Epoxy Resin Art Pour Painting

Подписаться 1,1 тыс.

Просмотров 49 тыс.

50% 1

Ready for some relaxing resin pouring? In this video I did away with any instructions to go with it and just left it as a video to watch and to enjoy some relaxing music. I will make an epoxy resin art for beginners video that will talk through these steps so if that is of interest give my channel a follow :-)
FREE GUIDE: If you are considering taking up resin art as a hobby, or even a side hustle then grab my FREE guide on Resin Basics for Beginners on my website andysartlab.com
-------------------------------------------------------------------------------------------------------------------------
🖌🎨 ART SUPPLIES 🖌🎨
Resin: amzn.to/46ApieL
Resin Molds: amzn.to/3OhoT8z
Resin Dye: amzn.to/3DGvjcC
Measuring Cups amzn.to/43RbLgb
Alcohol inks amzn.to/3DGvjcC
Mica Powder amzn.to/3YpNVHd
Glitter amzn.to/3YpNVHd
Foil amzn.to/3Qnmxrn
Natural materials amzn.to/43Rghew
Pressed flowers etc amzn.to/43Rghew
Acrylic Supplies: amzn.to/3XyHUYi
Silicon for Molds: amzn.to/3PFNKFn
Vacuum Pot only: amzn.to/44eTTgo
Vacuum Pot and Pump: amzn.to/3pqr5SX
Pressure Pot: amzn.to/3JGgU3f
SAFETY EQUIPMENT:
3M Half Mask amzn.to/44X7n0w
3M Organic Vapour Filter amzn.to/45kEBH1
3M Eye Protection Goggles amzn.to/3OnMbJR
Nitrile Gloves amzn.to/3s4QkLy
-------------------------------------------------------------------------------------------------------------------------
✨🎇 FOLLOW ME ✨🎇
Tik Tok: / andysartlab
Twitter: / andysartlab
Instagram: / andysartlab
Web and Blog: andysartlab.com
Newsletter: zaap.bio/andysartlab
-------------------------------------------------------------------------------------------------------------------------
🔧🔨SOFTWARE I USE 🔧🔨
Link in Bio: 10% Off code 'zaap10' zaap.ai/?ref=a...
Boarderless Banking: Wise wise.com/invit...
Social Media Content Re-purposing: neon.ly/repurpose
Email Marketing: neon.ly/aweber
VPN: SurfShark: neon.ly/surfsh...
RU-vid Optimization: www.tubebuddy....
--------------------------------------------------------------------------------------------------------------------------
DISCLAIMER
These videos are for entertainment purposes only. Follow manufacturer instructions and always wear PPE when dealing with chemicals like resin. Some of the above links contain affiliate products where we make a small commission, but at no additional cost to you.

Опубликовано:

6 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@arpanbhatt3335 9 месяцев назад

very interesting art

@AndysArtLab 9 месяцев назад

Thank you so much 😀

@josephpoitras3090 11 месяцев назад

I’m just starting in epoxy resin. I really hope to reach that caliber someday. Question, how much does that design table now sell for? Round figure is fine.

@AndysArtLab 11 месяцев назад

Thanks very much. It looks harder than it actually is. You just need to start doing these art pours and you will get to know what works. I These sell for around the $100 + $150 USD figure.

@mohdjabir6828 7 месяцев назад

Sir, is there any such chemical available that if a design is made on a wet cloth with a roller, it will remain the same?

@AndysArtLab 7 месяцев назад

If the cloth was stuck to some kind of backing like wood then you could coat it in Epoxy Art Resin and it would protect it. You would have to watch for airbubbles and use a blue flame to pop them.

@ibrahimaktan5421 7 месяцев назад

Hocam merhabalar ben de bu işi yapmaya başladım ama kenarları sizin gibi olmuyor nerede hata yapıyorum sehpanın kenarları açık kalıyor

@AndysArtLab 7 месяцев назад

Thank you for your comment. First you need to tape the underside with painters tape to make sure you can remove any drips once it's dry. Next you need to make sure that it's 100% level so the resin runs off the edge evenly. If you have gaps you can run your gloves hand around the edge to make sure it's all covered with resin. I hope this helps.

@ibrahimaktan5421 7 месяцев назад

Teşekkürler hocam

@gabriellaragona3897 10 месяцев назад

Bellissimo davvero quanto è spesso il pannello? Grazie se mi risponde

@AndysArtLab 10 месяцев назад

Thank you 😍 The panel is 18mm thick.

@JudyKritikos 10 месяцев назад

Where can we get these MDF rounds???

@AndysArtLab 10 месяцев назад

I made mine and have a video on my channel how to make them if you have a router. You can buy them from some art supply places as well.

@SehrishNawaz-ki3iz 11 месяцев назад

What us This wood name?

@AndysArtLab 11 месяцев назад

The wood is called MDF: Medium Density Fibreboard. Its an engineered wood and its cheaper than plywood.

@daze8585 7 месяцев назад

I do pour painting and I’ve never seen anyone trying to blow the design out with a heat gun , the heat gun is only used to pop the bubbles , people usually use the hair dryer then let it dry before applying resin to protect the design

@AndysArtLab 7 месяцев назад

Thanks for watching. You are correct a heatgun is great at removing air bubbles. I find with a fast cure resign if its starting to cure while pouring the extra heat the heat gun provides over a hairdryer makes it a bit more viscous again to blow it a little further. I find that you have a little more control with a heatgun over a hairdryer in pushing the hotair as well, however I use a hairdryer at times as well.