P01 Backlight level P02 Metric=0 Imperial=1 P03 Voltage *DO NOT CHANGE* P04 Sleep mode timeout time P05 Assist levels 0=0-3 1=0-5 2=0-9 P06 Wheel Diameter in inches P07 Speed sensor magnets- *DO NOT CHANGE* P08 Speed limit P09 Zero start. 1=motor won't kick in until fater 6km/h P10 0=No Throttle 1=Only Throttle 2=Both P11 Pedal assist sensitivity 1=Assist Starts little rotation 24=Assist Starts after more rotation P12 Pedal Assist Start intensity 1=Low 3=High P13 Pedal assist magnet number P14 Max Peak Amp, Reduce for lower power. Do not increase P15 *DO NOT CHANGE* Lower Voltage Cutoff P16 ODO Reset, Hold up and down for 6 sec to reset P17 *DO NOT CHANGE* P18 Speedometer fine tuning P19 *DO NOT CHANGE* PAS level 0 enabled, 1= PAS level starts at 1
I played around with all the setting, including the "DO NOT Change" ones, how can I know which ones to change it back to so I don't mess up the bike? thanks for any advice
Yeah I did the same, I need to get #14 thru #17 correct, and make sure I don't kill my battery! 500w 48 volt 14.5 ah ....if anybody can help, or knows a factory reset? My senada drifter is basically exactly the same as this bike
I actually found setting the wheel size to 22" gave the most accurate reading compared to a phone app. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-dMBlVZNQhDM.html
Hello there I can not use my pedals on my ep2 I ride only with throttle and that’s not legal where I live Do you know how to fix this? Thanks in advance
Thanks for the info I'm a little confused on number 15, I have a 48 volt 14 ah battery I'm not sure what I should set that at any help would be great, honestly I'm not sure if I even changed it, if I did I don't want to ruin my battery,
Hi, how do I turn off the headlight. A week ago I noticed it was on until I took the battery away. Display don´t say it is on. When I put back the battery light started to light right away, even the display is still off. Pressing long time "up" does not shut it, only the display says then "light is manually on". Is there somewhere in menu I can choose light automatic?
My controller (X008-AAM003) and the M5 display only has settings 1 to 20. Would you possibly know what the correct settings are for this configuration?
Have you ever changed the LCD Display to the new Yolin LC80. My M5 display continues to accumulate condensation, and I am afraid of it burning out the controller. I continue to get an Error 030 which is a communication error. Any help would be greatly appreciated.
I don't believe it's a straight swap, I believe you would have to change the controller box too. Something to do with the way they communicate with each other.
@Midland Bullet Riders thank you. I was afraid of that. I am now wondering if there was a way to flash the LCD to the controller. Found a cable to program the Bafang Mid Drive. Donl you know if these are a Bafang Hub Motor?
If you have problems with cutting out and settings does not stay, you probably have a bad controller. I found two swollen caps in mine and when i replaced them with better ones the cut outs went away. But I cant still save settings and some some has no effect at all.
Hello I also have M5 display for my bike, but I cannot go through settings it asks me to enter a code with 3 digits but I have no clue what is the code, could you help me to find it ?
Hi my engwe won't switch on when I press the button on the handlebars. I've checked the battery (fully charged). I contacted the service dept via email they don't want to know. Have you come across this fault ? Thank you.
You've probably already tried, but I found this method of activating cruise control ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-k4Q8RVoo7V0.html I didn't realise these controllers were supposed to do cruise control until after I'd bought my bike so I won't be disappointed if it doesnt work.
ciao daniel, c'è un modo per aumentare la velocita ? avevo letto che si poteva modificare oltre le 5 massime che ci sono nel display..nel senso di farla andare ancora piu veloce...grazie fammi sapere :) e un altra cosa, per caso sai come si modificano nel display le miglia in km/h di velocita? saluti
@@djgiammylipari ciao ho risolto il problema dei miglia in km basta entrare nel menù premendo insieme il tasto più e meno e poi nel programma 2 lo imposti a 00 in modo che passa in km ma purtroppo dopo cqualche minuto che spegni la bici non si ricorda più le impostazioni stano forse c'è un modo per salvare. Se vuoi tiando il link in inglese che ti spiega tutte le funzioni del display
Morning great videos do you find that when you set the wheel circumference to 24 on the LCD screen the bike overestimate the speed and the miles? the only reason why i question this is on my phone I have a cycling app that shows different reading. Also if you measure the wheel it comes up more like 23 inch. What's your findings on this? Thanks
Can I ask what speeds your getting on the PAS levels? I have a bike with the exact controller except it only goes up to number 17 in the settings so im missing 18-26 like in your video. Anyhow my bike PAS 1 goes to 25km/h and that is the slowest speed. PAS 2 is about 29km/h and PAS 3 is 33km/h, after that you can't pedal because the gears on the pedals run out. Just wanted to see if theres a way to make the PAS levels slower? the retailer I bought the bike off seems to think its normal to go from 0 - 25km/h and have that as your slowest speed.
I get about 17kmh in pas 1. I have 5 pas levels. You could try to change 05P setting to 001. I'm not sure on yours. but it may give you 5 pas levels. Take a look at my other videos about changing the rear sprocket to less teeth, that will help with the pedal run out.
I've just received my ebike. With an M5 LCD. All my settings are the same but my bike keeps randomly cutting out when it gets below 48v Has anyone had the same problem
Hi, I ask you for advice, I changed the parameters from the display, let it automatically return to the HOME screen, then I turned off the display and removed the key from the battery. If I turn it back on after a few minutes it keeps the saved parameters for me, on the other hand, if I let more time pass, the default parameters return to me. Am I wrong something? Do you think the display or the control unit is faulty? The km / mile, on the other hand, always keeps me saved. Thanks
It appears some of the parameters save and some don't. I changed 05P and removed battery for a few days, and was still ok when I used again, 10P and 11P didn't. Think that's just the way it is.
Hi, Can you tell me how I can change Power Driven and Electric Driven mode to only Electric dirven mode, I have allready try P10 set to 1 value, but it do not work
I haven't tried it myself, but after you have put in the settings you require, turn off the display and back on again, see if that makes any difference, as I know it does when you change the speed settings.
I have the same problem. In my country throttle on a ebike is not allowed but i can't change the setting. Try to disconnect it from the controller but then i get error 034
Thank you very much for this video and the link to the M5 display manual !!! I've got an issue, perhaps you know how to solve ? When commuting from Mph to Km/h, the setting disappear when the power is off during some time (some minutes). The same for the P05 parameter, which allows to choose between 3, 5 or 9 help levels. Each setting I choose is erased after a while, and when I wake up the bike, these parameters (perhaps all, I did not check all of them) are resetted to factory settings... Anyone knows how to fix that ?
Thank you both ! Unfortunatly, i sold this bike to a friend that wanted it for his son’s birthday, and the bike has been stolen 2 days after in paris 🤬 This confirms that this bike catches the eye... and arouses envy !! That’ s why i ordered another bike, more discreet for my urban use...
@@MidlandBulletRiders thanks but i Tried that several times with bike on (and off aswell) but unfortunately no luck. Bike is new so maybe its locked now
I am hoping someone here may be able to help me with a problem I have with my Sheng Milo MX02S that uses this display. For some reason, I do not have any pedal assist above three. Checking my settings p05 is 1 which seems to be the correct setting that people are talking about in the comments for pedal-assist 5.
I'm trying to do the opposite on MX03, but I can't. I recently bought a controller and display that Rad Bikes use as an upgrade(40A sine + LCD8H display) the battery couldn't handle it, the motor is cutting off on load. So I switched back to old one until the new 25Ah battery comes with normal BMS 30A.
I also checked the max current draw on the original setup(click M button while riding until it displays current). 9A. Pathetic. It even drops when going uphill to 7. 1000W rated motor should use at least 30Amax, 15Arated controller. This one behaves like Bafang hub 750W, which is great.
Hi! I need help. I've messed up in the settings. I don't even know how. Now it's asking for some kin of pass. Whenever I try to turn on The display show only these " ----". I don't know any pass. I can't get into settings to make everything default. How do I reset it. I can't use my bike. Help pls.
@@MidlandBulletRiders Wired connection seems fine. When I turn on the display It shows thes 4 dash" ----" with backlight off. Is there any way to reset to default settings like we do with our phones factory reset?
@@MidlandBulletRiders hi when i try to get to the settings it takes me to a white screen with - - - - then when i press up or down each one changes to a number until i press m button is there a 4 didget code i need to enter if so where do i find this code thanks if anyone can help
The newer bikes with the M5 computer seem faulty. I bought two bikes and the second one came with an m5 which loses settings and the motor randomly works. The handle bar initially works and then after just stops working. It needs a new computer but the Aliexpress seller wouldnt send me one. They are just full of lies.
@@Humanature85 I just made any adjustments to the brakes at the caliper end and made sure the levers returned all the way, the cable shroud doesn't always seat there if you're not careful, if the motor cuts while riding, push the levers back with the back of your fingers to see if that is the problem? If it is the motor will run and you need to adjust the lever .
Good day everybody, Tried to throttle my bike to 25 km / h I have saved the value 25 under p08, Nevertheless my bike drives over 40 km / h I want to be legal on the road Can someone help me? Should I change something else? I am grateful for any help
Try setting it to 30. then turn the display off and back on again to save the setting. Also depends what controller it's using, they seem to vary between models. Check out this video explaining in more detail. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7VxYBNWSVYE.html
Hello Mr , I got a ebike EP2-pro 20" and I needed up with setting. What's the best setting ? Thanks . The motor lose power when I set at the maximum speed 5.