Dual Turntable Cable Replacement Dual 701, 704, 721, 1209, 1219, 1229 etc. 

Thank you. Swapped out Din lead for RCA leads (supplied by yourself) replaced the Steuerpimpel and changed the cartridge and attached a new head shell (supplied by you). Now my Dual 621 is working perfectly and sounds amazing

You just helped me to fix my CS701 with molten power supply. Giving up on the original unit, I went for a plain 12V DC supply (LED-string type). Missing the stroboscope and havin to adjust speed, but otherwise fine. Thanks a lot for your very helpful video!!!

Nice video! Very clear dialogue. I have a Dual 721 that I pulled out of a trash pile! it has a few bent parts and needs a stylus but the motor runs.

In case you’re here with a Dual 502, it only needs standard rca cables (males on each end). They plug right in, internally, just like they connect to your receiver.

Thank you! I replaced the RCA cables on my CS 505-2 and this video pointed me in the right direction. Details are different; the internal connection and the cable protector was hard to remove.

Shure V15 type III and dual 721, my setup exactly.

Thank you for the video. It was very helpful.

You have to cut the ground bridges, when you change to cinch with both ground connections.

at start, also remove the counterweight, specially for the 701/704/721 the CW it is a fragile part ....

Muy agradecido por tu video ..yo me compre una dual 1225..sonaba genial ..pero el cable rca estaba malogrado ..lo cambié y ahora suena un ruido parasitó que no se de donde viene ..no se si debí haberle cambiado el cable

Nice thorough Video on this TT - which I have. But you don't show the new Cable ? What kind did you use to replace the RCA Cable ?

Replaced RCA cable and am getting constant low-level hum. (Old cable was intermittent hum, sounded like broken wires inside the cable; you could adjust cable and stop the hum). CS 1268.

What about the Grounding?

Forgive me, But I don't see how you replaced the Line Out Wire RCA cables? I have a CS 5000 model with a RCA connector that has fouled. The connection to the Preamp (NAD 1300) is creating HUM - severe HUM. I wasted money by having the NAD Preamp in a stereo repair shop which replaced a number of burned out diodes. he showed me the burned out ones. When I brought it home, I had HUM again. Then I returned the NAD to the shop. He had the NAD in his shop connected to a TT in the shop for 48 hours - running non stop , No HUM. After returning home, and playing the TT for awhile, the HUM returned. I found that if I jiggled the RCA cables for the TT to the NAD preamp, the HUM was eliminated !! Yes, It is grounded (I redid the ground checked 2X) . So, the culprit is the faulty RCA cable form the Dual TT. I am hesitant to do what is described here - taking the entire TT apart ? Is it a good fix to get new RCA connectors (Soldering kind )? THX for your video description.

i realy liked your video! It really helped me open up my old dual 701. I was wondering if you know if there is fuse in there somewhere Cus mine doesn't seem to get any power right now

Why am I replacing and with what. Just asking..🤔

do you know where I can order the rca to those snap connections that appear in the bottom left picture of this youtube video?

Hallo. I have a dual cs5000 that have bad phono plugs. Can i change the cable the same Way on that, you Think.

Hello, I have the dual 1241 I'm having an issue where the unit worked great but now all of a sudden I'm getting nothing from the left side of rca is this a cable issue or is there a bigger internal issue with this unit that needs repair or replacement?

Greetings, I have 704 model, I had it refurbished, but now I have a problem that the left channel is about 5 db lower than the right one, at first I thought it's amplifier, but after some experimentation it turned out it is the turntable. Tonearm, stylus, antiskate etc. is set up properly, do you have any ideas what could it be? Do you think that any contacts might be oxidized?

Very helpful.

My 721 has RCA jacks on the bottom already. Was this done as an upgrade by Dual at some point or did someone else do it?

Where can I get this cable??!!

Hello! Its fit to 741Q?🤔

Hi good day. I have the same model but I have a problem, blow the fuses. Could you help me to make the correct connection for 110v on AC. since he comes from europe and i live in mexico. greetings and great channel.

Hello. I have a 1225 HS141. when I place on "ON" the capacitor 0.047 µF 250 V burns. Thanks for your advices. (Google translation)

Hi my 1019 after finishing the record the tone arm goes back but not going to rest, and then goes back to re start playing again. Any suggestions? Thanks.

Does this also work for DUAL 601?

You should get a mount for your phone

Im replace only din on cinch 🤷