If the SD card is not used, this board can still be used to add more sensors. This is one of the best videos I have seen which describes how to connect and program an ESP32-cam.
@@SaravananAL I am programming Esp32 cam using FTDI programmer but getting this error.I have seen many solutions on google but not working.Can you please see the following error and suggest some solution: a fatal error occurred: failed to connect to esp32: no serial data received.
@@hydraarjjun1399 Yes it was solved and has two possible solutions.When I select the wrover module from board it gets resolved.Secondly I checked programming arduino board from ftdi and it worked fine which shows ftdi was fine.You can program esp32/cam using arduino uno and you can find many tutorials on how to do that from youtube videos.Tell me if any of my solution resolved your problem or not?
Sir. I followed all steps you mentioned but still I am getting below error. A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header
Sir I had tried your this project as per your tutorial in several times , everything is working but when select face recognition / face detection my face it is not shows any square on the face and not working, although I have change my cam module with AI thinker but still is not working. I would be really grateful if you give me the solution.
havent you got the nts\Arduino\libraries\WiFi exit status 1 fd_forward.h: No such file or directory This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.
exec: "cmd": executable file not found in %PATH% Error compiling for board ESP32 AI THinker I got this error when i try to compile the code, anyone can help me with this? i have downloaded the wrover library and has exctract into the /documents/arduino folder , btu i still face this issue. Please help , thank you in advance
excellent job. you make a great instructor. even showed the pitfalls a person might run into if the camer or the programmer had insufficient voltage. thanks.
I programmed the ESP 32 cam as you instructed, however, when i try to get still image, i get a jpg file which is empty. It is as if my ESP32 camera is not able to click a still image that is supported. Need help urgently please
Thank you sir, but I got 0x105 error init. At first, I can acomplish until serial monitor gives me the IP address, but when I first access it, there just a blank black square. I reset it and then the serial monitor says "camera failed to capture" again and again. I unplug the whole thing, and then I try it again, now the serial monitor says "error 0x105 init" something like that
Appreciate the clear instructions. I however am unable to flash to the ESP32. All the wiring including the GPI 0 to ground was checked a number of times and i still get the message "A fatal error. Timed out for Packet header". also I note that the LED's Tx and Rx on the USB/UART connector do not flash at all. could something be wrong with the camera module GPI 0 pin. Appreaciate your help
I was facing so much trouble with uploading the code and no video helped me out. They kept saying that this was the solution and that was the solution... but the problem was the timing of pressing the reset button. 8:00 Thanks man!
Hi ! If I don't have an arduino, can I make Cam ESP 32 settings? Is there an option for motion detection? If a thief enters my yard and steals my camera, can I see the recordings on my server / my cloud ?
I can upload the code and esp32 cam also shows the IP address of the web server but I am not able to open the web server on my browser. The browser page says 'connection time out'. Any solution for this error?
Yesterday I have purchased and uploaded 2 times. Third time all connections correct and cause fatal error unable to resolve it all. I think cable or ft232rl or esp32 cam is gone.
Nice instructions, however it did not work for me after trying 100+ times. Plus now the original code is gone and esp32 does not come up as a WIFI on search, so the device is now useless with nowhere to go. Is there a solution where the device becomes just like new, i.e it can create its own wifi and atleast can work as a cam? please help
if i saw loading up to 100% but failed to follow instructions of pulling the jumper wire and.pressing the reset. Do i need to hard reset/erase? or just do the procedure again?
sir, I have tried it. Camera streaming is working, but I'm not getting any rectangle around my face. It seems like face detection is not working. Please help me with this
Absolutely amazing sir!! You have all the possibilities and errors. No other videos mentioned this! Thank you for making this wonderful video sir!! You earned new subscriber sir..
Can we upload the recording to sd card somehow? like it might be inconvenient to always provide wifi to the camera , might be if i use it on any project..thanks for explaining in such detail.
