FZ-07 Chain Slack, How to Tighten Chain, Yamaha MT07/FZ07 Chain Slack

Подписаться 4,7 тыс.

Просмотров 150 тыс.

50% 1

FZ07 How to tighten fz-07 and mt-07 chain slack. FZ-07 Maintenance adjusting the chain slack. Proper chain slack is important. Proper chain slack on fz07 yamaha.
TAGS: FZ07 FZ-07 MT07, MT-07 Chain Slack MT-07, Chain fz07 & mt07, adjusting chain on FZ-07, measure chain slack, how to FZ-07 MT-07, how to adjust chain.
www.moto-merica.com
2015-2016 Yamaha FZ07 MT07
How to video - adjusting chain slack on z07 yamaha
Please Subscribe:
www.youtube.co...
Riding Review- Givi Windscreen
• FZ-07 Givi Windscreen ...
Is FZ-07 A Good Beginner Bike?
• Is FZ-07 A Good Beginn...
Yamaha FZ-07 New Bar End Mirrors
• Yamaha FZ-07 New Bar E...
FZ 07 Storage -"FZ-07 Storage Trunk"
• FZ-07 Trunk "FZ 07 Sto...
Yamaha FZ-07 Dash Review!
• "Yamaha FZ-07 Yamaha M...
Yamaha FZ-07 Pros and Cons review
• Yamaha FZ-07 Pros and ...
FZ-07 / MT-07 Test Ride Review
• Yamaha FZ-07 First Rid...
Shoei GT Air Helmet Review!
• SHOEI GT AIR HELMET RE...
Ebay bar end mirrors upgrade for fz07 & mt07
• "BAR END MIRRORS FZ-07...
FZ-07 Givi Windscreen install.
• FZ-07 Givi Windscreen ...

Опубликовано:

1 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 141

@MotoMerica 5 лет назад

Good sockets to have around for the bike are 27mm for rear axle nut, 19mm for the front axle, 17mm for the oil drain plug. Double check these before purchasing.

@nareemhart8710 2 года назад

Exactly what i wanted. thankyou, sincerely the idiot who stored his manual in an open backpack...

@Dannitrade Год назад

That s what I searched for bro, the nut size😂

@Dannitrade Год назад

@@nareemhart8710in the Manuel there is no info of the nut sizes

@Leviweyhrich 4 месяца назад

@@Dannitrade Who is Manuel?

@graydation 8 лет назад

Never loosen with a torque wrench.

@MotoMerica 8 лет назад

Yeap someone else said the same thing. I never knew that it could damage but I will use breaker bar next time. Thanks for watching and the comment.

@VanderBori 8 лет назад

Why?

@graydation 8 лет назад

Kaan Acurol from what I was told when I was an aircraft mechanic for the Air Force... it can mess up the calibration... but I admit that was years ago... but unless something has changed with torque wrench technology over the years... I would stick with that. Or you could just Google it these days...lol

@VanderBori 8 лет назад

oh I didn't know. Although when I was worked in calibration lab. :) Thank you for this knowledge.

@roslimaimon9176 7 лет назад

Joe Gray pmin

@MrBennyb 7 лет назад

That chain way to tight

@tompeter7326 4 года назад

OMG, Guess the front sprocket bearing wont last to long with this over tightened chain. 4 half turns he he !

@PERLaLIFE 4 года назад

1. when tightening axlenut always push wheel forward as hard as you can ( pulling chain can help). 2.you need to check the axle slider position after you`ve tighnened the axle aswell to make sure its still correct. 3. You measured the chain tension WRONG, you should measure from the part of the plastic chain slider that sticks out the furthest from the swingarm, look closely in ur owners manual and u will see it for urself (meaning if u measure from actual swingarm it will be waaaay to tight.

@karlschauff7989 4 года назад

The manual says push down on the chain just below the end of the "chain drive guard" and the manual has a picture that's pointing to the plastic guard that's on the bottom side of the swingarm, which is where this guy was measuring at. His mistake was not holding the measuring tape perpendicular to the swingarm. It's definitely too tight because he measured 2" at an angle. He's probably running 1.75" if he had measured it correctly.

@theunluckycharm9637 5 дней назад

@@karlschauff7989BIG OOF

@Jaxxo11 6 лет назад

Nice vid! You should also remeasure the chain slack after you tighten the axle because it can also change a bit as well.

@MotoMerica Год назад

Yes good comment thanks

@migflc778 5 лет назад

you do not know how to check for chain slack sir. sorry

@Heavenascendedguy 8 лет назад

i thought chain slack was the distance in mm between lower position of the chain and the upper one , so the range of movement of the chaing up-down. if measured from swingarm you will never achieve a certain minimum slack ie , 10 or 20 mm.

@MotoMerica 8 лет назад

+Nil Gracia Moreno ... nope check your manual. distance from lower edge of swingarm to center of chain when pressing down on chain needs to be 51-56mm

@Wabbit1961 6 лет назад

You'd be correct if the bike was older. That's how they USED to measure. Now they simplified it on this bike and probably all their current models. Mine's a 2018. It says basically 2"-2.2" measured from the bottom of the plastic chain guard to the top of the chain. But remember, the manual also says you should be pulling down on the chain when you measure. It's not a static measurement. You can still do it the old way but the distance the chain travels up, then down, is only about an inch and a half total movement. Still a safe bet this way as well.

@tdunster2011 4 года назад

@@Wabbit1961 The manual is poorly written. It fails to explain that you should stop pulling down when the top of the chain moves. Otherwise you will always end up with a chain that's way too tight.

@myhailomykytyn1360 2 года назад

OMG...se this video by accident. My chain is down over 3 inches already. Thanks man

@jasonthompson7803 5 месяцев назад

Is the axle nut a 27mm? I have a 24 Mt07 and it is due for a chain adjustment.

@xmax126 8 лет назад

Hey man, just letting you know that, as others have said, you need to measure from the bottom of the chain guide to the center of the chain. Look at page 7-23 number 4 and also look at the picture on the top right on page 7-24. We have the same manual and bike so it has nothing to do with different years.

@MotoMerica 8 лет назад

No worries man. I'm just showing you how I do mine. You should always do what you want to do. Thanks for the comment

@stigjensen4818 4 года назад

Yes 😉 you have to measure from the bottom of the plastic, it makes a difference. And better it's a bit to lose, then to tight, to avoid damage.

@MotoMerica 8 лет назад

How-to video showing how to adjust the chain slack on your Yamaha FZ-07 and MT-07 for 2015 and 2016 models. Enjoy!

@TheMrZlatko Месяц назад

You should measure from the drive chain guard, not the swing arm. You can see that in the manual.

@oliwillems72 2 года назад

Al things ur doing are wrong. Read the manual please

@MotoMerica 2 года назад

Thanks for watching.

@haydrian123 4 года назад

This video could've been 3 minutes...... Just get to the point. Do this, do that, ride your bike. That's it.

@danielfalin 2 года назад

tightened the chain too much, you did not measure the slack correctly and even measuring from the swing arm you were out of spec, be careful, over tightened chain is very dangerous, you can damage the gearbox driveshaft bearing, worst case the chain can snap and that can be catastrophic for you and for the bike. keep in mind, slightly loose chain is always better

@lovingmylifeasIage6741 2 года назад

I just cut a 2" peace of a wooden dowel and jammed it between the chain guard and chain to check the slack. The distance to the rivet on the chain link and the top of the chain should make it in tolerance. Mine has about 1600 miles on it and the chain is fine.

@MotoMerica 2 года назад

Whatever works for you - just do it. Thanks for watching. Enjoy your ride!

@robertmoore9941 Год назад

Thank you for such a informative video. I own a 2019 mt07 , I also wanted to complement on the pristine clean condition of your bike. Mine usually has grease cast off from chain lubrication thanks to your video I’ll know exactly what to do when adjusting my chain and while I do so I’ll get some degreaser and clean The sprockets and wheel 😷😎🤪👍

@kylebromley6066 3 года назад

Just picked up a 2021 mt07. I needed to adjust the chain and found your video helpful. I like your sliders. I'm looking for a full set. Where did you get yours from?

@MotoMerica 3 года назад

I'm sorry I dont remember but search the web you should be able to find them. Have fun riding your MT07

@Databyter 4 года назад

I realize this hasn't been commented on in a while, but a few things should be said. First, the measurement is from the upper GUIDE to the middle of the chain. NOT the bottom of the swingarm as you showed in SOME of your shots, like the first measurement. Second, when pressing down, the weight of your forearm is sufficient. You do not need to apply much force, just enough to pick up the slack and straighten out the chain. Third, regarding NOT using a torque wrench as someone asked below and MotoMerica correctly advised to borrow one if needed. The thing is, the axle nut has to be tight enough, and put the right pressure on the bearings for proper wear. If you over-tighten it not only will your bearings potentially be over stressed, but the axle nut itself is a multi-part nut, and it is designed to barely be able to survive the correct torque. If you over-torque your axle, you will ruin the axle nut, and may even have difficulty removing it to replace it. Databyter

@MotoMerica 4 года назад

Nice comments thanks for watching

@rtbt8185 2 года назад

Center of chain

@Databyter 2 года назад

@@rtbt8185 Good catch. Corrected.

@KarawrIB619 8 лет назад

Hey brotha! Been watching your videos for a while now. I'd say religiously ever since I got my own. Just picked it up on the 14th. Amazed by the bike so far and I cannot wait to master it. Thanks again for your insight on how the bike works. Your work and time is much appreicated. Ride safe!!

@MotoMerica 8 лет назад

+KarawrIB619 ...awesome comment and I do appreciate the words. It does take some time to make the videos - at least for me. I enjoy making them though so it's all cool. Enjoy your bike and congrats on the purchase. !!

@CLONEBF 6 лет назад

What’s the size of the axel nut?

@raineoffyre 6 лет назад

27mm I believe for the rear. Correct me if I'm wrong

@XouZ88 5 лет назад

6:24

@mugetz696 3 года назад

Arent you supposed the meassure it from the end of the rubber thingy by putting your tape thing on the lowest rubber part?

@wheeliehog6783 8 месяцев назад

Correct

@NJtriple7 2 года назад

Thank you for this video… I’m adjusting my chain for the first time and I have no idea what I’m doing

@dbest1aVlogs 8 лет назад

Doesn't seem your sure. 15inch pounds of force, how do you know ? Also you should turn the adjusting screw in smaller increments like maybe half turn each side, then check.. Hopefully it worked for you . You should double check it with a gauge that can exert the force on the chain when you can .

@MotoMerica 8 лет назад

+dbest1a Vlogs ...yep I was kinda joking around. it's good the way it is. Thanks for checking it out and commenting.

@dremyofit6719 8 лет назад

ty so much. FZ07'S videos are growing and your videos are one of my favorites.

@MotoMerica 8 лет назад

+don ervin ... Hey thanks man. I really appreciate that. I started with the idea it would help others by showing what I did to my bike (good or bad). As long as we get to ride that's all that matters.

@TofuProductionCinema 3 года назад

Probably the best video regarding motorcycle chain adjustment I've seen. I wouldn't loosen with tq wrench, but meh - nice work man!

@lukeneary5613 Год назад

Where did you get your torque wrench?

@NahBra 5 лет назад

size wrench for small nuts?

@Wabbit1961 6 лет назад

The manual also tells and shows you too pull DOWN on the chain. THAT'S the measurement. Not static measurement. Also, the top of the measure goes to the top of that plastic chain guard, NOT to the swingarm. Manuel says so. Do a 1/2 turn at a time both sides. When you over tighten you then have to back off and PULL the tire back to get rid of the slack. PITA to do.

@ikbendusan 5 лет назад

manuel XDDDD

@woodknack1 Год назад

You have that chain way too tight. You also want to roll it around and check it. You are putting up a video that newbies think is the right way to do it, when in fact it is not!

@user-ot1dv6ri4f 6 месяцев назад

Don't forget to check the chain slack at different chain positions because they stretch unevenly across the length of the chain

@TheJohnVancouver 9 месяцев назад

Is the dumb ass alignment indicator on the right swing arm replaceable/removable?

@mullenli Год назад

You shouldn’t use the torque wrench to lose rear axle nut . Good clips though Thank you .

@nothingman3542 2 года назад

Had to comment, just tightened mine. Great instructional how to. Well done.

@MotoMerica 2 года назад

Thanks for watching.

@guillaumecarrier3700 7 лет назад

Got an issue with mine. When I try to loosen the chain on the chain ajuster on the right side, the adjusting nut moves freely without moving the axle towards to front to loosen the chain. (But when I tight the chain, it works). So the adjusting nut move freely so that I can actually remove the gray backplate. On the left side everything is normal when I try to loosen the chain it works and move the axle. Any idea?

@MotoMerica 7 лет назад

Check the manual to make sure correct also

@guillaumecarrier3700 7 лет назад

MotoMerica actually I found later that I just had to push the wheel foward after I slack the chain. They say it in the manual, it's quite easy.

@MotoMerica 7 лет назад

okay i'm glad it worked out

@mattb6646 Год назад

Hard to get calipers up under there to measure... tape measure works fine

@richardgoodwin3087 3 года назад

@motomerica I have a 2016 fz-07 and I’m currently attempting to make sure my chain slack is good(why they made it so confusing in the manual I’ll never understand) do you think 5mm is gonna be detrimental in terms of tightness because let’s be honest who knows how much 15 lbs of pressure is

@Yippaah 6 лет назад

I have the exact same bike in colours. Thank you for this video. It helped me bunch

@thechristianbugok 7 лет назад

your channel is Very Helpful! Thanks Mate from Philippines!!!

@MotoMerica 7 лет назад

Awesome thanks for watching check out the rest of the videos

@ImNotADeeJay 3 года назад

I hate chains with a passion... I wish there were more belt or shaft driven bikes

@mikasihite5346 7 месяцев назад

You loosen with a torque wrench ??

@motofan16 8 лет назад

My manual seems to suggest that the measurement should be from the low edge of the fin of the chain guide (the rubber/plastic one) to the middle of the chain...

@MotoMerica 8 лет назад

Yep do what your manual says. Mine is from the US 2015 bike. I think someone else said the 2016 manual is different. Thanks for watching my video.

@MotoMerica 8 лет назад

Follow your manual for your model year

@jrock1520 7 лет назад

Your manual is the same as the 2016 FZ.

@bdavies1995 8 лет назад

hi mate, great video and very helpful how often do you need to tighten a chain? thanks!

@MotoMerica 8 лет назад

If it's a new bike it will mostly stretch a bit the first 500 miles. Afterwards I would check it every few months but it will probably be okay when you check. Lube it often if you ride in the rain.

@matej.mlakar 8 лет назад

A mechanic told me that the best way to know when to lube the chain is when it is shiny (silver).

@MotoMerica 8 лет назад

I just got some chain lube from Amazon. Made by Royal Purple - I will give it a try. Thanks for watching.

@LeaveYouOnRead 5 лет назад

What size is the socket for loosen the axle?

@MotoMerica 5 лет назад

Good sockets to have around for the bike are 27mm for rear axle nut, 19mm for the front axle, 17mm for the oil drain plug. Ride safe have fun!!

@LeaveYouOnRead 5 лет назад

@@MotoMerica Thanks a lot! Ride safe man!

@vladz8754 Год назад

Thank you so much for making this vid. A lifesaver

@VideoGamesandVlogs 8 лет назад

Good stuff. Man. Need to go check mine. should be good but gives me a much better Idea of what im working with on my fz

@MotoMerica 8 лет назад

+VideoGamesandVlogs ...yep mine was off quite a bit.

@ocalalightshows Год назад

Nice how to video thanks

@JacobTJ1 2 года назад

Thank you good sir

@craigr306 4 года назад

my air gun clicks lol

@garethlewis3743 7 лет назад

Thanks for the video. I had a training session in my place of work about using torque wrenches and the guy said never click more than once, also lubricating threads will over torque the fixing regardless of the wrench click.

@MotoMerica 7 лет назад

Good information thanks

@MMMHULKSMASH Год назад

is it normal for the chain to touch the top of the swing arm?

@MotoMerica Год назад

No I don't think so. Check your manual as some model years are different than others on hos the chain is tightened.

@yellowgreen5277 8 лет назад

Nice

@MotoMerica 8 лет назад

+Cbr 600 ... thanks for watching

@carlosfrancofeliciano6160 Год назад

Excellent !!

@BallBagNZ 6 лет назад

Yo don't use tour torque wrench to undo bolts or nuts. It's a precision tool and not ment for that use

@MotoMerica 5 лет назад

Okay thanks

@terpt6558 5 лет назад

did anyone look at his sprocket???? why does it look messed up to me? something is not right!

@MotoMerica 5 лет назад

TerP 81.... You may want to be more specific with your question. Bike had less than 1000 miles on it when this video was made. Nothing wrong with the sprocket.

@terpt6558 5 лет назад

@@MotoMerica mine is hitting 1100miles, just comparing it to your video, seems like your sprocket teeth are shaved off, might be just the video....

@QuickShifter 8 лет назад

Thanks for sharing this mate, Im wondering, can we do it without a tork Wrench?

@marcusmorales2435 8 лет назад

*torque

@MotoMerica 8 лет назад

Hey I would recommend borrowing a torque wrench if possible but if your fairly good with tools and mechanics you could see how tight the bolts are before you remove them by trying to tighten them a quarter turn with a normal wrench and feel how much pressure you put on the wrench to move the bolt. Then after tightening the chain use the same type pressure to tighten the bolts. However, definitely torque them to factory specs when you can or at least check them before riding to make sure it is safe. Good luck be safe. Thanks for watching

@QuickShifter 8 лет назад

MotoMerica Thank you so much, cheers.

@mikesanders902 3 года назад

I love you man!

@alexcastillo1997 6 лет назад

You need some body to measure the chain while you are on your bike because the chain tightens when you sit on the bike.

@nathanhale7001 6 лет назад

Not according to the manual.

@kyledavisroberts4144 5 лет назад

Manual says to measure kickstand down, with no weight on the bike

@Madnoodlemax 5 лет назад

Good night sprockets way to tight

@MotoMerica 5 лет назад

Thanks for your comment

@SR71BBFLYER 5 лет назад

Good video...subscribed.

@pauljones-tj5vs 6 лет назад

Great video thanks man

@mgoze 8 лет назад

great videos, but i have a quick question. I am a new rider with 0 experience with motorcycles whatsoever, ive been looking at this bike for quite awhile and was wondering how this would fare as a beginner bike? I realize its a lot of engine for beginners, but since its power curve is linear, it would possibly be manageable. Would you recommend something smaller or do you believe this is a adequate for a beginner? Thanks!

@MotoMerica 8 лет назад

+Michael Goze ... I think it's the perfect bike for a beginner. Just take it slow and easy. The throttle is long to open up all the way so it's easy to drive. The price makes it a plus also.

@mgoze 8 лет назад

+MotoMerica. Cool, thanks for the response, I really appreciate! Subbed too!

@MotoMerica 8 лет назад

awesome thanks

@AJHDuk 8 лет назад

Great video... Thanks for the upload, saves me going through the manual 😂😂

@MotoMerica 8 лет назад

+AJHD ... No problem. It's a pretty easy procedure. Thanks for watching.

@StayVerticle90 8 лет назад

Your wheels are so clean!

@MotoMerica 8 лет назад

... thanks for watching. I just use WD-40 on the wheels - spray it on wipe it off. Just don't get it on the tires. It removes the oil and wax that gets on the wheels from the chain. Simple and cheap.

@matej.mlakar 8 лет назад

This could also be content for your channel :)

@MotoMerica 8 лет назад

Good point thanks