Finishing the CH-750SD Doors

Подписаться 23 тыс.

Просмотров 2,8 тыс.

50% 1

You'll have to watch previous videos to see how I got the doors to this stage, but now I'm ready to finish them up. Even from this point, there's a lot of work to get the doors ready to install.
Orbital Polisher: amzn.to/3RyzSwa
Polishing Compound: amzn.to/3NsQsfm
3M 3-step Polishing: amzn.to/3tmRoLz
OPEN Arrow Sticker: www.aircraftstickers.com/placa...
Seats, Hoses, Fairings, and more!
www.KitplaneEnthusiast.com
iPhone Mount: amzn.to/3RjyZau
Light: amzn.to/3RrT8eq
Tripod: amzn.to/3TmYf2j
Fuse Holder (shown in Ep128): amzn.to/41ekDgg
DJI Cordless Microphone: amzn.to/3r1VXd0
FLUTING PLIERS: amzn.to/3FNgcQQ
MY FLUTING PLIERS: www.aircraft-tool.com/shop/de...
HOLE FINDING TOOLS: amzn.to/3WK1lwC
ICING Polyester putty: amzn.to/3DZhXZY
Hobby Saw: amzn.to/3TCOdXs
3/8" reamer: amzn.to/38Dxth2
USB Charger: amzn.to/2VWxBSB
Park Brake Clamp: www.aircraftspruce.com/catalo...
Dynon D3: dynonavionics.com/pocket-pane...
Adel Clamps: amzn.to/3ztVsI0
Snap Bushing (you NEED these): amzn.to/3gryDfm
Dremel Flap Wheel: amzn.to/3ztmXle
Air Hose: amzn.to/3wrqezA
Air Hose Fittings: amzn.to/3iIf2dB
Paint Gun (works GREAT for smaller parts): amzn.to/3vqDgMa
Air Filter for Paint Gun: amzn.to/3iHhfX2
USB Data Port (for Dynon): amzn.to/3iLsiOL
Paint Mix Cups: amzn.to/2RSM4gc
Fly Cutter (for fuel sender): amzn.to/3gvgXzO

Авто/Мото

Опубликовано:

15 дек 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@dapalmer79 7 месяцев назад

I have found regular toothpaste is also an excellent plastic polish. Additionally it leaves your canopy minty fresh!😊

@AnonyMous-jf4lc 7 месяцев назад

Lexan is a brand name for polycarbonate and plexiglass is a brand name for acrylic, much similar to Freon being a brand name for refrigerant. It's not uncommon to see panels have mold marks where they were held during forming. A wool pad for the first cut will help get some heat into the material and reduce buffing time.

@danLP07 7 месяцев назад

Can't thank you enough for continuing to post progress videos. Your attention to detail is unparalleled. Such a motivating series to watch!!! (There is nothing boring about watching your process! Thousands of times better than the garbage being broadcast on TV/streaming apps 😂) I signed up for a Zenith build course, thanks to you!

@jorgmichalowski7954 7 месяцев назад

Another great video with great tips. 👍 I have to remember to remove the protective film with the hairdryer.

@orvjudd1383 6 месяцев назад

Should use a little blue lecture on the latch hardware.

@NStraveler 7 месяцев назад

Someone drew on the side of a new to me planes fabric with a sharpie. I was told coconut oil can be effective at removing permanent marker, or in the case of a hard non porous surface using fresh marker over the dried marker line and wiping off quickly with a rag is an option. I have yet to try the coconut oil.

@davidrobins4025 7 месяцев назад

Thanks for the great video. That door really looks good. Your attention to detail is both rewarding and encouraging.

@kenfawcett4006 7 месяцев назад

Great job. Hopefully everyone will remember the blow dryer trick.

@grannyblinda 4 месяца назад

Curious, sincere question, can you explain your going with the Lycoming and not another ULP? Are you happy with the ULP 350iS in the Cruzer? Many thanks!

@n206ja 7 месяцев назад

Mark, when you use the 3M polishing compound #1 and then go directly to the 3D buffing compound, is that only for polishing the door glass or do you use the same combination for buffing paint, too?

@KitplaneEnthusiast 7 месяцев назад

When I used the 3M system for paint I used the 1, 2, and then 3. For the doors I figured the 3D buffing compound was pretty much doing the same thing as step 2 and 3 so I tried it and it worked great. Not sure if the results would be same on paint.

@richardturner6278 7 месяцев назад

Its pretty sad that you had the same issue as far back as the cruiser. That is plenty enough time for QC to correct the issue. I assume you forwarded a complaint to Zenith about this issue. That is just plain laziness on the part of the manufacturer.

@kennethsmolana9865 7 месяцев назад

Wet sanding would have been easier too.

@DustyLambert 7 месяцев назад

Rubbing alcohol removes sharpie.

@KitplaneEnthusiast 7 месяцев назад

I’m sure there are solvents that would work with the Sharpie but I didn’t want to risk damaging the window.

@RedNeckWelding 7 месяцев назад

Next time you need to remove permanent marker, go over it with a dry erase marker and it will wipe right off with no effort whatsoever.

@whathasxgottodowithit3919. 7 месяцев назад

Great video as always, It is not a big deal I guess, however it makes one wonder why the Q.C. department find it acceptable to send out parts in that condition to the customer, and Zeneth are not the only ones who do this.

@KitplaneEnthusiast 7 месяцев назад

I was thinking-Zenith may not even k ow about this. When they get the doors, they are completely covered with the tape, so they wouldn’t see the condition of them. I don’t think I ever mentioned the quality to Zenith even when I had the issue with the Cruzer doors. I’ll have to send Sebastien an email and just let him know.

@littlewingpsc27 6 месяцев назад

Are those areas you sanded out covered by the door frame so you can't see them in the final installation? If so, that might be why it isn't considered an issue. Might be caused by the tooling used to hold the sheet if they vacuum form the parts in a mold.