Тёмный
No video :(

Ford Escape 1.6L Turbo Valve Cover Gasket & Spark Plugs Replacement - 2013 - 2019 Fusion, Fiesta 

Hardly Moving Productions
Подписаться 57 тыс.
Просмотров 73 тыс.
50% 1

This video will show you how I replaced the valve cover gasket and spark plugs on a 2013 Ford Escape 1.6L turbo ecoboost inline 4 cylinder engine with 112,000 miles. This engine is also used on the Ford Fusion ('13 - '14), Fiesta ('14 - '19), and Transit ('14 - '16). The repair procedure on these other vehicles should be similar to the Escape.
The customer had noticed constant garage floor oil leak stains appearing between the back of the engine and the firewall. His local Ford dealer informed him that his valve cover was leaking when he brought the car in for an oil change. He was also informed that the car was overdue for a spark plug change. Considering turbocharged cars like to eat up spark plugs, replacing the plugs with the valve cover gasket seemed prudent.
Removing and replacing the valve cover gasket on this 1.6L motor can be both tedious and time consuming. The problem was there was so much "stuff" positioned on top of the cover that needed to be removed ... including the cowling below the front windshield that hangs over the engine. Once the cover was off, the old valve cover gasket was dry rotted and brittle with visible oil stains around the outside edges. The gasket definitely was shot and needed to be replaced. I used Felpro as the replacement gasket which I believe is a silicone based material. It should last longer than the factory rubber gasket. To prevent rubber hoses from dry rotting and to ease hose installation, I use Permatex dielectric tune-up grease which won't swell rubber like what petroleum grease does.
If you'd like to make a donation to the channel, please follow the link below: paypal.me/Hard...
Parts & Tools:
FEL-PRO VS 50872 R Valve Cover Gasket Set
amzn.to/3dWAesz
Genuine OEM SP532 Iridium Spark Plugs (4 pack)
amzn.to/3tazfv5
Ford Escape (01-17), Mazda Tribute (01-11) & Mercury Mariner (05-11) Haynes Repair Manual
amzn.to/3vafaX9
Hose Clamp Plier Set
amzn.to/3fmgOlA
Permatex 22058 Dielectric Tune-Up Grease, 3 oz. Tube (Eases installation of rubber hoses and provides dry rot protection)
amzn.to/3qrnE8N
Push Pin Pliers (To grab, squeeze locking tabs and remove electrical connectors)
amzn.to/2OiwJnj
Milwaukee 2457-21 3/8-in Cordless M12 Lithium-Ion Ratchet Kit (Makes quick work on small nuts and bolts removal and installation)
amzn.to/3t3bSTK
TEKTON 6943 Precision Pick and Hook Set, 4-Piece (helps to get under and release the electrical connector tab locks)
amzn.to/3btELmk
OEM TOOLS 22887 5/8 Inch Magnetic Spark Plug Socket, 3/8 Inch Drive (Those rubber inserts to hold spark plugs eventually wear out)
amzn.to/3kZpU6b
As an Amazon associate, I earn from qualifying purchases. Thank you for your support!
Please Subscribe: goo.gl/x6fySQ
#escape

Опубликовано:

 

22 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 298   
@grease_monkey9044
@grease_monkey9044 2 года назад
This is what every repair video should be like.... high speed thru the b.s and detailed instructions for the abnormal parts.
@hardlymovingpro
@hardlymovingpro 2 года назад
You're right and thanks for your comment and support!
@grease_monkey9044
@grease_monkey9044 2 года назад
@@hardlymovingpro it helped smash out the 4hr book time job in a fraction of the time!
@hardlymovingpro
@hardlymovingpro 2 года назад
4 hours? Wow!
@Jtavera67
@Jtavera67 Год назад
Great great great video
@brucequigley5803
@brucequigley5803 Год назад
Thank you very much! At 160K miles, the valve cover gasket finally gave out and I barely made it home with oil soaked plugs! She’s running great again.
@hardlymovingpro
@hardlymovingpro Год назад
Nice work!
@brasilnut10
@brasilnut10 11 месяцев назад
I have a 2013 1.6 Escape and I have to tell you that your dedication to putting together such a detailed video is invaluable to all weekend home mechanics out there and i am very grateful!!! Now I have a guide to follow as i ran into a lot of the same issues you ran into ie: those darn variable timing solenoids spraying oil everywhere! I'm in my late 50's now and just chuckle to think back when we were younger and didn't have the benefit of watching you tube videos as it is such a great resource. Again, great tool but nothing without dedication from people such as yourself that really put great videos together. Keep up the great work!👍
@hardlymovingpro
@hardlymovingpro 11 месяцев назад
Thanks for your kind critique of this video! Quite honestly, when I first approached this job, I was scratching my head. Where do I begin? I figured take everything on top of the valve cover off! After I dived in, it was like "now what's in the way???!!!". 😩
@davidr.miller5171
@davidr.miller5171 Год назад
Update: 10 Sept 2022: on 2014 Ford Escape, 1.6 ltr . Just completed the valve cover replacement: Your instructions were on the money!!!. The only problem I had was at the fuel rail. Two of the injectors came out with the rail. Easy job to put back. All parts recommended by you were correct. The job took me 4 hours to do. Thank god for dielectric grease.
@hardlymovingpro
@hardlymovingpro Год назад
Good and you and thanks for sharing!
@chops1sc
@chops1sc Год назад
One of my fuel injectors came out too. Did you just push it back down? It seems to be a little “wiggly” compared to the others.
@hardlymovingpro
@hardlymovingpro Год назад
Doesn't matter if the injector came off from the top or bottom.
@chops1sc
@chops1sc Год назад
@@hardlymovingpro Thanks!
@SkyyMi
@SkyyMi Год назад
Great to know it can be done without removing the injectors or the high pressure pump. Really wanted to avoid doing that. Thank you for the video
@hardlymovingpro
@hardlymovingpro Год назад
You bet 👍
@chasethatcher7313
@chasethatcher7313 20 дней назад
Thanks so much for the video!! Just finished my valve cover gasket and replacing my injectors at the same time. Took me 4 hours and saved me a ton of money. I’d like to add that it is supposed to be a 3-stage torque on the valve cover bolts. 5 nm 9 nm 10 nm There’s also a specific sequence to torque the bolts that I found shared in a forum. Thanks again!
@hardlymovingpro
@hardlymovingpro 20 дней назад
Thanks for sharing and glad it all worked out for you!
@TV-ih8lw
@TV-ih8lw Год назад
I have an estimate that is about $1,200 to replace my valve cover and spark plugs on '13 Fusion. Definitely going to take on the task of fixing it myself. Appreciate all the info!
@hardlymovingpro
@hardlymovingpro Год назад
That's a huge price quote on a job that shouldn't take at most 3 hours.
@sidewayzmike
@sidewayzmike 11 месяцев назад
Ouch
@scottydavis1813
@scottydavis1813 10 месяцев назад
Gone are the days of the 30 minute valve cover job. I am going to do this on my wife’s 2013 fusion. It was done twice by the dealer under warranty but this time I will do it
@hardlymovingpro
@hardlymovingpro 10 месяцев назад
Use FelPro gaskets in lieu of Ford OEM. May have better luck with longevity.
@TheYellowDartt
@TheYellowDartt 2 года назад
2013 Ford Fusion Here. This saved so much time and headache. Ty!
@hardlymovingpro
@hardlymovingpro 2 года назад
Good for you!
@RickHebrews12
@RickHebrews12 Год назад
Thank you so much for this video. I was able to successfully do this job because of your help. The other comments of fails seemed to concern the injectors, so I was very careful in removing the fuel rail without disturbing the injectors, and had replacement o-rings ready to go on. Had to order an entire kit for each injector to get the top o-rings, which I replaced as you instructed. Thankfully I did not have to use the other parts of the kit, because the injectors were undisturbed while removing the fuel rail. For others thinking of doing this -- take notes, take your time, be prepared. Hope you have success. Thanks again!!
@hardlymovingpro
@hardlymovingpro Год назад
Good for you and thank you for sharing your repair experience!
@jaygorippa6746
@jaygorippa6746 4 месяца назад
You're a super hero brother! Watching this video made the job 10X quicker when I did it.
@hardlymovingpro
@hardlymovingpro 4 месяца назад
Good for you and thanks for sharing!
@Southern-Reloading
@Southern-Reloading 2 года назад
Thank you for the very detailed video. I’ll be changing my valve cover gasket this weekend. My local Ford dealer quoted me $850 for this repair!
@hardlymovingpro
@hardlymovingpro 2 года назад
Wow! That's big bucks for less than 3 hours of work!
@corysabia8398
@corysabia8398 2 года назад
@@hardlymovingpro Yes because they pull the fuel injectors out of the engine also claim cant be done with them in their
@jamesgrady1421
@jamesgrady1421 9 месяцев назад
$850!! I wish my dealership charged me that little. My dealer tried charging me $1565 in labor $100 for parts. Then another $225 in labor to change the spark plugs (oh another $120 for parts). All in all it was gonna be $2600 for valve cover gasket, spark plugs and ignition coils. I told them ill do it myself. This video is awesome help! Glad I didnt spend the money with them.
@hardlymovingpro
@hardlymovingpro 9 месяцев назад
It's a pattern I'm noticing with auto repair quotes as more people choose to hold onto their cars instead of trading in for a new one. There's the labor problem as well. No one wants to be a mechanic and the repair shops are overwhelmed with service demand.
@fattymatty823
@fattymatty823 15 дней назад
My Ford dealer quoted me $483 plus tax.
@pod9363
@pod9363 3 года назад
The audio in your videos are very enjoyable for some reason. Very satisfying.
@hardlymovingpro
@hardlymovingpro 3 года назад
Thanks! I don't know ... Some people have said I have a pleasant voice?
@GelineDizon2025SlammersECNL
@GelineDizon2025SlammersECNL 2 года назад
My dad wanted to say thank you for posting this video..
@hardlymovingpro
@hardlymovingpro 2 года назад
Glad you found it useful!
@MatthewoMoSmith
@MatthewoMoSmith Год назад
These are the kinda videos that save me 1000s of dollars
@hardlymovingpro
@hardlymovingpro Год назад
Thanks! Need more guys like you with your attitude!
@enricoluca6781
@enricoluca6781 Год назад
Thanks. I stripped everything off the top of the valve cover and removed the fuel rail to find that quite a big part of one of the O-rings had broken off.
@hardlymovingpro
@hardlymovingpro Год назад
That's not good.
@smtnag
@smtnag Год назад
Awesome video. Best repair video I've seen in a while
@hardlymovingpro
@hardlymovingpro Год назад
Thanks 👍
@repairitdontwreckit4257
@repairitdontwreckit4257 10 месяцев назад
Excellent video. Very well produced. As others have said informative and to the point. I really like the tips on the electrical connections as they can be a bear to figure out. My valve cover isn’t leaking yet but when the time comes this video will be essential to my success. Thanks. Roger
@hardlymovingpro
@hardlymovingpro 10 месяцев назад
Glad you enjoyed it!
@robertgarrett7007
@robertgarrett7007 2 года назад
Thanks for the great video, sir. You are a professional at your job! (I’ve seen a lot of wannabe mechanics).
@hardlymovingpro
@hardlymovingpro 2 года назад
Thanks 👍
@BigJBlizzle
@BigJBlizzle Год назад
Excellent video my dude!! Speed thru the BS and showed us what and where is what......
@hardlymovingpro
@hardlymovingpro Год назад
Glad you enjoyed!
@The_pipeliner
@The_pipeliner 6 месяцев назад
Those plugs for the coil pack and assorted sensors are designed to be pressed from the top, not pried from the bottom. If you push the plug in and press the top of the tab in, it will come off pretty easy. Just FYI. Great video!
@hardlymovingpro
@hardlymovingpro 6 месяцев назад
Thanks for sharing!
@richard1835
@richard1835 2 года назад
Appreciate the video. Got a 2014 coming Thursday. Valve Cover Gasket. Thank you
@hardlymovingpro
@hardlymovingpro 2 года назад
Good luck!
@scottydavis1813
@scottydavis1813 2 месяца назад
I finally did this today on my 2013 Ford Fusion. It seems to be very loud and I forgot to put the foam stuff back under the fuel rail so not sure if that is it. I did have a misfire code and it could be a bad coil but it has me worried . I just quit for the day and will make sure everything is hooked up and maybe unplug the coils one at a time. It was not a pleasant job and I appreciate the video
@hardlymovingpro
@hardlymovingpro 2 месяца назад
Thanks for sharing. The foam is used as a noise dampener.
@scottydavis1813
@scottydavis1813 2 месяца назад
@@hardlymovingpro My car had a broken MAP sensor and a bad coil. I got it done today and it has never been so smooth. My wife complained of poor mileage so I think the MAP sensor has been broken awhile. I really hope you know how much I appreciate your video. We need that car and I cant afford all the labor. I would watch you do something then go do it. I am in your debit
@hardlymovingpro
@hardlymovingpro 2 месяца назад
You bet and thanks for sharing!
@Goodpeople787
@Goodpeople787 Год назад
Thank you just replaced mines using your video as a reference ❤
@hardlymovingpro
@hardlymovingpro Год назад
Glad it helped!
@TheLwillson
@TheLwillson Год назад
Very good video , thank you. Followed step by step perfectly .
@hardlymovingpro
@hardlymovingpro Год назад
Glad it helped!
@henrygallardo1969
@henrygallardo1969 Год назад
Thank you for your video. Very informal did my own gasket with your help!
@hardlymovingpro
@hardlymovingpro Год назад
Good for you!
@slickrick4216
@slickrick4216 2 года назад
Just changed my valve cover gasket in my 2013 1.6 Escape. Thanks for your very detailed video, it was so helpful!
@hardlymovingpro
@hardlymovingpro 2 года назад
You bet!
@joeshafer881
@joeshafer881 2 года назад
Great video man saved me a lot of time. I do recommend anyone doing this job to replace the o ring on the injectors were fuel rail connects to them. I did this at 90k and when went back together sprayed gas.. o rings were faulty and too playable. They are supposed to be hard o rings and yes they are expensive. I suggest rock auto. But the o ring will be the biggest worry for anyone doing this job. I recommend replacing them right off the bat. Just trying to pay it forward. Thanks for the video bro very easy to follow. I would also recommend replacing the cam follower as well on the high pressure fuel pump. If not replaced every 60 k I guarantee you will blow your engine... it's called a cam follower or bucket for the high pressure fuel pump on exhaust cam. I did that during this job as well 10 bucks off rock auto. Easy to install when your right there during this job
@hardlymovingpro
@hardlymovingpro 2 года назад
Thanks for sharing your valve cover gasket replacement experience! Never had problems re-using o rings as long as I coated them first with silicone grease as well as coating it's contact plugs. But nothing wrong with replacing them with new ones. Interesting recommendation on replacing the cam follower and the hp fuel pump. What causes these to fail and lead to engine damage?
@billw2812
@billw2812 2 года назад
The wrong or oldwayoverdue oil. The extreme pressure additive for these is the D in Dexos.
@jonathonklimmer6698
@jonathonklimmer6698 Год назад
Indeed that was a great very informative instructional video without any useless banter like some other videos and the camera angles were spot on. How long do you figure this took from start to finish? May be doing one in the future month. Thanks
@hardlymovingpro
@hardlymovingpro Год назад
Thanks! I'd say around 3 hours.
@stevejared2254
@stevejared2254 Год назад
Thank you for the clear concise video. God bless!
@hardlymovingpro
@hardlymovingpro Год назад
You're welcome.
@jesusxocua1787
@jesusxocua1787 Год назад
Very good video and very good tips. Thank you very much for sharing your knowledge. GOD bless you 🙏🏽
@hardlymovingpro
@hardlymovingpro Год назад
Glad you found it helpful!
@dylana2880
@dylana2880 10 месяцев назад
You saved my life. Thank you
@hardlymovingpro
@hardlymovingpro 10 месяцев назад
Glad the video helped you out!
@BillyBeer-su8zv
@BillyBeer-su8zv 4 месяца назад
Like the video. Going to see how much mechanic charges in town but I’ll probably end up doing it. Only question I have is how do you get the oil out of the spark plug holes(2 of them)? One was full pretty well. I also put new spark plugs in before realizing oil leak. Do I have to change those new spark plugs after they were in oil? Thanks.
@hardlymovingpro
@hardlymovingpro 4 месяца назад
Using a combination of compressed air and brake clean solvent to blow the excess oil out of the sp tube hole. After removing the old plug, a little residual oil leaking into the combustion chamber won't matter much.
@osvaldomendozagarcia9432
@osvaldomendozagarcia9432 2 года назад
You are the best
@hardlymovingpro
@hardlymovingpro 2 года назад
Thanks!
@Cam-wi3tp
@Cam-wi3tp 2 года назад
god i miss the good old days..
@hardlymovingpro
@hardlymovingpro 2 года назад
It is what it is
@MrWhite0
@MrWhite0 Год назад
Brilliant video thank you great detail 👍
@hardlymovingpro
@hardlymovingpro Год назад
Glad you enjoyed it!
@ATVPRO11
@ATVPRO11 Год назад
Excellent vid. Perfectly done ✅
@hardlymovingpro
@hardlymovingpro Год назад
Glad you liked it!
@chops1sc
@chops1sc Год назад
Very helpful video! Thank you!
@hardlymovingpro
@hardlymovingpro Год назад
You're welcome!
@KalvinVerner
@KalvinVerner Год назад
THANK YOU FOR THIS VIDEO!!!!
@hardlymovingpro
@hardlymovingpro Год назад
You bet!
@TavosMr
@TavosMr 3 года назад
Very knowledgeable and professional work.👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻.
@hardlymovingpro
@hardlymovingpro 3 года назад
Thanks!
@BillyBeer-su8zv
@BillyBeer-su8zv 4 месяца назад
Also did you use dielectric(spelled wrong probably)grease throughout the video? I noticed at times you said silicone grease. Just making sure I apply right grease throughout. Thanks.
@hardlymovingpro
@hardlymovingpro 4 месяца назад
Di-electric is silicone grease. Also called plumber's grease.
@kousinkoolaid
@kousinkoolaid 25 дней назад
Can’t say thanks enough.
@hardlymovingpro
@hardlymovingpro 25 дней назад
You bet!
@AutoRestoMod
@AutoRestoMod 2 года назад
Nicely done video!
@hardlymovingpro
@hardlymovingpro 2 года назад
Glad you liked it!
@sidewayzmike
@sidewayzmike 11 месяцев назад
Im about to dive into this today. My moms car has a broken spark plug to extract! I guess those ole triton spark plug "train wrecks" carried over to the 4 cylinders 😂
@sidewayzmike
@sidewayzmike 11 месяцев назад
I like the celaphane under the cap trick, for opened tubes of rtv
@hardlymovingpro
@hardlymovingpro 11 месяцев назад
Yup. Keeps the RTV from drying out
@hardlymovingpro
@hardlymovingpro 11 месяцев назад
Not aware the plugs break on these engines
@sidewayzmike
@sidewayzmike 11 месяцев назад
Well. Let me start by saying, vehicle was bought used with under 20k, from CarMax. Car now has 70k. She recently got misfire on cyl 3, so I decided easy enough, threw a coil at it, that did nothing. So, orders up a set of plugs. Number 3 was going to be last, so I r&r #1 and #4, they came out as they should. Number #2 was a Trainwreck, I ended up idling the car for 20 min intervals, and applying wrench to "nurse" it out. It was a real bear. But, I got it out. That #2 showed the threads similar to cross threading, but I really think maybe dissimilar metals in combination with forced induction, maybe something else. Anyways, chased the threads and installed that new plug. Moved onto number #3 (initial misfire hole), and did the same process of heating the engine then breaking out tools to work that one loose. IT BROKE, AND LEFT ABOUT 100% of the plugs threads, in the head. I've done service and repair for greater than 25 years,and never broke a plug until now.
@sidewayzmike
@sidewayzmike 11 месяцев назад
I needed your video, to familiarize myself with how much space I can gain, accessing the extraction, with valve cover off. That's how I found ya, lol 😅
@anthonymartin916
@anthonymartin916 Год назад
Great Job!!
@hardlymovingpro
@hardlymovingpro Год назад
Thanks!
@enricoluca6781
@enricoluca6781 Год назад
Great video. It is both concise and professional. I replaced my valve cover recently and did not torque it down. Would have done so if I had a decent torque wrench. Unfortunately I thought I could get away without replacing the injector o-rings. After assembling everything and running the car for a couple of minutes I noticed a strong smell of petrol and sure enough there was a big pool of petrol on the garage floor. I had tightened the fuel line using the 17 mm ring spanner and thought I had been fairly firm with it. What is likely to be the source of the leak? Could there be a 3rd possibility, that I had broken and injector (although I guess it wouldn't have run properly if that was the case)
@hardlymovingpro
@hardlymovingpro Год назад
Believe its an injector O ring that slipped off. That's why I always coat the O ring and the O ring cap with silicone grease so that the ring slips in place.
@katerinmorales6333
@katerinmorales6333 Год назад
@@hardlymovingpro hello
@Delrondae
@Delrondae Год назад
What was the torque specs for the fuel rail ? My car isnt getting any gas to it after i put everything back together
@hardlymovingpro
@hardlymovingpro Год назад
They're only 10mm fastener bolts that require 10 or less lbs of torque which isn't a lot. I'm going to guess that the fuel rail O rings are not seated properly and you're leaking fuel.
@davidr.miller5171
@davidr.miller5171 2 года назад
Thanking for the information. Next question. Can I use a standard o ring for the VVT.
@hardlymovingpro
@hardlymovingpro 2 года назад
If it doesn't swell if exposed to oil.
@Gabriel_chicken
@Gabriel_chicken Год назад
i just ordered a valve cover and gasket due too a leak,not sure which is the problem so i have both on order,while waiting on them could you tell me the size of o rings replaced or the names of the parts that require them ,and your video is great thanks.
@hardlymovingpro
@hardlymovingpro Год назад
The valve cover gasket should come with new o rings.
@Narcotiqs
@Narcotiqs 4 месяца назад
Man great work. Can you do this to my escape? Probably cost me 2k at the dealer
@hardlymovingpro
@hardlymovingpro 4 месяца назад
Shouldn't be that much. We're talking about 3 hours of labor.
@noelramirez786
@noelramirez786 6 месяцев назад
Besides the injectors orings, what are the other 2 orings called? The ones you replaced in the left side by the oil feeding cap? Looks like sensors maybe? Thanks
@hardlymovingpro
@hardlymovingpro 6 месяцев назад
It came with the FelPro gasket replacement kit. Believe they're O rings for the camshaft solenoids.
@shannonbradley963
@shannonbradley963 3 года назад
Very efficient. What kind are the extra long wrenches your using? Also have you had good luck with the aftermarket m12 batteries ? Can't tell what they are. Thanks !
@hardlymovingpro
@hardlymovingpro 3 года назад
I use Milwaukee's M12 3/8" electric ratchet and impact gun. The aftermarket batteries work fine.
@hermgreen7183
@hermgreen7183 4 месяца назад
How did you get the clips over the fuel rail? Your supposed to pull the injectors
@hardlymovingpro
@hardlymovingpro 4 месяца назад
Injectors stay on the engine block. Unbolt the fuel rail and line and you can remove fuel rail as shown in the video.
@Slit-throat
@Slit-throat 10 месяцев назад
Ouch. I just did this and i didnt know i needed to put gasket maker at the little corners...
@hardlymovingpro
@hardlymovingpro 10 месяцев назад
May not leak too bad.
@scottydavis1813
@scottydavis1813 2 месяца назад
I have one more question sir, just before you showed the black tube of RTV what was the 2 things you installed new o-rings on? I need to get those and I will have all I need. I didn’t see them in the injector o-ring kit. Thank you
@hardlymovingpro
@hardlymovingpro 2 месяца назад
Camshaft position sensors.
@scottydavis1813
@scottydavis1813 2 месяца назад
@@hardlymovingpro I really appreciate you sir
@hardlymovingpro
@hardlymovingpro 2 месяца назад
You bet!
@steviedwalls
@steviedwalls 9 месяцев назад
You’re the man!!!! Thanks for
@hardlymovingpro
@hardlymovingpro 9 месяцев назад
Happy to help!
@elmexa1
@elmexa1 2 года назад
Thank you, I was about to pay $350 to a local mechanic.
@hardlymovingpro
@hardlymovingpro 2 года назад
Wow! Big bucks.
@thec-house8078
@thec-house8078 Год назад
Cleanest repair , this should work on any 1.6ecoboost?
@hardlymovingpro
@hardlymovingpro Год назад
Yes it should.
@fabioh2826
@fabioh2826 Год назад
great video , thanks sr
@hardlymovingpro
@hardlymovingpro Год назад
Glad you liked it!
@frankoros4438
@frankoros4438 3 года назад
Awesome video! I have a leaky gasket also. Can you please tell me where you purchased the gasket kit. I can't seem to find one with the o rings included. Thank you for the video.
@hardlymovingpro
@hardlymovingpro 3 года назад
Try rockauto.com
@petervargas2306
@petervargas2306 2 года назад
Thank you for the video extremely helpful. I just finished mine but now I have a misfire in 3 cylinders. When I pull the rail 3 injectors came out and that the 3 I have a misfire. I replace the orIngs. Thank you
@hardlymovingpro
@hardlymovingpro 2 года назад
If there's a problem with any of the o rings, you experience fuel leakage.
@mechanicjose4023
@mechanicjose4023 2 года назад
It's direct injection... The tip of the injector that faces the block has a Teflon seal that need to be sized up by seal sizer from Ford. The green o- ring that faces the fuel rail those get lubed with a little bit of oil. But the Teflon seal has to go in dry with no lubrication..... If you don't follow the correct for installing Teflon seals on direct injection you will get a misfire... The car in the video got lucky that they got stuck in the block and only had to replace the green o- rings
@omerta2588
@omerta2588 Год назад
Yeah I ripped 3/4 injectors out with the rail. Immediately knew I was screwed... Went ahead and tried to seat em back into the cylinders as snug as possible, but yeah I can hear and smell fuel spitting when the fuel pump charges the rail. Throwing codes. Won't even start today. Completed the install yesterday... So idk what in the hell I need to do at this point. Pisses me off. Clusterfuck of an engine... I've overall had good luck up until this point, but she ain't liking life right now that's for sure...
@hardlymovingpro
@hardlymovingpro Год назад
Get new o rings, if damaged/torn, lubricate with dielectric grease then reinstall. The grease will noticeably ease installation.
@omerta2588
@omerta2588 Год назад
@@hardlymovingpro yessir. Gonna try and get replacement kit to replace all o-rings and the Teflon seals. Can get a kit for dry fitting those Teflon seals as well I think. Thanks 👍🏻
@anthonymartin916
@anthonymartin916 9 месяцев назад
Great video!!!!
@hardlymovingpro
@hardlymovingpro 9 месяцев назад
Thanks!
@scottydavis1813
@scottydavis1813 2 месяца назад
Do they make a kit that has all those o-rings?
@hardlymovingpro
@hardlymovingpro 2 месяца назад
If referring to the fuel injectors, yes.
@emmanuelcarrion5168
@emmanuelcarrion5168 3 года назад
Nice! I recently did a valve cover gasket on a hyundai entourage 3.8l. Huge compared to this one lol
@hardlymovingpro
@hardlymovingpro 3 года назад
Pain taking off the plenum?
@emmanuelcarrion5168
@emmanuelcarrion5168 3 года назад
@@hardlymovingpro no not really. Just got to remove a few wire harnesses out of the way. The front of the intake plenum has this metal bracket I had to take off so I can clear the engine oil dipstick and the metal brace that goes above the radiator
@hardlymovingpro
@hardlymovingpro 3 года назад
@@emmanuelcarrion5168 Ok
@halleffect1
@halleffect1 Год назад
thanks, great video
@hardlymovingpro
@hardlymovingpro Год назад
Glad you liked it!
@frallos
@frallos 3 года назад
Thank you for sharing!
@hardlymovingpro
@hardlymovingpro 3 года назад
You bet!
@richard1835
@richard1835 2 года назад
Great job!!
@hardlymovingpro
@hardlymovingpro 2 года назад
Thanks!
@gustavomaguina40
@gustavomaguina40 Год назад
Thanks for video
@hardlymovingpro
@hardlymovingpro Год назад
You bet!
@SleepFaster18
@SleepFaster18 Год назад
I am having trouble telling if the coils are seated properly, how do I know they are on the spark plugs well enough?
@hardlymovingpro
@hardlymovingpro Год назад
If there's no misfire after starting the car.
@toderickgellingtonjr6590
@toderickgellingtonjr6590 2 года назад
Great video exactly what I was looking for only thing is I fucked up changing my spark plugs i over tightened the coil pack that goes in to the lil gold nut holder idk what it’s called n now it’s stripped n I’m not getting any spark from spark 2 due to the lil type gold cap being stripped went to multiple auto shops said they don’t sell em what is the top piece u took off called
@hardlymovingpro
@hardlymovingpro 2 года назад
If you overtorque a coil pack bolt, the bolt will force the brass retention nut recessed in the valve cover to spin. Only way to get the nut off is to cut the head of the bolt off with a small rotary cut off disc (i.e. dremel tool). You may have to replace the valve cover because of this damage or find a way to brace the coil pack down.
@toderickgellingtonjr6590
@toderickgellingtonjr6590 2 года назад
@@hardlymovingpro I have a 14 fiesta st but it has the same engine appreciate you u know where I can find a valve cover or what’s the part number
@Mattholl847
@Mattholl847 Год назад
What are the metal cylinders you have to take out on the left side I still have an oil leak in the top left corner and I just replaced the gasket. I’m not sure if that need replacing. 4:26
@hardlymovingpro
@hardlymovingpro Год назад
Those are the intake and exhaust camshaft solenoids. They're exposed to oil and harden o ring seals could be a source of oil leakage. Good practice to replace them.
@juanmiranda4521
@juanmiranda4521 3 года назад
Great job
@hardlymovingpro
@hardlymovingpro 3 года назад
Thanks!
@amm9933
@amm9933 2 года назад
Hey so if the fuel injector does come out do you need to replace the Teflon seal on the bottom of the injector? The new seals came with the kit but the sizing tool (303-1567) is $150. Just wondering if that's mandatory before buying a tool I'll use once
@hardlymovingpro
@hardlymovingpro 2 года назад
In this video I only remove the fuel rail from the injectors and I used the existing o rings. No need to remove the injectors from the engine.
@machariomoreno5110
@machariomoreno5110 2 года назад
Did you clean the spark plug well after the gasket repair? Or did you just let it burn out?
@hardlymovingpro
@hardlymovingpro 2 года назад
Just a minor amount of oil. Let it burn out.
@ChristianFleming-oi6wg
@ChristianFleming-oi6wg Год назад
Do I need to depressurize the high pressure fuel pump and fuel rail by disconnecting the fuel pump fuse in order to do this job?
@hardlymovingpro
@hardlymovingpro Год назад
No need to remove the fuse. Place a rag under the fuel rail flare nut and loosen the nut. Residual fuel pressure will release a small amount of fuel and that's it.
@ChristianFleming-oi6wg
@ChristianFleming-oi6wg Год назад
Thank you!
@geraldoramos6312
@geraldoramos6312 2 года назад
I have the same problem my gasket is leaking what will a fair price to repair at a mechanic shop I should pay ?
@hardlymovingpro
@hardlymovingpro 2 года назад
Not more than 3 hours labor + cost of parts
@JoeSpivey2
@JoeSpivey2 7 месяцев назад
Do you have a part number for the vvt o-rings?
@hardlymovingpro
@hardlymovingpro 7 месяцев назад
O rings came with the Fel Pro gasket kit. Link to the kit provided in this video's description area.
@EmanuelCruz7
@EmanuelCruz7 Год назад
Donde tiene su taller amigo?
@hardlymovingpro
@hardlymovingpro Год назад
Al este de Memphis, Tennessee.
@EmanuelCruz7
@EmanuelCruz7 Год назад
@@hardlymovingprocuánto cobra usted por cambiar el empaque de los cilindros, mi Ford escape 2013 está gastando líquido refrigerante por eso y tiene el cilindro 1 bloqueado
@EmanuelCruz7
@EmanuelCruz7 Год назад
@@hardlymovingpro ahora llevo una hora de carretera y me dice (temperatura de motor alta pare con cuidado)
@noelramirez786
@noelramirez786 6 месяцев назад
Cual era el problema y cuanto te costo arregarlo? Gracias
@machariomoreno5110
@machariomoreno5110 2 года назад
A problem I had with this engine is the fuel injectors were loose. Are they supposed the be loose? I have white smoke coming from the engine but no overheating and no milky oil, so im assuming the fuel injector seals are bad? Im also assuming the smoke is coming from the fuel injector seals since they are loose? Anyway i could send you a video through email for help?
@machariomoreno5110
@machariomoreno5110 2 года назад
Did you also replace bottom o ring for fuel injectors?
@hardlymovingpro
@hardlymovingpro 2 года назад
Injectors are held in place via the fuel rail. The o rings are there to prevent fuel leakage. Without the fuel rail attached the injectors will wiggle around. White smoke could be muffler water heat evaporation during cold morning startups.
@raffamichael7460
@raffamichael7460 Год назад
Where did you buy the kid at for the gaskets to change the valve cover gaskets
@hardlymovingpro
@hardlymovingpro Год назад
Any auto supply retailer.
@mikescot7187
@mikescot7187 2 года назад
Awesome!👍👍
@hardlymovingpro
@hardlymovingpro 2 года назад
Thanks!
@willielittle5307
@willielittle5307 6 месяцев назад
What was your charge to do thosbqith parts and howblongvdid it take you
@hardlymovingpro
@hardlymovingpro 6 месяцев назад
Charged for 3.5 hours and $30 parts.
@willielittle5307
@willielittle5307 6 месяцев назад
What is your hourly rate and location
@hardlymovingpro
@hardlymovingpro 6 месяцев назад
East of Memphis, TN
@davidr.miller5171
@davidr.miller5171 2 года назад
What brand of Fuel Injector o ring did you use on the 2014 Escape fuel rail (TOP). 1.6 LTR Engine
@hardlymovingpro
@hardlymovingpro 2 года назад
Doesn't matter. It's low tech. Get Motorcraft or Mahle.
@AngelPHK94
@AngelPHK94 2 года назад
quick question ... this my first time working on this car .. I was going to do a simple spark and coil change then realize 3 out of 4 coil where slightly wet with motor oil ... that to me is a quick sign of a worn spark plug tube seal!!! after watching you work i didnt see any tube seals .... do u know y my coil is slightly wet with oil.... could if be the valve cover gasket tht bad???? or do i have to keep opening to reach the tube seals????
@hardlymovingpro
@hardlymovingpro 2 года назад
Leakage from the cover gasket can migrate to the AP tubes.
@AngelPHK94
@AngelPHK94 2 года назад
@@hardlymovingpro so there's no spark plug tube seals on this car?? so my issue is the valve cover gasket itself ?? thank you so much dude .. great vid btw!!!
@elgmac73
@elgmac73 3 года назад
did you removed the fuel line fuse and burn any fuel left in the system before removing the injectors ?
@hardlymovingpro
@hardlymovingpro 3 года назад
Nope. Not very much residual pressure.
@19f97
@19f97 2 года назад
Do I really need to replace the vvt solenoid o-rings as you did? Where did you source them?
@hardlymovingpro
@hardlymovingpro 2 года назад
The new o rings came with the Fel Pro gasket replacement kit.
@Usmanthemecano
@Usmanthemecano 3 года назад
Wheeew what a pita job!! What's the labor hour?
@hardlymovingpro
@hardlymovingpro 3 года назад
Around 3. Next time, around 2 or less.
@ShiznitDaShiz
@ShiznitDaShiz 2 года назад
My question is why does alldata say i need a heat gun to remove the valve cover gasket? Thats the only thing that has stopped me from doing mine. Any info please. Thanks
@hardlymovingpro
@hardlymovingpro 2 года назад
Doesn't make that much sense to me either. Just don't be too aggressive braking the gasket seal loose from the cylinder head. Pry valve cover corners with wide tip a few driver.
@ShiznitDaShiz
@ShiznitDaShiz 2 года назад
@@hardlymovingpro awesome thanks for the reply.
@josecastelar3306
@josecastelar3306 Год назад
Hey what’s the name of that red handle tool you used to pinch the hose clamp? I would appreciate it!
@hardlymovingpro
@hardlymovingpro Год назад
They're called hose clamp pliers. I provided a link to a set in this video's description.
@machariomoreno5110
@machariomoreno5110 2 года назад
Okay thank you, and do you have the part number for the fuel injector o rings and vvt? The fuel injector o rings look a bit pricey for something that small? Referenced from Autozone Fel-Pro es73118. And should you buy new coil packs as well?
@hardlymovingpro
@hardlymovingpro 2 года назад
The Felpro gasket kit came with new vvt o rings. I re-used the FI o rings. I only replace coil packs when they fail.
@davidoldert9552
@davidoldert9552 2 года назад
It seems one can't order OEM VVT solenoid o-rings separately, only new solenoids (which come with o-rings). Volvo solenoid part nos. for reference are: 36010300 (intake) and 36011316 (exhaust). This is for the B4164T engine, which I think is the one in the vid. I don't know the Ford part nos. @Hardly Moving Productions, would it be possible to get a spanner under the solenoids so that they needn't be removed?
@dam.mdj953
@dam.mdj953 Год назад
After changing the gasket i have p132b fault od turbocharger. What should i check? 1.6 ecoboost 160hp mondeo mk4
@hardlymovingpro
@hardlymovingpro Год назад
Check for air hose vacuum leaks with all your hoses and your air intake tube leading to the turbo.
@dam.mdj953
@dam.mdj953 Год назад
@@hardlymovingpro thanks for answer. No leaking. Only a damaged Valve of vacuum pump(Orange silicone membrane destroyed). What can i do bad during changing a valve cover gasket that can cause a p132b error and a loss of power...
@davidr.miller5171
@davidr.miller5171 Год назад
Did you pull out Fuze F56 to depreasure the fuel system??
@hardlymovingpro
@hardlymovingpro Год назад
Nope.
@ICEMANdrake214
@ICEMANdrake214 2 года назад
Hello I hope you see this comment. I followed your video and something went wrong for me. I replaced the valve cover, spark plugs, and boots but now my car cranks but struggles to start. When it does start it doesn’t stall or anything but it has a very strong gas smell the whole time I drive, my mpg has tanked, and it’s throwing a P00C6 code (fuel rail pressure low). One thing that happened when I pulled out the fuel rail a fuel injector from cylinder 3 came with it, and some gas got down into the connector for the cylinder 1 injector. Some help would be greatly appreciated. I can’t find anything online that narrows it down. Thanks
@hardlymovingpro
@hardlymovingpro 2 года назад
More than likely the o ring in one of your injectors is damaged.
@billmytko8398
@billmytko8398 3 года назад
Great vid. How long did the job take?
@hardlymovingpro
@hardlymovingpro 3 года назад
With the learning curve, around 3 hours.
@billmytko8398
@billmytko8398 3 года назад
@@hardlymovingpro Just finished mine. thanks for the video again....
@hardlymovingpro
@hardlymovingpro 3 года назад
You bet!
@hugocontreras7515
@hugocontreras7515 3 года назад
Hi I have a 1.6 where would the oils be coming from if my spark plugs have some in there
@hugocontreras7515
@hugocontreras7515 3 года назад
What gasket is leaking
@hardlymovingpro
@hardlymovingpro 3 года назад
Maybe from the coil pack tube gasket.
@user-ub8cc8to2y
@user-ub8cc8to2y 7 месяцев назад
USING DIELECTRIC GREASE , WHILE I , AS AN AUTO TECH DO USE IT ON COOLING SYSTEM HOSES AND ORINGS ETC, I MIGHT POINT OUT THAT SILICONE CAN POISON OXYGEN SENSORS UNLESS YOU USE SILICONE LABELED AS OXYGEN SENSOR SAFE. FOR THAT REASON I PERSONALLY NEVER USE DIELECTRIC ON ANYTHING RELATED TO THE ENGINE OR INTAKE SYSTEMS. MAYBE IM MISTAKEN BUT THAT IS MY APPROACH.
@hardlymovingpro
@hardlymovingpro 7 месяцев назад
Thanks for sharing! In oxygen sensor threads, I use copper anti seize.
@corysabia2141
@corysabia2141 2 года назад
9/16 socket is size for the spark plugs goes in easy
@hardlymovingpro
@hardlymovingpro 2 года назад
Or 16 mm. Thanks for sharing!
@gustavogonzalez9011
@gustavogonzalez9011 3 года назад
do the o rings for the fuel injectors come with the valve cover gasket set?
@hardlymovingpro
@hardlymovingpro 3 года назад
Nope
@MetalForEmmanuel
@MetalForEmmanuel 2 года назад
Great video. Just followed your instructions and when I took the fuel rail off one of the fuel injectors came out with it. I took it off and put it back in it's hole. Finished the job and when I started it up its running pretty bad. Skipping pretty bad. I checked the spark plug and it's covered with gas. Cleaned it off and put it back. Let it run for a minute and still skipping. Checked the same spark plug and it's covered with gas again. Is something not seated properly?
@hardlymovingpro
@hardlymovingpro 2 года назад
Check all fuel line connectors for tightness. Check that the injectors has a its O ring both top and bottom.
@n5980
@n5980 2 года назад
Did you resolve this? I’m having the same problem.
@MetalForEmmanuel
@MetalForEmmanuel 2 года назад
@@n5980 I made sure everything was seated properly and just let it run for a bit. It evened out and is running fine. Haven't had any problems for months.
@dealerauctionnightmare4689
@dealerauctionnightmare4689 Год назад
Wondering why you removed the VVT solenoids?
@hardlymovingpro
@hardlymovingpro Год назад
Got in the way to remove the cover.
@dealerauctionnightmare4689
@dealerauctionnightmare4689 Год назад
@@hardlymovingpro I see what you mean. They cover a few bolts.
Далее