Тёмный

Does your motorcycle stop when you put a gear? How to check and replace the kickstand sensor. 

El garaje de José Manuel H
Подписаться 75 тыс.
Просмотров 7 тыс.
50% 1

In this video I show you step by step how to verify, and if necessary, repair or replace the sensor or switch of the kickstand of a motorcycle. The most characteristic symptom of this fault is when, with the engine running and the goat stop removed, a gear is engaged and the engine stops. Or the opposite case, when with the engine running, and the kickstand on, when a gear is engaged the engine does not stop.
In the example of this video it is done on a HYOSUNG GV 650 AQUILA from 2006.
It belongs to a series of videos that show the complete process of disassembly / removal of the engine of the Hyosung GV Aquila 650 2007 carburetion model, and the rest of the components until leaving exclusively the chassis for the restoration of all its components and subsequent assembly.
Hyosung Aquila 650 Workshop Manual Video Playlist:
• 36 HYOSUNG GV AQUILA 6...
Playlist of videos of Pierre's teachings on Hyosung 650 engine repair:
• Novedades del canal. D...
Links to individual videos from the Hyosung Aquila 650 Workshop Manual Video Series:
1. Removing seat and fuel tank.
• Hyosung 650 GV Aquila....
2. Removing cowling and battery.
• Hyosung GV Aquila 650....
3. Removing the radiator.
• Hyosung 650 GV Aquila....
4. Removing air filter box.
• Hyosung 650 GV Aquila....
5. Removing the carburetors.
• Hyosung 650 GV Aquila....
6. Removing the exhaust line.
• Hyosung 650 GV Aquila....
7. Previous electrical disconnections to remove the motor.
• Hyosung 650 GV Aquila....
8. Removing the drive belt.
• Hyosung 650 GV Aquila....
9. Drain engine oil.
• Hyosung 650 GV Aquila....
16. Removing front wheel, fork and handlebar.
• Hyosung 650 GV Aquila....
17. Valve clearance Hyosung Aquila 650 with Pierre.
• 12. Reglaje de válvula...
18. How to install the engine of the Hyosung Aquila 650. Part 1 of 3. Anchoring it to the chassis.
• 15. Cómo instalar el m...
19. How to install the Hyosung Aquila 650 engine. Part 2 of 3. Transmission, carburetors. radiator.
• 16. Cómo instalar el m...
20. How to install Hyosung Aquila 650 engine. Part 3 of 3. Oils, filters, liquids and brakes.
• 17. Cómo instalar moto...
21. Replacing the front fork oil and liquid front brakes.
• 18. HYOSUNG aquila 650...
22. First problems in its start-up after repairing the engine. Part 1.
• 19. Hyosung 650 Aquila...
23. First problems in its start-up after repairing the engine. Part 2.
• 20. Hyosung 650 Aquila...
24. The speedometer does not work for me. How to check speed sensor. HYOSUNG 650, 250.
• 21. El velocímetro no ...
25. The speedometer does not work for me. Verify and repair your wiring. HYOSUNG 650.
• 22. El velocímetro no ...
26. How to check the start button and the clutch lever system to start.
• 25. Cómo verificar el ...
27. How to rebuild the Hyosung 650 engine with Pierre. Part 2 of 5. Gearbox and lots of talk..
• Como reconstruir el mo...
28. How the motorcycle gearbox works. Rebuilding Hyosung 650 engine. Part 3 of 5.
• Cómo funciona la caja ...
29. How to rebuild the Hyosung 650 engine with Pierre. Part 4 of 5. Joining semi-carts.
• Como reconstruir el mo...
30. How to rebuild the Hyosung 650 engine with Pierre. Part 5 of 5. Arming clutch system.
• Como reconstruir el mo...
31. How to replace the oil engine and filter.
• Hyosung Aquila 650: Có...
32. How to replace the coolant and bleed air from the circuit.
• Hyosung Aquila 650: Có...
33. How to replace the air filter.
• Hyosung Aquila 650. Có...
34. The gas tank cap on my motorcycle won't open, it's locked and I have the key. SOLUTION!
• La tapa del depósito d...
35. My motorcycle won't start. Why?
• Mi moto no arranca ¿Po...
36. How to clean the fuel filter of the HYOSUNG Aquila GV 650 and fuel loss due to macaron.
• Como limpiar el filtro...
37. If your motorcycle's exhaust turns LIVE RED (incandescent) don't miss this video.
• Si el escape de tu mot...
38. How to do the HYOSUNG 650 cylinder leakage test and valve clearance measurement.
• Cómo hacer la prueba d...
39. How to synchronize the carburettors of the HYOSUNG 650.
• Cómo sincronizar los c...
40. How to repair, disassemble and maintain the fuel tap on your vacuum powered motorcycle.
• Cómo reparar, desarmar...
42. With the last touches of the HYOSUNG AQUILA GV 650. Front suspension and brakes.
• Con los últimos retoqu...
43. How to put a new Amazon fuel tap on the Hyosung 650 (GT-R and AQUILA).
• Cómo poner un grifo de...
44. HYOSUNG GV 650 Aquila. Review and test ON BOARD. My personal impressions.
• 26. HYOSUNG GV 650 Aqu...
45. Does your motorcycle stop when you put a gear? How to check and replace the kickstand sensor.
• ¿Tu moto se para cuand...

Опубликовано:

 

2 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 20   
@sickle40
@sickle40 2 месяца назад
Muchas gracias por tu ayuda saludos desde Chile
@ElgarajedeJoseManuelH
@ElgarajedeJoseManuelH 2 месяца назад
Gracias a ti por comentar. Un saludo.
@heribertomartinezarboleda7720
@heribertomartinezarboleda7720 2 года назад
Muchas gracias por la explicación, más claro no canta un gallo.
@ElgarajedeJoseManuelH
@ElgarajedeJoseManuelH 2 года назад
Gracias a ti por el comentario. Un saludo.
@xeylldrex9784
@xeylldrex9784 Год назад
Y si , meto marcha dejo la pata y la moto no se para y mudgo desconecto el sensor ( no esta puenteado ) y arranco meto primera y no se cala , qje podria ser el problema?
@ElgarajedeJoseManuelH
@ElgarajedeJoseManuelH Год назад
Pues que el sensor de la pata de cabra o su cableado está averiado. Un saludo.
@JuanGarcia-vz7ns
@JuanGarcia-vz7ns 11 месяцев назад
Tengo una vulcan 800 classic y hace lo mismo y se apaga la moto a la hora de meter la velocidad
@ElgarajedeJoseManuelH
@ElgarajedeJoseManuelH 10 месяцев назад
Pues ya sabes lo que puedes ir comprobando. Un saludo y gracias por comentar.
@alexanderkilin5922
@alexanderkilin5922 Год назад
Hola, tengo un problema con el carburador Hyosung GV 650. la moto tiene un problema al circular a una velocidad de 120/130 km/h uniformemente. Después de aproximadamente 1 minuto, el motor comienza a tartamudear como si no estuviera recibiendo combustible o chispa. Arranque en frío ok, hasta 100 km/h todo bien. a 120 y más rápido hay un problema. Bobinas de encendido nuevas, bujías nuevas, todos los filtros nuevos, carburadores también cambiados, mismo problema. tienes idea de que puede ser. estare agradecido por cualquier ayuda
@ElgarajedeJoseManuelH
@ElgarajedeJoseManuelH Год назад
Pues pueden ser varias cosas pero yo apostaría a que esta a punto de morir el pistón delantero. Estas motos con bastante frecuencia gripan el conjunto pistón cilindro delantero. Mídele la compresión de los dos cilindros o haz la prueba de fuga de los cilindros y a lo mejor por ahí te aparece la avería. Un saludo.
@alexanderkilin5922
@alexanderkilin5922 Год назад
Gracias por la rápida respuesta, aún no he medido la compresión. pero ayer noté que el cilindro trasero fallaba, así que resincronicé el carburador y mejoró, pero no al 100%. Si tiras del cable por atrás, el cilindro delantero funciona bastante bien por sí solo. Si tira del cable en la parte delantera, el motor funciona al ralentí, si aumenta la velocidad, los cilindros traseros también funcionan. Durante un arranque en frío, el colector de escape del cilindro delantero se calienta unos 3 segundos más rápido que el del cilindro trasero. Compresión que mediré los días.
@ElgarajedeJoseManuelH
@ElgarajedeJoseManuelH Год назад
Yo creo que nada de eso es significativo como para descartar o no problemas en el estado de salud del cilindro pistón con los síntomas que describías antes. Un saludo.
@alexanderkilin5922
@alexanderkilin5922 Год назад
​@@ElgarajedeJoseManuelHHola amigo, hoy medí la compresión y encontré que la siguiente es de 9 bar en la parte delantera y 10 bar en la parte trasera. ¿Están bien los valores?
@Kherzur
@Kherzur Год назад
La mia lo hace sin soltar el embrague... alguna idea?
@danielvargas3886
@danielvargas3886 10 месяцев назад
hey, estoy en las mismas, aqui buscando alguna posible solucion. hasta ahora lo que se; el aceite aun esta muy frio y hay que dejar que caliente para que el clutch se despegue bien. PERO si has encontrado una solucion porfavor cuentame.
@Kherzur
@Kherzur 10 месяцев назад
@@danielvargas3886 en mi caso fue el muelle de la pata de cabra
@21unicul
@21unicul Год назад
Muy buen video y bien explicado saludos.
@ElgarajedeJoseManuelH
@ElgarajedeJoseManuelH Год назад
Gracias por el comentario Jon. Un saludo.
@juanculpian1800
@juanculpian1800 Год назад
Hola Jose Manuel! Tengo una aquila 650 gv inyeccion, y lo q m pasa s q kuando voy n marcha y voy reducciendo al yegar a primera, se m para la moto. Al ver tu video y echar un vistazo a mi moto, he visto q tiene el suich, pero no tiene el embolo del sensor. No se si sto s la kausa o es d embrague, por que si es verdad q m kuesta en kaliente enkontrar el neutro. Un saludo
@ElgarajedeJoseManuelH
@ElgarajedeJoseManuelH Год назад
No creo que tenga que ver con eso. Un saludo.
Далее
Sensor pata de cabra R1200 BMW
15:54
Просмотров 37 тыс.
Como cambiar retenes de Suspensión invertida
13:40
Просмотров 147 тыс.
Sustitución sensor pata de cabra Keeway RKV 125
8:33
Просмотров 1,1 тыс.