Fix Garage Door Cable Came Off Pulley

Подписаться 6 тыс.

Просмотров 128 тыс.

50% 1

DISCLAIMER / WARNING: THIS IS DANGEROUS WORK. I / GARAGE DOOR GUIDANCE WILL NOT BE HELD RESPONSIBLE FOR ANY INJURIES RELATED TO WHAT'S SHOWN IN THIS VIDEO. PLEASE CALL A TRAINED PROFESSIONAL IF YOURE EVEN THE SLIGHTEST BIT UNSURE OF TOUCHING THE GARAGE DOOR SPRING OR ANYTHING RELATING TO IT. USER / VIEWER ASSUMES ALL RISKS IN ATTEMPTING WHAT IS SHOWN IN THIS VIDEO.
How fix a garage door cable that's come off the pulley!
Link to winding bars: amzn.to/3yqrRAm
www.homedepot.....
Hopefully this helped and thanks for watching!!
Feel like supporting us with a tip? Venmo link below (:
account.venmo.....
This channel contains affiliate links to products. We may receive a commission for purchases made through these links (at no additional cost to you of course). Thank you for supporting us this way (:

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 110

@kitward24 2 месяца назад

Wow, that was a rollercoaster! I spent the whole 5 minutes on the edge of my seat watching him fix that door, only to discover it led to nowhere! Classic case of expecting the unexpected. Great video and even better twist at the end.

@GarageDoorGuidance 2 месяца назад

😂

@TheRancher03 7 месяцев назад

As a second safety, I place vice grips tight against the wall on each end of the tensioner tube. There are cases when the garage door cannot be lowered to be able to place the steel bars on the spring. In that case, I've raised the door all the way up and push the door further up on the bad side and use two (or one) screw drivers to slip the cable back on the roller.. Then take it down, wind correctly and add more tension with the bars. There has to be good tension at the bottom to be able to raise the door and not burn out you motor.This is all dangerous stuff so have to be on your toes.

@alexfletcher6764 3 месяца назад

Thank you so much for the video. Tensioned it with an allen key and a friend holding it which worked.

@TSyoyo 3 месяца назад

Worked for me! I didnt need to use vise grips though with the door down, there was no reason to hold it up. Other videos show the fix with the door in the up position but it seems way easier with it down because its like one wrap around the wheel instead of several were you have to keep tension on it. Anyway, glad I didnt have to call a repair service so thank you sir, I salute you.

@GarageDoorGuidance 3 месяца назад

With it down you have the tension to deal with usually, which is my guess why the other guys do it with it open. ( plus a lot of the time the cable comes off when it’s opened vs closed )

@Ambrizfamof3 5 месяцев назад

Thank you so much!! You saved us a giant stress and money. Totally worked for us and now we don't have to worry about it. I appreciate you

@VicksWander 3 месяца назад

Thanks for pointers. I used a pipe wrench on long rod with one hand while setting cable end into pulley groove with pliars with other hand.

@GarageDoorGuidance 3 месяца назад

😅

@Macantaya 11 месяцев назад

Straight to the point. Thanks for the help

@Velladog 2 месяца назад

Thank you so very much! What a great video!

@ericmolina7945 5 месяцев назад

I was able to fix my garage. Very clear instructions!

@hilandmalt 6 месяцев назад

As a guitar player, I plucked the cables afterward to see i they were in tune. LOL

@GarageDoorGuidance 6 месяцев назад

Haha were they?

@carmenk4018 3 месяца назад

.... gotta B# 😂😂😂

@itslitachristmaslightshow1378 Год назад

Thank you! Easy and quick

@redheelerdog Год назад

Thanks! Help me fix my derailed cable. Great instruction and safe.

@marlongordon390 Год назад

Very nice 👍👍 watching from Jamaica 💯

@ztesch04 4 месяца назад

Fixed the garage door thanks brother!

@robertjordan7323 Месяц назад

Thanks for sharing, worked perfectly

@isaachurtado3957 4 месяца назад

Good shit, the hardest thing for me was finding a pulley stopper

@yesicar83 3 месяца назад

Thank you very much for this video, It really help me.

@dlarricksmith 7 месяцев назад

WELL Done - Thank you for this. Perfect solution for us.

@leroycostner2981 6 месяцев назад

Thank you! It worked perfectly for me.

@edgarcortez8224 5 месяцев назад

Great video, help me out a lot. Got it fix

@ElCuervoArcano Месяц назад

And what happens when everything has relaxed and broken down for you. How can you relieve the tension of all the springs to leave it at 0 tension and start again? I mean, if I use the bars and the tension rests on them, can I unscrew the screws and little by little release the tension on the spring with the bars?

@GarageDoorGuidance Месяц назад

I definitely recommend you watch a handful of videos so you have a great idea on how it works in your particular case before attempting it

@tommyjohnson4162 3 месяца назад

Thank you

@jeffmason1704 Год назад

great vid simple explanation making the process so easy to follow. thanks for winding bar safety warning!

@PumpernickelBread25 10 месяцев назад

Where is the 1 2 3 from the little wrench coming from?

@GarageDoorGuidance 10 месяцев назад

Not sure what you mean

@kkutube1972 9 месяцев назад

I just vise grip the bar, I will try it this way next time.

@GarageDoorGuidance 9 месяцев назад

Bunch of different ways of to do the job, I’ve done that also 👍🏼

@blakematthews3108 Год назад

I have the same situation (left drum came unraveled) but I have 2 torsion springs. Same process? Just focus on left side of door?

@GarageDoorGuidance Год назад

You want to watch a couple more videos to be safe as there are a bunch of variations of the repair. The process is similar though you‘ll be dealing with more tension with 2 springs so it’s very important to have the correct tools. A good repair company should only charge a hundred or two to fix this and is what I’d recommend.

@forhisglory700 Год назад

Great video. Thanks.

@noahway13 3 месяца назад

Is that a door to nowhere?

@GarageDoorGuidance 3 месяца назад

Exactly

@ericjane747 Месяц назад

Snowed in.

@GarageDoorGuidance Месяц назад

@JoeTakagi00 2 месяца назад

What if you have 2 springs. One on each side as opposed to one in the middle like in the video

@GarageDoorGuidance 2 месяца назад

I would definitely recommend watching videos on a 2 spring setup

@conspiracytherapist2473 16 дней назад

Thx.

@denny9440 5 месяцев назад

haha and then he opens the door and there is no hole behind the door 😂😂😂

@GarageDoorGuidance 5 месяцев назад

Magic 😂

@forhisglory700 10 месяцев назад

About 3 months ago or so I had to replace an OLD cable due to rust at the loop. Your tutorial was very helpful - thanks. A year prior to that I replaced the cable on the other side with a brand NEW cable, and it snapped at the loop due to rust. My QUESTION is will I be required to replace these cables annually due to rust? Or is there something else I should be doing as a preventative measure? For example applying WD-40 directly on the loop after it has been installed? Unfortunately, water does pool in my garage by the cable loops; so that doesn't help. The rubber for the base of the garage door is worn, so that might explain water pooling in the garage. I live in Ontario, CANADA; so any suggestions and/or thoughts would be appreciated. Thanks.

@GarageDoorGuidance 10 месяцев назад

Hey there. The cables should be lasting 15+ years so I’d say the water issue needs to be dealt with first and foremost Awesome name by the way

@forhisglory700 10 месяцев назад

@@GarageDoorGuidance Thanks for your reply and feedback. Will do so; and thanks again.

@duanethomasdirtpile5737 Год назад

Much help thank u

@codylivingston1992 2 месяца назад

If you have two springs, do you want to release the tension on both of them or just the side that the wire is still in place?

@GarageDoorGuidance 2 месяца назад

You’d release both, one at a time. You need to watch a couple videos with dual springs

@codylivingston1992 2 месяца назад

I appreciate it. Figured it out

@MrDsturman 6 месяцев назад

Got me when the door opened to a wall

@GarageDoorGuidance 6 месяцев назад

lol I mean it’s a setup in the warehouse I slapped together real quick, working for now 😂

@MrDsturman 6 месяцев назад

@@GarageDoorGuidance I know I figured but I really threw me off cause the whole time i thought it would open to sunlight

@dawinner777 9 месяцев назад

Thanks and what if you have an opener

@GarageDoorGuidance 9 месяцев назад

You can detach it or leave it be depending on how far down it is

@jermaineharrison4782 10 месяцев назад

So if the door is down and even to the floor do I just put the cable back on the drum? Thanks for the video btw!

@GarageDoorGuidance 10 месяцев назад

Yes, you may need to do both in case the other comes off as you work with it

@jermaineharrison4782 10 месяцев назад

@@GarageDoorGuidancethanks they are both offline

@GarageDoorGuidance 10 месяцев назад

Then you need to re tension your spring I believe

@jermaineharrison4782 10 месяцев назад

@@GarageDoorGuidance thanks for the help

@RobertWojtow 2 месяца назад

Why after you are done is the left side down and there is a gap on the right side?

@GarageDoorGuidance 2 месяца назад

Not leveled one side was tightened the other was more loose

@RobertWojtow 2 месяца назад

@@GarageDoorGuidance but doesn’t that mean the tension would have been lost?

@GarageDoorGuidance 2 месяца назад

@@RobertWojtow are you referring to my video or yours has a gap?

@RobertWojtow 2 месяца назад

@@GarageDoorGuidance yours. The video shows the right side higher than the left.

@GarageDoorGuidance 2 месяца назад

If I remember correctly the foundation may not be level there

@B.collins7 3 месяца назад

You should paint one of these cartoon tunnels on the wall behind the door to nowhere

@GarageDoorGuidance 3 месяца назад

That would be pretty cool 😅

@DAMCOOLDAV 5 месяцев назад

Help! I used the pliers to hold the door at the highest point, loosened the set screws, and wound it up and reattached to the door (both sides), but when I finished the 2nd side, it completely unwound itself when I let go even though everything was back to normal. What am I missing?

@GarageDoorGuidance 5 месяцев назад

Sorry Dav, I think I know what you did but I can’t advise safely from here

@DAMCOOLDAV 5 месяцев назад

@@GarageDoorGuidance I ended up calling my garage door company, they came out and Immediately saw what happened. My spring was broke in 2, luckily they were able to fix right away, $400 :(

@GarageDoorGuidance 5 месяцев назад

@@DAMCOOLDAV gotcha, $400 is about right for a 2 spring setup ( depending where you are ) glad its squared away

@icontacked 7 месяцев назад

I've tried every size socket and none of them fit on this square type screw head

@GarageDoorGuidance 7 месяцев назад

11 mm spline type

@TravisNewton1979 Год назад

What if both cables came off? Assuming the same process just on both sides?

@GarageDoorGuidance Год назад

If both are off not likely, with the cables off your spring would likely need to be retensioned

@TravisNewton1979 Год назад

@@GarageDoorGuidance Only one cable came off but I completely lost all tension on my spring. The spring broke and looks like I will need to replace it

@stevkoria 10 месяцев назад

i have similar problem. But i have two car standard door with two springs. from what i see both the springs still have the tension in them.(same winds on both) which makes me think both springs are attached to same horizontal bar. And your solution should work. Since i have two springs do you think i should use two sets of winding bar and do exactly what you did @1:16 but with two springs at same time.(may be with help of friend on the other side)?

@GarageDoorGuidance 10 месяцев назад

No, do not do that. It works the same way when there are two springs it’s just twice as strong. Be very careful if you’re going to attempt this and also watch multiple videos so you have a good understanding of this type of repair

@stevkoria 10 месяцев назад

@@GarageDoorGuidance ohh you mean do not follow your steps? I saw multiple videos but most of them had lost tension in their springs .. mind seems to be present. Yours closely match with the problem I have.. I accidentally removed the cable while installing foam insulation on garage door .. and the door is tilted as one side of cable is now holding the door and trying to pull up.

@GarageDoorGuidance 10 месяцев назад

If you follow the steps you should be able to do it but again be very careful and cautious with every step. You may need to tighten both sides once the tension is resting on the bar. Depending where you are it shouldn’t too much to get someone over to fix it if you weren’t trying to deal with the tension and danger. Could be worth calling around and asking

@stevkoria 10 месяцев назад

@@GarageDoorGuidance thanks when you say tighten both sides you mean the drums screws or the springs? Also since I have two springs do I do same step on both sides or just one side.. if one which side?

@GarageDoorGuidance 10 месяцев назад

Drums, don’t touch the spring screws at all. One side and you can do it from either side. Keep in mind this something that can cause serious harm. Proceed with extreme caution

@MegaStreet11 Год назад

Can this be done without those bars?

@GarageDoorGuidance Год назад

Not likely

@chezpoulethomestead648 11 месяцев назад

My issue is very similar but each time I open the door over half way the cable loosens and unspools

@GarageDoorGuidance 11 месяцев назад

Spring tension is either too loose or the spring is not on the correct side

@netchannels8372 Год назад

My garage torsion spring broke after 18+ years, so I ordered another spring using the SAME SIZE shown on the broken spring. Installed it on my 8ft door which requires 33 to 34 turns. I’m up to around 45 quarter turns and when I lift the door halfway it falls to the floor. I noticed that this new spring did not expand out as far as the previous spring. It’s about 3-eighth inch short of the indentation mark of the old spring. Should I do 33 quarter turns and tap spring to stretch it out to the old spot on the shaft?

@GarageDoorGuidance Год назад

What springs are you working with?

@netchannels8372 Год назад

@@GarageDoorGuidanceDura Lift 225 x 2 x 26 #2 Red Rt Wind

@GarageDoorGuidance Год назад

You have 2 of these on your 15/16ft x 8ft tall door ?

@netchannels8372 Год назад

@@GarageDoorGuidance I have 2 garage doors, each door has its on torsion spring and garage door opener.

@GarageDoorGuidance Год назад

32-34 quarter turns is what’s required for the 8ft tall doors, if the spring isn’t lifting the door it’s either the wrong spring or placed on the wrong side. The spring has to be placed the correct direction. One way to tell is to look at the wire end where you wind the spring. It should be facing the header not you. Hope that makes sense

@BIKESnSKILLETS Год назад

But why DOES it come off?

@GarageDoorGuidance Год назад

Bunch of different scenarios, most common are that the door bumped something going up or down or incorrect springs

@johngatsby1473 5 месяцев назад

It's amazing how easy this crap is and these clowns are over here trying to to charge 125.00 to come do this.

@GarageDoorGuidance 5 месяцев назад

Respectfully $125 is very fair haha most guys won’t even come out for less than $100 where we’re at as it hardly covers costs

@bibmitchell6542 Год назад

Drum, not pulley

@GarageDoorGuidance Год назад

Keyword research tells a different story

@bibmitchell6542 Год назад

@@GarageDoorGuidance 🤣🤡

@ggmelendez9743 Год назад

@@bibmitchell6542 you gotta understand, this generation of service "men" learn a trade and then they all cant wait to get on youtube to show millions of customers how to fix their own stuff, taking millions of dollars out of their own industry each year, in return for a few hundred dollars in ad revenue...these kids dont even get their hands dirty, and wear sneakers instead of boots...do you really think they care about calling a part by its actual name?

@iggy9740 Год назад

@@ggmelendez9743 what kind of fruity comment is this? Boo-hoo - The scary man in the scary RU-vid video is helping other people with their garage door problems!! Really? This is it? This is the hill you die on? You're the definition of pathetic.

@PumpernickelBread25 6 месяцев назад

You dont fo a good enough job explaining what you are doing. ""One, two, three", what?

@GarageDoorGuidance 6 месяцев назад

Sorry when tightening the set screws down you don’t want to overdo it so I do 3 turns once I feel tension