352-999-4477 www.joystickrepair.com Ship to: IMP 6672 W. Grover Cleveland blvd. Homosassa Fl. 34446 1800 717 1252 old phone number www.ElectricWheelchairParts.com Electric Wheelchair Parts and Repair Understanding Powerchair Programmers
You’re doing a great job Frank. Thank you. I’m going to call you when I get my Angel’s chair out of storage. It was running great six years ago then six months after her passing I plugged the charger in and the joy stick lights were flashing. I’ve watch your videos and know you can help. 🙏🏻🙂 I’m sure I’ll need batteries
I bought a Dynamic dx programmer and when I tried going to the tech setting it asked for the 3number code. Is their any way around this? I bought it used.
Hey Frank, Thanks for another video. We have an Invacare Pronto M91 chair. What programer is used for it and what is the cost? Also, we have an older Permobil C300. Can the same programer be used for it?
Have an Sp1B V 2.77 doesn't work on Pride Gogo's for some reason. Stuck in ' entering menu' mode when connected to molex . Tried key on /off etc Any special way to enter the controller? Buttons to push? SP1B supposedly is the ultimate programmer /engineering version. It does work on many others (also have 3 prone adaptor tip for sp1b that works on some newer scooters just not on some..like Gogo's..) please advise Thanks
Not sure your channel is used still but I have a quantum q6 edge and the controller went out I tried buying one but it was just fro a edge 2.0 not then Q6 but it would freeze on then Q boot screen does this need to be programmed to unlock or is it the wrong controller but the part number is the same but if it needs a programmer can you tell me what programming to use
That is a good question. The answer is no, the only way to get it back is through a programmer. We have one, $89 to reset. Would need the joystick and the module. Thanks, Frank 352 999 4477
From what I gather, the alltrack has an Rnet system. At this time, we do not have the programmer for Rnet. We can get you one, but they are not cheap. I believe around $550
Hi please can you tell me what it would cost approx if i take it to nearest dealer to have my speed limit corrected. this is due to putting smaller all terrain tyres on i am bnow loosing about 2 mph so need correction. but live on tight budget. so hoping it dont cost are and another leg. Thankyou mate liking yer vlogs. Bri n Sue
You do not have nearly enough information for me to help you out please let me know the make model of the machine if it is a Chinese made machine folding chair chances are there is no programmer that’s going to help you you can always call me at 1-800-717-1252
Do you know what programmer is needed for a quantum edge? I bought a PP1 quantum edition. But it doesn't read my chair. I know it works because I was able to adjust the speed on my pride Jazzy.
Great video by the way , but I want to ask about INVACARE G40 AND G40plus models. they need programming Can the DX programmer be used on them. or do they need a software like LINX? And could the MK6I program The DX joystick(DX-Rem 24SC) and (DX- REM 24S8) your insight is highly appreciated.
@@astrosmell thank you, I have 1 flashing light on my joystic DX-Rem 24SC) MANUAL inicates that i should rep[lace electronics, power module status light green light module status green joystick staus flashing one time, so I figured that it would require programing. will the DX programmer resolve this issue? I sent a message on your website , so I dont know if you have received it. Does frank has a mobile number , so I can do a contact on whatsapp ? Regards
Thanks for all your questions. We try to answer them all. If you have an open ended, or tricky question, please call. We are available 9 - 5 Mountain Time. 1800 717 1252. Thanks, Frank
Hi Frank, I am Nick from the UK to start I bought a 2015 quickie i cant read the model number but the seral no 4451224. it has a 3pin plug and the controller is a PG Drive Tech the label is printed D51122.03 and BN15020208 an embossed no in the plastic PA66-GF25 . my problem is its to vicious for my wife. can it be programmed to be slowed down , the joy stick to have more movement and generally made a lot more comfortable to operate. if this can be done is it possible to download software to update it. thanks
You have an RNET system. You will need a RNET programmer. The least expensive one is PC based. If we had one we could do it for you, but we do not. If you are interested in getting one give me a call. Frank 352 999 4477