Good afternoon friends!!! My name is Alexander, on my channel you will see many interesting solutions for creating a tool with your own hands at home! Subscribe to the channel, it will be interesting! INSTAGRAM / master___sh
Making a square length of timber round usually requires a lathe. Thats quite a complicated piece of equipment and not everyone has one. If you were doing 500 pieces the option above is very viable in comparison to a lathe and a gouging chisel.
Конечно я такое уже видел и с круглопильым станком,фрезером,паркеткой и т.п оборудованием-Всё это уже посмотрено и знакомо. Лайк за труд. Подписан ранее. Удачи.
Thank you, great video. It never occurred to me to do that with a handheld saw, that makes it very portable, witch I require sometimes. Again thanks for all the great videos you produce.
This is a great idea, much faster than a conventional lathe, and also enabling a consistent size and taper from one leg to the next. One could always make them fancier by then using traditional turning tools.
You shouldn't be pushing the wood through the table saw like that. It's too dangerous. If you think your hands are far enough away to be safe you're wrong.
Здравствуйте Александр!🤝воистину неисчерпаемы ваши идеи,лайк 👍!хороший станок.я пока остановил работы с деревом,металлом,начался огородный сезон.теперь только необходимый ремонт.бензопилу разобрал сальники поменять и руки не доходят собрать теперь😅.правда занялся,сконструировал и сделал самозасасываюший насос,у меня в огороде старая скважина,узкая,обратный клапан не проходит,вот сделал из огнетушителя и циркуляционного насоса свою конструкцию.
the moment of the saw was accelerated several times, what you think is dangerous was very slow and safe, but I will not get tired of writing this to everyone who will point it out to me
All the negative commenters and safety Karen's/Kevin's or armchair bots have no idea or are simply triggered by this guy's initiative and obvious expertise that eliminates risk through repetition and common sense. I doubt any of you could link his audience into your uploads!
А какова поверхность после такой обработки? Подозреваю, что сильно рваная, даже шлифовка не полностью скрывает дефекты. Мне кажется, лучше было бы использовать вместо циркулярки фрезер с пазовой фрезой, и подводить фрезу не сверху торцом, а боком, к заготовке
Why cry? For part-time enthusiasts like me, any cost saver is what I tend to make. Can't see the need for expensive tools to be white elephants to be used on a bi monthly basis. Rather applaud for simple designs to make. Unless you want to sponsor a cordless lathe. Small shop with cordless tools. Here in South Africa tools are expensive. 1 USD to R20 on any given day. Import costs, mark-up etc. As an end user, I definitely cut costs. Regards.
That's some sketchy freestyle table-sawing. I cant watch anymore. You cannot run a 8 inch wide board that 4 inches long in between the fence and the saw blade.
There is either time, or money. Each has different values to every one of us. Those with money would have a lathe. Those with time would build a clever jig like this one. Personally, I find that building jigs is at the high end of creativity, and I have a wall full of them. Some I use often. Some I look at and wonder just what in the hell I tried to accomplish. 😂
I agree. Time and Money are not the only variables here. Creativity, Joy, Pride, Contentment, Service, Friendship. Furthermore, more energy and materials go into building a commercial lathe compared to this home grown version. Good on you! Thanks for the video.
То было "в любой непонятной ситуации необходимо приварить подшипник" Теперь, в любой непонятной ситуации необходимо приклеить подшипник " Как вы достали сраные изобретатели
@@MA-SH , не забыл ещё ... Ну так там начало есть, могу прислать парочку к вам !!! Жду видео где подшипник привариваешь, а пока с приклеиванием видео отправляется к доктору... Так что терпение мой заокеанский злейший друг, всё будет. Ложись спать утро вечера... дальше сам знаешь! Полулях Саша, это ты что ли, сбежал?! Ай молодец! Доктор будет рад!
@@MA-SH You were cutting pieces with no rear table support. You used no push stick. I would stop someone in my shop right there. Thus my response. I would like to see more emphasis on safety on You tube videos considering the fact that entry level woodworkers may be watching...Not trying to run you but I added my educated response..
