Your video is so informative and easy to follow. My very first lift account I just bought an 1889 12,000 sq ft bldg in need of repair. My friend just retired from his construction biz and sold me his beast Genie S60. He would come over and show me things. Next trip was what’s behind the box. He passed away suddenly and now the lift does exactly the same thing: crank no start. So thank you much for explaining things the way he did: layman’s terms. Getting the close up views was a bonus as well.
This video was alot of help. I just lost power to my genie lift after a heavy rain. It ran fine then mid use 30 ft up it lost power. Someone sent 2x12 out 3rd story window to get me free.I'm gonna check my relay connectors like in this video and see if one is nasty. Thanks for the upload was a godsend .
great video!! i work on lifts,and i'm usually by myself.I use a12v beeper to hook up to circuits that i can't see (sometimes it's nearly impossible to see a test light
Dear please help me, how doing in my Genie Z-45/25 when always the light Number 9 and 2 in the Start Module 56057 first is on, after 3 or 4 second off together lights, and off the engine, thank you Sr
My genie s-85 ran out of diesel while i was working, Luckily it had enough fuel to reach a balcony and get out but now i've been told that there is going to be a problem because as It ran out of diesel there is going to be air in the fuel Pump now, can you tell me how to do to let the Air escape from the fuel Pump, i haven't tried yet and tomorrow is when i Will refill the fuel tank but i want to be prepared, than you so much in advance.
You will need to bleed the air out of the lines. On top of the fuel filter housing is a bleed screw. Operate the fuel primer lever until clear diesel with no bubbles are present. Close the bleeder and start the engine.
Hi, I've tried to update the software on Genie S-85 XC year 2018 (Bootloader 1302967-1.7.1 and Firmware 1302966-1.9.5) via USB. The Bootloader successfully installed and during updating of Firmware DISCON, PCON main, PCON secondary and TCON secondary successfully update 100% but TCON main not updating and showing message "Sub-ECU not responding try to recovery. I've checked wiring and CAN resistance on J5 and J10 connectors, all good. The Genie have ALC-600 controllers. Can you please help me. Thanks in advance.
I never have the luxury of having wiring diagrams at my disposal so I'd be that guy going around checking grounds, power, fuses and relays. 99 percent of the time I can find the issue that way.
Luxury? Genie wiring diagrams are free to download or view. I don't always have the diagram for the machine I am working on, but I darn sure use them when available. I'd be a rookie if I didn't. A lot of the time I know which fuses, relays and wires I am after before I even get to the customers machine.
So like you I really like to look into a schematic and see how things work, but say the the machine is throwing tilt sensor codes or perhaps I familiar with a certain machine did my function tests and think the tilt sensor might be having a issue. I may look at the sensor and connector to see if anything looks off/not oem. Did this last week and noticed the seal on the tilt sensor was a bit pulled out, a pin was intermittently making connection due to being low. In this video example think you did the best thing, have wasted alot of time pulling on shit due to having no wiring diagram.
Good job 👍, but sir i really want to be like you on this job sir. What will i do? How will I get online training from you sir and what will it cost me sir?. Please sir I really need your response on this sir thanks.
@@paulsequipmentrepair823 tell the truth not because iam here but it's really nice sometimes iam working these lift iam about 1/8 mile or less from the sea or beach but the sea frost messes with a lot of equipment rust wise
@@paulsequipmentrepair823 the problem iam having I go up max and down max with the jib 10 times platform say level but as soon as I raise main boom the platform tilt and platform levell sensor goes off and flashes red beside basket levell toggle switch
@@paulsequipmentrepair823 question 2 z80/60 we took the generator to a shop get it clean up and they test it good but the pump that's attached to the generator is not turning, when we remove the generator I turn the shalf on the pump with my hands
@@paulsequipmentrepair823 question 2 z80/60 we took the generator to a shop get it clean up and they test it good but the pump that's attached to the generator is not turning, when we remove the generator I turn the shalf on the pump with my hands
Using wire piercing probes can leave a place for corrosion to begin on the exposed copper. What do you do about the hole in the insulation after you're done testing each wire?
