PropsOff is dedicated to expanding knowledge of the tech and community involved in FPV and the quadcopter life in general. I appreciate your feedback and comments to expand the wonderful world in the air! In 2012, I had my first maiden drone flight and was instantly hooked. I sold all my rc cars, trucks, and helis to expand my new passion of FPV. I hope to see you in the air! Enjoy the Breeze... Yours truly ScooterPie,
Contact ScooterPie at Propsoffohio@gmail.com facebook.com/scooter.pie.100
Want to see things I use on my channel? It's easy.... Click the link to go to Amazon's website and check out my ever developing Storefront.. I found the affiliate program to be a cool way to see all the stuff in one place - $0.00. www.amazon.com/shop/propsoff
After lots of peer pressure, I now have Patreon and Venmo
#MOREFUNTHANAGROWNMANSALLOWED
Thank you everyone for your support! Enjoy the Breeze...👍🏻🍻👊🏻 *100% of all funds will be used to improve the channel. Thank You.
problem about alcohol is it leaves a residue on the connectors so is not good to use....a fibre glass brush is what you need as it is like fine sand paper and cleans back to original.
@@andyMSH700 I did use the fiber glass pad, the alcohol is 91% and doesn't seem to be too bad under the microscope. It's more to cut any oily residue (possibly from the gimbles). I'll look a bit closer next time since you brought that up .. I appreciate your feedback...🍻
Hello ! Thanks for the vídeo. Is there a way to solder that vtx antena whitout soldering the ufl connector ? I just bought the antena but not the ufl connector that you solder on the Esc I bought elrs too do you think is worth changing from frsky to elrs on mobula 6 ? I am not sure it it is worth because of the vtx limitation
@tecozu22 My pleasure.. I'm going to link a video below that I believe will answer your first question.... Secondly, I don't want to come off too negative, however, every single 1S FC I've had with a built-in VTX has failed. Currently, I only purchase the Betafpv 1S F4 AIO boards and add HDz or an OVX300.. So to answer your question, I don't believe adding anything of more cost to the Mobula6 board is wise.. I hope this video clarifies your conundrum...🍻 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-k_-SRFDGWpY.htmlsi=7VYeQUHBcUy1lfZm
@@propsoff thank you ! So the only upgrade that is worth is changing the vtx antena ? As i saw on your video the difference is big compared to the Stock one. And Maybe keep the Stock frsky module and antena, is that right?
@@Tecorenato My pleasure...🍻 That was my experience, the VTX antenna upgrade was 3x better. The receiver mod helped, but I'm not sure if it's worth the risk - damaging components soldering it in...🤔
@@JordanLewisFamily I appreciate your support and encouragement! I believe it does have Lead. It has a low melt point and the material code has SN-tin and PB-lead in it.. I have it in my (zero commissions) Amazon store...🍻 www.amazon.com/dp/B08YXYJWS1?linkCode=ssc&tag=onamzscottb09-20&creativeASIN=B08YXYJWS1&asc_item-id=amzn1.ideas.3HATG6SBWZ1S1&ref_=aip_sf_list_spv_ofs_mixed_m_asin
Don’t worry about camera clearness. You did excellent explaining all the points on crimping connectors. I am a rank amateur as I need to learn this but don’t have the tools yet. I wish I could have given you 5 stars ⭐️⭐️⭐️⭐️⭐️
@@bruceyoung1343 I had a few of these crimping tools and this kit was perfect for balance-plugs. I built a charging station and needed many independent connectors (male and female). Been a good kit for me.. I do not have a 2mm specific kit though.
My 3s battery reads 12v when I connect the ground lead and the far lead, but zero on the middle 2 connectors. The balance connector is visually intact. Haven’t looked inside the battery housing. Any thoughts on what the problem might be?
@@connorsisler1824 Your multimeter is reading 0 volts from the center pins? So you have the ground lead on the far pin (ground) and the red lead on one of the center pins, and its zero?
I've been having the shaft slipping issue happen quite often to my happymodel 0702 motors. I'm wondering if you know of any more durable motors or ones where this doesnt happen as often?
@itsjase92 So far, I've sent a new design to a person of interest and complained heavily on this issue to people around Happymodel. Therefore, I've been asking around and heard VCI is good. Being outdoor season, I'll admit, the slip-shaft issue is backburnner for now.. You're not alone in this frustration...🍻
@@propsoff Thanks for that! The only other ones other than the happymodel that seem to be available locally for me are the betafpv and the newbeedrone flow motors. Do you happen to know if either of these might be any better?
@@itsjase92 I've heard the Newbeedrone motors are decent, the Betafpv's not so much.. Where are you? Wrekd.com carries the VCI motors and ship everywhere I can think of...🤔
Great stream on the Bec totally agree there's a time and a place for every size just know when the right time to use the right size and as to the if you're promoting somebody I totally agree your time has to be worth something take care
@@apachesmokewoundedsniper No worries at all, my livestreams are very spontaneous.. I've had this one for a while and its worked everytime, I believe it to be a good one...🍻
@@LehtusBphree2flyFPV I have yet to find anything to complain about this scope.. Most excellent tool. I wish I would have gotten one a while back, may have been too expensive then, idk, Lol...🤣🍻
Thank you for the information. I read earlier today about it and I adjusted my settings with a bit of doubt, but coming across your clips gives me the comfort to confirm the changes I should make.
Please no one has helped me for years I have a micro sparrow cam get it connected on my googles but after say a minute the pictutre starts rolling down the screen and like think lines going from top to bottom
@@RaininCatsnDogs Your settings in Betaflight OSD tab for PAL/NTSC/AUTO are incorrect compared to the camera itself, possibly.. Wrong channels is also a possibility, I assume you check that...🤔
I know this video is about a year old. So I hope you still check the comments. I build on of these dischargers. My question is the light has gone out on the PWM board but the LiPo checker still register 0.90 volts. If I check battery with a volt meter it reads 2.54 volts. Is this normal?
@@crpyrce My pleasure. I appreciate your encouragement and support.. I try to think of all the different questions people have asked around the given subject.. Enjoy the Breeze...🍻
@@KingFPV I really thought that's what was going to happen, surprisingly, it did a pretty good job. There's some slouching at the top of the windows, but there's no supports. I printed a handful of my designs and they were good. I'm satisfied with it so far. I haven't printed TPU yet, however...🤔
@itslogical1381 That print was using the given sample from Bambu that was in the box.. I ran some no-name white matte filament from Amazon after, and it seemed to be the same - ridiculously fast and clean...🍻
@@propsoff the one that they give in box is pla basic which is very fast, but i was looking for some alternative to that may be esun hs will be similar
