Focus ST/Focus RS COBB Motor Mount Rear 2013-2018/2016-2018 Installation

Подписаться 246 тыс.

Просмотров 92 тыс.

50% 1

Bill shows you how to install a COBB Rear Motor Mount on your 2013-2018 Focus ST or 2016-2018 Focus RS.
Eliminating the troublesome wheel hop on your 2013, 2014, 2015, 2016, 2017 or 2018 Focus ST or 2016, 2017 or 2018 Focus RS, this sensational Rear Motor Mount from COBB is a stunning enhancement.
Featuring a machined 6061 billet aluminum construction, custom voids/recesses molded into the 85A durometer bushing, further assisting with absorbing vibrations.
Using this rear motor mount you'll be improving your stock engine by reducing engine sway, enhancing traction and lowering the chance of annoying wheel hop.
Purchase Product Here:
www.cjponyparts.com/cobb-moto...
Check out more Focus ST/RS parts from CJ's here:
www.cjponyparts.com/ford-focus...
Check out more COBB parts from CJ's here:
www.cjponyparts.com/cobb-tunin...
Subscribe to CJ Pony Parts on RU-vid here:
ru-vid.com_c...

Авто/Мото

Опубликовано:

25 июл 2016

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 76

@cassiusnoyb6499 5 лет назад

Drove an hour to my parents to do this mod just as it was about to get dark and i finished it in an hour i was so hyped to get it on XD Thank you so much for the tutorial love from texas!

@bangurowned 6 лет назад

Easily one of the best mecahnics i've seen on youtube videos as far as wrench turning habits is concerned.. Great vid.

@jumbotrack3090 3 года назад

It never goes this easy

@manuelsantellan8808 2 года назад

Tell me about it. Was on my back trying to get them damn brackets out that hold the down pipe. No go, he got them out like a magic trick 😂

@nicholasjarrett2055 5 месяцев назад

@@manuelsantellan8808just did mine and I laid under the car for a hot minute like how the fuck

@JCarterCARS 6 лет назад

Thanks Bill for all your help over the years. You seem to always have videos for the vehicles and modifications I choose. Appreciate the specifics in all of your videos.

@jessekeltnerman420 6 лет назад

The best and the easiest to install. Every focus st owner should have!

@ThomasPowersYouTube 6 лет назад

Can't express how awesome, high quality, and helpful these vids are. keep em coming! (and also please do a "how/were to put jack-stands for the Focus ST)

@bobking7386 5 лет назад

Pinch welds

@801speed5 Год назад

the same place as every other car.. LMAO

@SWEATY-Braaapper666 6 лет назад

Just did this to my 14 st today and love it...you have the best tutorials...followed every step and diidnt have any problems...thanks!

@jordenetter7707 4 года назад

How is the vibration?

@SWEATY-Braaapper666 4 года назад

@@jordenetter7707 dont have the car anymore but It really wasnt bad with the Cobb mount...a little worse than normal

@awhitness 5 лет назад

This will add NVH. Wheel hop is greatly improved, also amazing how it changes shifting. No longer do you have to feather into gear to avoid clunking. But the vibration at slow take offs make this a give and take mod. The improvement in shift quality for me out weighs the vibration. I was thinking about drilling out maybe 2 - 4 of the holes to soften the mount just a little...

@fubutubu2132 8 лет назад

Just installed this on my 2016 FoST and it really makes a huge difference. Shifts are smoother and the slop is gone when leaving from a stop. Feels like a different car.

@stephensmyth4830 6 лет назад

Fubutubu2 did you notice vibration on idle? did it subside

@ADDwithJTC 5 лет назад

@@stephensmyth4830 I'm about to install mine 17 ST. You have vibration at idle?

@stephensmyth4830 5 лет назад

@@ADDwithJTC yeah, slightly. Normal driving was like normal. Over time it did subside, and it was much nicer to drive. The only thing that annoyed me was when I turned the car on, it vibrated loads until the untill the revs settled.

@ADDwithJTC 5 лет назад

@@stephensmyth4830 thanks for letting me know it subsides. Going to my neighbor's garage now. You were just in time. I was almost about to not install it after my oil change.

@stephensmyth4830 5 лет назад

@@ADDwithJTC no problem bud! Yeah give it a couple of weeks, but the positives 100% outweigh the vibration. No more wheel hop etc

@manuelsantellan8808 2 года назад

That bracket… Couldn’t get them out for squat in my 14’. 🤷‍♂️

@bigmartxyzx2212 6 лет назад

Great vid for prepping how to do it, notice you didn't show how to torque the rear 15mm stud, it's a pig, I couldn't get a ratchet near it let alone a torque wrench.

@GeordieUSA 8 лет назад

I wish you were located closer to me, so you could use my RS to make some videos!

@victorgonzales7961 6 лет назад

So one of my friends thought that the downpipe nuts were supposed to be torqued down and snapped one of them off. Is that bad that I only have one bolt there now?

@gregory7887 6 лет назад

How does the rear motor mount bracket come off? I move it around in every direction and I can't get it off. Yours the falls off.

@undergroundst6951 4 года назад

What’s the bolt length or where could I find a replacement

@johnlefever3220 2 года назад

How does this one compare to the cpe stage 2?

@mustang2005 Год назад

I lost the oem bolt you unscrew @ 3:52 any chance you can tell me the size so I can buy a replacement? (I reinstalled the stock mount) It's the only ford oem parts screw that's not listed unfortunately. I would really appreciate this as the screw I have in there now is too short and makes me nervous it's going to snap.

@Rickytiger97 3 года назад

Will i need to support the engine?

@Theromanticrejeck 6 лет назад

do you know if the RMM for the focus is that same as a Mazda3/speed3?

@kurt_117 5 лет назад

yep exact same mount, prbably no help 10 months on but yes it is the same

@harrysharp9922 6 лет назад

I have a 2017 diesel focus and need a rear gearbox mount which one do I need please

@subwayguy1610 8 лет назад

Great video, but curious as to why you torqued the mount itself?

@thomasgipson1616 7 лет назад

probably so it doesnt come loose by vibrations

@mhautovlgs6957 4 года назад

I can't get that last bolt that holds the arm in place loose. Its the one up and in back. Hard to get at. Not the one on bottom inside near main bottom mountbolt.

@bricynpowell9330 2 года назад

same here been cranking at it for nearly 30 mins. sprayed wd40 got a bigger ratchet, tried an impact seems impossible.

@josephstephen2010 7 лет назад

Installed one of these on my '16 FoST a few months ago. Definitely a noticeable decline in torque steer, but the additional NVH almost makes it not worth it. After months my car still shakes at idle. I thought it would settle in a soften some but it hasn't.

@ADDwithJTC 5 лет назад

Was about to go install mine right now 17 ST. Vibration at idle that bad? I saw someone else mention it but didn't say almost makes it not worth it. Scaring me.

@skimshady 4 года назад

Jason Cotellessa did you go through with it?

@codyford8657 Год назад

There is many different rmm from different companies, some have different bushings.. I have a softer one from whoosh and I get only a slight amount of vibration at idle but it feels like it's supposed to be there. This cobb rmm might have a more ridgid bushing then some others .

@kg4234 7 лет назад

Did you support the engine while you did this? Or is not necessary?

@Zerogivengarage 7 лет назад

There are two side mounts that support the engine. It will rock front to back a little but its safe.

@brett5898 5 лет назад

@@Zerogivengarage be careful. One of my side motor mounts was failty

@fritzjean-philippe2464 5 лет назад

ratchetcityrider318 I was under that car with 2inches of clearance. You confirmed my fear

@JP-uk9uc 4 года назад

I was shocked at how much vibration there is at idle, 800rpm. I'm just wondering what's coming loose given how much vibration there is. It's just fine down the road, but waiting at a stop light there's just too much plastic in car to not rattle because of it.

@LogosLFTG 2 года назад

Did this get better after it broke in?

@clayreq 5 лет назад

About how long does this process take if I'm using a lift? Just for the rear mount.

@cjponyparts 5 лет назад

clayton requet with a lift you should have no problem getting in done in an hour or less

@clayreq 5 лет назад

@@cjponyparts Thank you!

@therealsixthirtythree 2 дня назад

I love the CJ videos when they install things.. ...annnd reinstall your dp bracket...((cut scene))...((cut scene))...magically snaps right in. psssh come on..show it whooping your ass

@crf150rRider6 7 лет назад

Can this be done with the car sitting on ramps?

@novastar2486 6 лет назад

Yes, but it is quite cramped and those two metal brackets are a PITA to remove AND install.

@nevercedes2070 6 лет назад

Yeah, everything is very do able just be prepared to sweat a bit

@cassiusnoyb6499 5 лет назад

Hell i did it in about an hour but yes it is a bitch there are two screws that are a pain but the rest is easy.

@jacksonmeredith7595 5 лет назад

Will an st rear mount still fit an se?

@FuzziesConnected 5 лет назад

Why would you buy a rmm for your se?

@bigbarrettbob 5 лет назад

If you want a RMM for your SE check out AWR mounts they make one specifically fit the SE. Although I don't know why you'd want one for an SE...

@metaljew4456 8 лет назад

This makes just such a difference in your ST you will not believe it. You can pick up the Ford electric mount for $50.00 bucks. It works Great also! This is a MUST DO UPGRADE IF YOU HAVE A 2013-1st QTR 2014 ST. No more wheel hop, no more horrible smashing noise of the engine trying to jump out of the engine bay!

@WorldsOkayistGuitarPlayer 7 лет назад

I have a 16 FoST. I believe it comes with the electric mount, do you know if thats correct?

@jacquelynking8521 6 лет назад

Focus RR yes but the electric one is still junk

@ADDwithJTC 5 лет назад

@@WorldsOkayistGuitarPlayer I have the 17 ST. Still tons of wheel hop with electric mount. Just got my cobb mount in the mail. Nice day. Bout to go install.

@salvadormunoz8922 8 месяцев назад

I can’t remove the stud at 5:09. Too tight. Any other tools than a wrench. Can’t remove it with ratchet. Not enough space

@undergroundst6951 4 года назад

How would you get a stripped bolt out of the torque dampener

@cjponyparts 4 года назад

I haven't had to do that but I would assume you could remove it, drill it out, and helicoil it.

@undergroundst6951 4 года назад

Could you just straight drill into it little by little?

@r1tual226 7 лет назад

Kind of stupid that Ford's stock mount is so bad that there is a noticeable difference in installing an aftermarket one. Of all the parts that should give a noticeable feeling when upgraded, a motor mount shouldn't be one of them.

@Zerogivengarage 7 лет назад

Ford even upgraded the original mounts to the E Focus which is better but there is still room for improvement.