I think you've found the right balance with your editing, information and entertainment. This was one of my favourite of yours to watch so far. Fantastic! Looking forward to the next one. 💯
This looks great! I love that it has two different lifts. My best tip for lining up the tops (if double-sided tape or painter's tape and CA glue don't work as people have previously mentioned) is to use a piece of paper. Line it up exactly where the top will be, use a pencil to mark the holes, then flip that over to the bottom side of the box top and line up the corner of the paper with the corner of the top. I've used this trick a few times, both using the pencil to do a rubbing to get the locations of the holes, or just poke a hole in the paper where the holes are. My dad used to use graphite powder also to cover the bracket and put the top down transferring the graphite to the bottom of the board. The only problem with that is if you don't get the board set down exactly in the right spot or the bracket is just a hair too low, it won't transfer, but I've used that trick to and in the right cases, it works perfectly!
I would use a transfer screw set, or something similar to mark the holes for the lift mechanism. You could make your own by cutting down some screws, or sharpening some short bolts to a point. Look up transfer screws for the general idea of how they work, and with some creativity you could use the same principal here.
I used blue painters tape on the table top and on the lift hardware with super glue between them. I then marked all the holes with a pencil, then removed the top and pre drilled on the marks. I put the table top back on the lift hardware and secured it with screws.
A trick to line up a top with the brackets in a situation like this is to use some 3M command strips. Line it up, press it in place, and if you use enough strips, you can lift the top up with the brackets attached. Adjust the hole position very slightly to account for the height of the command strip. Depending on the lift mechanism, it is sometimes easier to remove the gas assist.
Thank you so much for this beautiful design. My girlfriend and I both work from home and our new coffee table is perfect for us! I used double sided tape on the top of the hinges (Alien tape) and it was just strong enough to lift the table tops and then it was easy to drill the holes, remove the tape and screw the top.The result was perfect on the first try and it didn’t remove any of the finish. I’m not promoting this particular tape at all I’m just happy I finally found a use for it! Thanks again for your video and plans you are a great teacher and very talented!
Great build! I thought of a trick for mount for the folding hardware. Start by supporting the mounting plates with two scraps so that it is level with the top surface, then use two sided tape to temporarily lay on the top. Afterwards fold out the top to drill the holes and mount the screws.
The finger holds is a nice touch, nice job on the build! Definitely can be built without expensive tools. Keep up the great work as the goal is for us to continue to inspire others to build something awesome! 👍🏼
I use paint sometimes to transfer marks. Cover the bracket in paint around the holes and carefully set the top in place. Flip it over and mark the holes with an awl, then wipe off the paint before it has a chance to soak in
I was just telling someone the other day that I wanted to build a table exactly like this, but had no idea where to start. Then this video showed up today in my feed. Excellent job. I'm no subscribed and will watch some of your other videos. Thanks.
Really do love this design - perfect setup for a sofa like yours! The mid video add was actually a Disney + ad...they must have watched the beginning haha
What's the trick for getting a good finish in the areas where you have glue squeezeout? Doesn't the glue fill the pores of the wood and prevent stain/poly from looking right in those areas?
Another great video and project, Alex! I love the double lift and I know you mentioned wanting better selection for the walnut, but I really like how the top turned out!
As always, another great video! For the top installation, i would first install it like how you did, mark its actual size, then take it out to carefully trim to size. After that you already have the correct screw holes to reinstall.
To mark the hole exactly to align the brackets to the table top squeeze a piece of cotton ball in to the holes and drop some ink on it. Lay the table top on top and there you have the perfect mark on your table top.
@@rajathygerlynhenry8931 I have not unfortunately. My friends shop got flooded at the end of the summer and he’s been rebuilding and getting things back in order. Once everything is up and running, I will definitely be!
Maybe this was mentioned, I didn't read ALL the comments. I think you could save some alignment headaches with the lift-top mechanisms by changing the order of assembly a little. Leave the bottom out of the table until you have the top secured in place. This way you could just flip the table over and work on it from underneath.
Great build! I had the same problem lining the hinge mechanism and ended up referencing the holes like you have. Initially I used sharpened bolts through the holes to press the top down to get the position for the holes. Unfortunately I didn’t have the right size nuts so I had to use tape to hold the bolts in place which didn’t work real well.
Great video and build Alex! I wonder if you could have done a clamped up dry fit without the bottom in place and then with the carcass upside down drilled the holes for the lift hardware?
Great build as always. Looking forward to the next one maybe with more angles, hehe. The queue of stuff I want to build gets longer every time I watch your videos. Your shop looking good too.
I love this table , was wondering if hot glue on the brackets would be a good idea to have a temporary fix while you drill the holes, you have enough play at the beginning to use spacers and placing it , and at the end hot is easy to take off (only prob you might have some light sanding to do underneath but you would get perfect holes I think, just an idea , thank you for the plans !!
Maybe I’ll try it next time. These things are kind of like soft close drawers that take some force to pull open. But the tops are much heavier than drawer fronts, so it’s got gravity and weight working against it too haha. But CA glue might be the answer! Thanks!
@@BevelishCreations yeah for sure. Not simple.... I've never worked with this type of hinge before. But is it possible to adjust the tension on them temporarily? So its easier to open? Then once it's assembled you can tighten it back up?
8:00 Solution: Carpet Tape. Bourbonmoth I think his show is called does this. Used this for something else and it worked. But maybe someone already said this. 😂
Design the build of the table where the bottom panel can be left out. Then you can flip it over, lay it on the top and affix the mechanism through the bottom.
Very well done on video. I would add more time to the reveal. It is the payoff and everyone, not just yours, just breezes by the final. Make the ending more like Return of the KIng.
I’m new to woodworking and have only built “shop grade” furniture in the past. I would like to start sourcing materials for this project but I’m having trouble procuring the 1/8” x 3/4” x 50” walnut edge banding. Where could I find walnut in 50” lengths?
Hi, the “edge banding” I used was just walnut lumber I cut to 1/8” thick strips. You can get lumber from woodworking stores like Rockler or Woodcraft, or other lumberyards. You can join Facebook groups and ask people who live in your area for recommendations
Great build! I have this exact same issue and I have been thinking about building a table like this. If I did not want the cubbyhole but just the whole long top to lift up, would it work the same or do I need a different lift mechanism?
Please forgive my ignorance, still kind of a newb ;) ... at about 3:10 you're cutting the grooves for the pieces to lay in. Using a "dados?" ... is that just a router that you're suing a special name for... or is the dados thing the straight line you're using to make sure you don't mess up the straight line. This looks like a build that's just challenging enough for me, and I have a sheet or two of better quality plywood in the garage that just might make this something I can take on this summer... just want to make sure I have my ducks in a row first ;)
@@BevelishCreations I’m not knocking you for having nice tools. More power to you. Obviously, I wish I had those. You just make yourself look like a fool, if you call them “cheap” or “basic”.
No I get it. I was just talking about the dowel jig. Because I usually build with the Domino before this. It’s been over a year since I built this, and I use this cheap dowel jig more than the domino