ExpressLrs For Beginners | How To Set Up Elrs From Start To Finish

Подписаться 6 тыс.

Просмотров 1,9 тыс.

50% 1

Here Is A Full Step-by-step Video Of How To Set Up ExpressLrs (ELRS) For The First Time For Beginners Including Model Match Examples
3/27/24 - The video linked below is a continuation from this video. I go over many scenarios you may encounter with Elrs. Hope this information helps.
Also, this link goes to my very first official Livestream.. Enjoy the Breeze...
ru-vid.com9X0sbjsKaJs
Introduction
2:17 - Wiring and Understanding a UART
6:34 - EP1 Receivers
7:40 - ExpressLrs Configurator
17:12 - LUA Setup
25:40 - LUA to SD Card
25:45 - EdgeTX or OpenTX
27:45 - Running ELRS LUA
31:50 - Why Model Match
35:10 - Initiate Transmitter (TX) Wifi
39:15 - Receiver Firmware
42:40 - Update Receiver Via Wifi
47:05 - Get TX and RX to Communicate
48:50 - Final Thoughts
SUBSCRIBE!!!
3/10/2024 - New tool and information....
expresslrs.github.io/web-flas...
www.expresslrs.org/quick-star...
Contact Me, ScooterPie:
Propsoffohio@gmail.com
scooterpie.100
*If you would like to support this channel with $$$
venmo.com/PropsOff
/ propsoff
My Gear:
HDzero Whoop Lite Bundle - wrekd.com/products/hdzero-who...
HDO Goggles (V1 Discontinued) - pyrodrone.com/products/fatsha...
RapidFire Module - pyrodrone.com/products/immers...
Goggle Battery - www.amazon.com/Battery-GOLDBA...
Vifly Whoopstor V3 (Affiliate Link) - viflydrone.com/?ref=98tmocyr
Coupon 5% - SCOOTERPIE5
Rush Tank VTX - wrekd.com/products/rushfpv-ru...
Goggle Power Cable - www.dronecosmo.com/products/s...
Goggle Patch Antenna - www.foxeer.com/foxeer-echo-2-...
Goggle Omni Antenna - pyrodrone.com/collections/fpv...
Happymodel Slim Pro - www.racedayquads.com/products...
Radiomaster Zorro - www.buddyrc.com/products/radi...
Radiomaster Zorro AG01 Mini - www.buddyrc.com/products/ag01...
Radiomaster Zorro Case - www.buddyrc.com/products/copy...
Radiomaster Zorro Cable - www.buddyrc.com/products/copy...
RadiomasterTX16S - www.buddyrc.com/products/radi...
Radiomaster MAXPRO MCK - www.radiomasterrc.com/product...
Radiomaster Nano Receiver - www.buddyrc.com/collections/r...
Favorite 2-8S Charger - www.racedayquads.com/products...
Best Power Supply - www.racedayquads.com/products...
Strix 4s Parallel Board - www.readymaderc.com/products/...
Source One V3 Frame - pyrodrone.com/products/tbs-so...
Mobula6 Whoop 25K Motors - pyrodrone.com/products/happym...
Note: I have only one affiliate link, therefore, these links are where I purchase items and are here for your convenience.
This channel is showing monetized, however, all funds go back into the channel, if any at all.

Хобби

Опубликовано:

20 дек 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 36

@mfrfpv9079 5 месяцев назад

Merry ELRSMASS 🎄🎄🎄

@propsoff 5 месяцев назад

What the heck are you doing up...😳 I just wrapped up this massive edit and too tired to edit my XmasRippy... But I'll be watching yours soon...🍻

@jagadishkumarmr1067 29 дней назад

Hey, This video was really helpful!! I was just handed a Radiomaster Zorro with an external HappyModel modules and I didnt know how everything worked. It was so frutrating. Now I understand why Lua script is necessary and why the firmwares are necessary. Thanks a lot! Really helps for my project!

@propsoff 29 дней назад

I appreciate your encouragement and feedback. I'm glad it helped. I have added 2 livestreams with more information you may be interested in...🍻

@propsoff 5 месяцев назад

Hello Everyone! Thank you for subscribing to my channel and giving your support and feedback! Here I finally put together a how to for absolute beginners in understanding ExpressLRS setup. Hopefully it helps someone.... Enjoy the Breeze...👍🏻🍻👊🏻

@Smagsfpv 5 месяцев назад

Thank you 🙌 🍻

@Smagsfpv 5 месяцев назад

Thank you so much for taking the time to make stuff like this, it means alot to people like me trying to learn 🙌🙏

@propsoff 5 месяцев назад

I appreciate your feedback and encouragement.. I'm literally sitting here at 2:45a.m. making a Short, thinking, "what am I doing?".... Your feedback stokes the passion...👍🏻🍻👊🏻

@Smagsfpv 5 месяцев назад

@@propsoff im sitting her at 2:46 am watching your video so i can use my new zorro max. 😎 great stuff

@propsoff 5 месяцев назад

@@Smagsfpv 🍻

@davidlee50 5 месяцев назад

Reminds me of the old switchboard operator that connected phones between customers.

@toddsanford7757 2 месяца назад

ok, followed all the steps here and went from a elrs brick to a whoop that is bound and getting stick movement in beta flight. THANKYOU so much for this video and the help you gave me on FaceBook. I really want to donate to your page. or patreon. im just ready to go figure out how to setup the betaflight part and get my moving stick assigned to the right controll.

@propsoff 2 месяца назад

I appreciate your support and feedback.. I have a "Get in the air" video that goes through Betaflight...🍻

@propsoff 2 месяца назад

I just seen the notification, thank you! Very generous of you...👍🏻🍻👊🏻

@albertdrew7235 23 дня назад

The Boxer has Edge TX, building the LUA script in in Express LRS..

@marinehm 5 месяцев назад

I just recently updated the firmware on all my Rx’s and Tx. For the longest, I couldn’t figure out why some Channels were missing and I could not go past 250mw on my Tx. Long story short: make sure you select the right hardware in the configurator when building the firmware!

@propsoff 5 месяцев назад

That sucks, but glad you got it figured out...🍻

@propsoff 5 месяцев назад

What TX module do you prefer?

@Mupshot 5 месяцев назад

I have never found ELRS difficult, but I had started with Frsky plugged into my radio to flash. Aside from no silk screening on several boards. I just always bought HM EP1 and EP2 until radiomaster started to make them. Or at least put their name on them, I assume HM makes them for Radiomaster. I always look for the jump pad to identify the ground. The only issue I ever had was flashing 3.x to all the 2.x receivers in my fleet. accounting for the flash size difference, 4 out of 12 needed to be flashed using passthrough (2) or an FTDI (2). but yeah, that was a PITA, but still better than FRSKY for your diamond board with SPI, you must not be on BF 4.3 which has the ELRS 3.0 built in.

@propsoff 5 месяцев назад

I read the Elrs website several times and muddled through the process the first time. But yeah, it simple stuff after that.. I will have to look at my Diamond, I'm pretty sure it's on 4.3...🤔

@propsoff 5 месяцев назад

Also, the boards without silkscreening are 🤬...🤣

@albertdrew7235 27 дней назад

This video really helped me with my Boxer, where other videos missing key inputs. Thanks. Have a different subject question about myMG90S sevro. It rotates 180 degrees when pluged in. Is there a setting just to get 90 Degrees right & left movements? Thanks

@propsoff 27 дней назад

I appreciate your feedback.. Yes, you can. Change the weights of that channel...🍻

@propsoff 27 дней назад

Here's also a good resource you may find helpful...🍻 manual.edgetx.org/color-radios/model-settings/inputs-mixes-and-outputs/outputs

@albertdrew7235 23 дня назад

Morning, Lost my settings / ELRS being seen , have a issue with my Boxer not seeing the new "LAU" script. Its stilling showing factory "2.8.0" factory. I cannot even open the "ELRS". Not sure what I am missing. Have reflashes the setting several times 3.3 Thanks

@propsoff 23 дня назад

2.8.0 , isn't that the OpenTX firmware?

@propsoff 23 дня назад

Is it just saying, "Loading"?

@ttaylor9916 2 месяца назад

great stuff.. but you mention another video you did, but no link, and cant find it...

@propsoff 2 месяца назад

I have a video " Get In The Air" that is a detailed how to.. I have recently done 2 livestreams covering more Elrs - ill link below the first of 2 livestreams.. The "Get In The Air" video is a step-by-step guide to set everything up from new.. ru-vid.com9X0sbjsKaJs?si=_xeqasGV0rWARlYA

@propsoff 2 месяца назад

Get In The Air video.... ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-J3CoYYqEiZU.htmlsi=TPPboYtzegtTysvW

@trev.productions Месяц назад

yoo what stick ends are there on your controller?

@propsoff Месяц назад

Those are a design called GrizzlePuffs, I helped with.. you can get them custom printed by Mark McCollum.. Just PM him on Facebook Messenger...🍻 facebook.com/share/iQAbfmGYBN47wYdf/?mibextid=qi2Omg

@Mupshot 5 месяцев назад

I should learn not to comment while Im watching. do you create a model for each quad? I never use model match. I understand why you do. but it all depends on if you are prone to plugging in multiple quads at once, but I suppose if your are at a race or conducting a class. Im super paranoid of plugging in, like Ill forget and trash my battery, so I always unplug, and always use the same model for my entire fleet.

@propsoff 5 месяцев назад

No, I have all my sized classes on one model (all my 5inch racers on one).. I've accidentally plugged 2 quads in at a race after a crash. It's sorta scary, really, lol...

@marinehm 5 месяцев назад

I use model match for this reason: I have 5 quads 2” Freestyle , 2.5” Cinewhoop, 3”, 5” freestyle , 7” Cruiser/ semi-long-range. Now if I had just 5 5” quads then, no, I would not be using model match.

@propsoff 5 месяцев назад

@@marinehm Do elaborate... You wouldn't use model match?