Ebikeling Pedal Assist Sensor Installation 

Nothing to do with this video, but just wanted to thank you for the one some time ago, where you fitted Bafang battery UNDER the frame, on full sus. Would never have had the foresight/confidence to do it myself, without your help. But, the hours of pleasure I have had since doing it myself, with your expert guidance, deserve a very special THANK YOU, at the very least. Keep up the good work!

Thanks for this - I hadn't considered glueing, but it seems to be a common solution to my setup (with no ring nut).

I am struggling with the logic behind eBike assembly and your video has been a delight to follow. I subscribed because I can learn from you. I am English and often struggle with some American voices. Your voice is clear and easy to understand. Thank you!

Fantastic video, thankyou so much!!! Funny how all the vids ive seen on installing a rear hub motor kit don't seem to mention anything at all about how to install the p.a.s sensor. I've watched a load and it made me totally forget all about this important part of the full kits installation. Hopefully I'll be fitting my Voilamart 1500w 48v rear hub kit tommorow (if a few more little things im waiting on delivery turn up?!?) Brilliant video, sooo appreciated as I'd started to get worried about how to fit the p.a.s.

Extremely helpful. Thanks!

All these ebike manufacturers should make pedal assist that you don’t have to remove the crank pedal. It’s a freakin worse thing I’ve ever worked on bicycles.

I found out what was wrong with mine! I had it with the arrows going in the correct direction but it wouldn’t work- then I reversed the magnetic ring and backpedaled, then it started working. So now with both the sensor and the ring reversed it’s working!

Omg thank you! I've been going through hell trying to figure this out because my bike isn't set up like the instruction reference.

Thanks so much man I've been stuck for hours 💕

You almost answered all my questions I had, Good job mate. Thumbs UP👍👍👍👍👍👍

Well presented young man answered my question about which way the arrows face thank you happy biking!

Great how to, and mods! Thanks!

Mine came with disk that pulls apart and uses a lock ring that mounts on the outside groove to hold it together so you don't have to take off the crank! i found out the hard way after i tookoff the crank,pushed it on and it splilt in two...lol

Best tutorial I have come across, thank you!

You did just great on this instructional video.

Вот это ты молодец! Так коротко и ёмко всё объяснил!

Hey glad you are making videos again!

Great video - thank you.

Thank you you made it very clear and easy I was not sure thanks again

Beautiful!!, thanks!

Well done! Thank you

Awesome! Thank you!

Excellent

Hey Doug, I was considering getting a 1500w ebikeling rear motor. Do you think it would be faster than the Bafang BBSHD or BBS02?

Thanks for the video. What should be the whole length of the bottom bracket, when is 68mm?

WARNING ⚠️ make sure you have a gap in between your crank arm and the magnet disc. You can break your bottom bracket If you don't have a gap. VERY IMPORTANT.

thank you for your tips on how to install the sensor I like how you modify and make stuff work even though some designs differ on the crank. : )

Thanks Doug

Very helpful, straight to the point, cheers.

Thank you, great video. One question, My sensor is located on the sprocket side, (Zugo). What if the sensor spins freely? and slides in an out loosely? The teeth are not grabbing.

Thank you!

I understand that this method only works in some frames. I had a carbon bike with the Aston Rider kit and I switched it to a bamboo bike in 10 minutes and I didn't have to cut any cables

Question. Do you have a video about installing PAS to a hollowtech crank? I've been thinking changing from square tapered to hollowtech but I've no idea how and what parts do I have to buy. Thank you

this is a reallt interesting and usefull video. I did one of yours idea but I got a few mm too far from the sensor.. SO i'll be inspired to do something different

this helpt me very much, Than you!

I want to add a front hub motor kit to one of my e-bikes that runs totally independent from the original rear hub motor….can I add 2 pedal assist sensors at the same time?

Thanks from India

Tried number 3 first befor watching.if that fails.ill cut it and.attach it like you did on the second one, thankyou dude :)

I have a question, why’d you point out while showing us the glueing method that it was not a ebikeling PAS? I’m asking because I have a ebikeling kit and was hoping to secure the sensor with the glue method

The problem my bike shop said is that my Shimano crank is tapered and the PAS takes up room so that my crank are will not slide back on all the way, I can tighten the bolt but the crank is not seated all the way and the bike shop said it will eventually wear out the crank arm since it is not tightly seated. Is there a PAS system that will work in this case?

Is it possible to instal a pedal assist on a one piece crank?

Can I change my ebike fromsingle mode pedal assist to multi mode by any easy means?

I crazy glued my sensor to my BB with no lock ring

Can i add a front electric wheel to my rear assist e bike?

Back again! Happy Swede here... Have you had any problems with your extra battery on Xiaomi m365 scooter? Should I do it? Put an extra battery...

Hi does the arrow direction matter??

Hi I have a trike that's been converted to electric ,only the peddles are sealed and cannot be removed so how can I put a sensor to the peddle ,at the moment it's throttle only?

I have got 4 wires coming from a controller, but only 3 on a PAS sensor? Does that mean PAS sensor is not compatible?

Thanks

Nice video, but I would have installed the sensor on top of the bottom bracket instead of beneath it to minimize dirt, mud, water getting to it.

Hi, just a question because I am new with Ebikes and going to try to build one. Sooo if you have a throttle then you don't really need pedal assist sensor right?

But what do you connect the wire to?

what do i do if my bike has a single piece crank instead of the 3-piece one your bikes have?

Just got in a bike conversion kit and had a sensor in it. based on the video we installed it wrong but I was wondering what exactly the sensor does?

There are 3 kinds of sensor for square type ,octalink and hallowtech pas sensor

You have a video instruction on how to wire it to the controller?

im trying to configure my pas with my S866 controller and ESC brainpower 866 but my wheel has no Hall Sensor , i cannot make it work does PAS work with Motors with no HallSensor ? please someone helpme

Tks

how do you know what size to get, for a crank removal tool

The part around 0:46 about removing the ring nut with the ring nut wrench went by way too fast.

Are there no alternative sensors available to save pulling the crank off?

00:35 and 00:46 where do I get that tool and what is it called?

Guten Abend . Und wie viele BESSERE Magnete sollte dieser Sensor haben!? Ich habe ein altes Fahrradmodell; / Es gibt KEINEN Bordcomputer, sondern lediglich eine kleine Platine mit LEDs. und sein natürlicher PAS-Sensor besteht aus nur 5 Magneten!!! / Heute sind es 8 und es sind immer noch 12 Magnete. Ist es also möglich, 5 durch 8 Magnete zu ersetzen? Was wird sich ändern!? Wird es später noch Probleme geben!? Danke .

My sensor was too big to fit on the bearing plus there was no nut on the bearing So I just used silicone to fix it in place

I’ve installed this but my crank bolt keeps coming loose now every so often

3mm range between sensor n magnet rotor

Mine requires a hex key to remove the crank. 1/4-inch is too small and 3/8 is too big. :/

Do I have to put on the pedal assist?

How to turn off pedal assist

Fuck. I JB welded it on there and just realize it's 5 mm away. Can I bend the bracket towards it? The sensor will be at an angle.

Hey Doug Hnut do you have a private email I have a request for you

I used Blu tac 😂

first part: yes, second part: no

Nothing new here but thanx anyway.

I dont see why these are necessary! Lol...

У меня лучше получилось

What a load off waffle

Extremely helpful. Thanks!

Thanks