EBikeKit Pedal-Assist Sensor Installation

Подписаться 1,7 тыс.

Просмотров 50 тыс.

50% 1

Note, the light function is reversed now - when there is no magnet nearby, the light will be off. When a magnet passes by in the correct direction, the light will flash on one time.
see this video:
• E-BikeKit | PAS Lights...
We're available Monday through Friday 9am-6pm EST via phone at 866-894-4620 and can be can also be reached anytime by sending an email to support@ebikekit.com.
For more information on E-BikeKit, be sure to check out our website, www.ebikekit.com
Electric Bike Technologies, LLC
Phone: +1 888-220-6736
Email: info@electricbiketech.com
Website: www.electricbiketech.com

Спорт

Опубликовано:

5 апр 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 36

@curiouspenguin6887 Год назад

Finally! Somebody films this step from a USEFUL angle!

@drisaglam 6 лет назад

Crystal clear explanation! Bravo!

@kenatkinson681 6 лет назад

You need to tighten the zip ties first before cutting the ends off

@rhysprobyn4546 2 года назад

Clear and concise, many thanks for sharing.

@longrider42 4 года назад

I ride a two wheeled recumbent bike. I had to take the pivot off the sensor so it would fit on the frame and under the ring. I also hot glued the magnetic ring to the inside of the left crank arm too hold it in place. But, you guys don't seem to think about putting these on two wheeled recumbent bikes. I've a bit over 450 miles down and all is working just fine. Just wish you guys sold a 48 Volt 15 Amp battery.

@mekatrol 4 года назад

Thanks heaps for doing this video.

@alireza071 4 года назад

Hi is this sensor works with all model controller with pedal assist or just certain controller?

@binarumah 7 лет назад

good sharing.thanks

@difrancescoa 5 лет назад

so if the led is not working (not blinking nor steady) it means I have a connection problem, right?

@eightwheels Год назад

Do you have any tips on fastening the magnet ring more securely? On my Sun Baja trike it moves much too easily and has to be constantly readjusted to be the right distance from the sensor. My shoe apparently bumps it sometimes getting on or off the trike which makes the magnet ring wiggle as it rotates. It seems extremely fragile; it even completely popped apart yesterday when I bumped it harder than usual as I got onto the trike. When it works, it works great! But does not seem like a durable design.

@electricbiketech Год назад

Superglue or small wood screw.

@monique-ik5ru 4 года назад

thankyou that was very helpful,especally the turn ``M`` PART ON,,,M,,,XXX

@maxheadroom1506 Год назад

my led is off when the controller is on and blinks when i pedal forward. I had to redo the collection because my controller has blue red black wires and the wire needed to be much shorter to fit into the box. The problem is that the motor is not turning even though the led works. I have an M5 controller. The settings are set for both throttle and PAS. Throttle works fine. What could be the problem???

@barbb5273 4 года назад

Will this work on a Sun Trike? The pedal setup doesn’t look the same.

@ryanfrank6102 4 года назад

Yes this setup will work for a sun trike. The trike in this video is very similar to sun trike.

@mradriancorona 6 лет назад

Thanks man where can buy ??

@electricbiketech 6 лет назад

@Adrian Corona: www.ebikekit.com

@jrnamida5470 3 года назад

How about a Torque Sensor instead so we can climb hills. Cadence slows down on hills, or long inclines. Means slow assist if you are not usings a 1,000 watt motor with a throttle.

@frantaximarbella 2 года назад

thank you very much, i upload a video with ebike installation and no idea what is this.

@williamsweeney6547 2 года назад

Where can I order a pedal assist sensor and the magnet s

@electricbiketech 2 года назад

www.ebikekit.com

@sachinms2772 4 года назад

What happens if you remove half of magnets between magnets could it expand speed limiter

@electricbiketech 4 года назад

No. You can change settings in LCD, no need to remove magnets.

@sachinms2772 4 года назад

@@electricbiketech basic cycle no screen settings

@electricbiketech 4 года назад

@@sachinms2772 ah so not our system. Couldn't tell you the result if you do that to yours.

@marcgini1443 8 месяцев назад

Doesn’t mention the one piece crank

@mathw2703 3 года назад

Why doesn't sensor flash when pedalling backwards?

@EBikeKit 3 года назад

Imagine pedaling backwards and thrusting forwards...

@mathw2703 3 года назад

@@EBikeKit that's not what I mean obviously, how does the sensor ´know´ when pedalling backwards? but i guess off-topic here..

@EBikeKit 3 года назад

@@mathw2703 it senses the polarity and frequency.

@mathw2703 3 года назад

@@EBikeKit ..that explains it..😭

@Aalphashark Год назад

Dear sir. Please pull your zip ties tighter next time.

@phildimarino4220 5 лет назад

with what motors (none shown) does PAS work? I did notice that no youtuber thought to show what PAS can hook up. Why is that? Are to assume something.? USEless without motor compatibility and hook up. useless.

@socialfreak6900 4 года назад

All PAS Cadence Sensors should work with all E-bikes as long as the connectors are the same, even if the connectors aren't the same you can splice the cables and solder a connector that is compatible with your controller, all PAS sensors work the same except for Torque Sensors, if your controller is built for a Torque Sensor a Cadence Sensor will not work and vise versa