 99K I wonder why he didn't go with the stocker again? I miss that nearly silent trans. I have the SBC OKHD conversion clutch in mine with Amsoil MTG 75-90 synthetic.

Like your other videos ...GREAT JOB.....

Couple questions. Number 1: if the clutch is not self adjusting how do you adjust for wear over time? How do you know when to adjust? Number 2: how did you align the holes when you put the unit back in? showed bolting the tray back to the motor how about the clutch to the flywheel? Did you use the special tool again to turn the motor and just spin the trans by hand? Number 3: visited 3 local shops and both book this at almost 10 hours. after watching your video it makes me wonder, "where is the other 8 hours going"? what do you guys book the time for labor on a project like this?

Thanks this was great

what's the power rating on this system I've done a lot of after market and my factory clutch just slips if I don't ease up to speed if I put the pedal down in any gear below 1800 rpm just makes lot of noise and goes no where

Is this available for 2010 Ram 3500 with the G56? My 5th started to slip. If yes where can i buy the parts?

Nice video. Same on a 2016?

So the flywheel and clutch are a single unit? I've ordered this part from Rock Auto and am hopefully put it in this weekend. I didn't see you use the alignment tool at all. Was that just off camera?

man looks like a tuff job

hi, whats the difference between dual mass flywheel and solid flywheel? need to replace mine but i dont know what is the best!! mine now is original!!

I am also doing a clutch install on 6.7 cummins with g56 transmission. I need the bolt torque for the bolts connection the transmission to the engine. Also would like the tightening pattern. Thanks.

I just put the valair 700 hp clutch in with ceramic buttons. having trouble adjusting the clutch with the neutral safety switch any ideas also for reference how much is your kit and were can some one go to get it thanks again buddy.

What was the total time to do the swap?

did you remove the transfer case or just both drive shafts?

How much for the kit ? And website ? Please thanks

to bad you didnt supply a rear main seal and installer with each kit

Hey I have a 08 dodge 6.7 6speed manual . The south bend clutch I have is good but noisy . Lol any way my hydraulic clutch went after 40000 miles is the install the same as ur vid on the 2005 2500 ram ?

what is the easiest way to get to the top bell housing bolt without taking the exhaust off

Grease on the teeth or spline is not a good idea, you just fling it off. if you want to use something use graphite.

I have a 07 Dodge Ram 3500 5.9 diesel 6 speed manual and I have a hard time shifting into gears when it's at a stop mostly when I want to go into reverse I got the master and slave cylinder replace and still does the same thing what could be wrong with it??

Hey bud..Where can I purchase a baring tool..My Kit only came with a clutch alignment tool!!Is there a part number on it?

Were can you buy the baring tool ?

Just installed this exact same clutch on my 06 I noticed after install truck is harder to go into the gears and pedal is stiffer not as soft as the dual mass any suggestions

where can i get your product??

what kit number is this?

G56 garbage don't by that transmission and to all those engineers out there stop building your transmissions casing out of aluminum i guess they don't know nothing about distortion in metal...pure junk folks heavy duty truck with an outer aluminum casing so brilliant

i have 300 thousand miles on my truck, put in a new clutch and the pedal doesnt engage until about an inch from the floor and hard to get in gear. any suggestions, everything is new hydraulics, throwout, flywheel conversion, ect..