Genius Guy 6 Projects To Restore Machines From Scrapyards // Masterpieces Of Mechanical Engineers 

I love his torque wrench technique. What an amazing job. And then the warm up run with no coolant until the engine is about to seize. Maybe he can rebuild my car?

Cmo é possível os seguidores deste canal elogiarem este trabalho de reconstrução?desmontar tudo de qualquer geito uma escovadela e pintar,não indo a pormenores isso é um trabalho de quem não tem um pingo de brilho proficiomal.

That engine “rebuild” was painful to watch. That engine is worse off now than it was before he “rebuilt” it. Reusing all the seals and bearings, not decking the head, reusing the cylinder sleeves and piston rings, not rebuilding any of the injectors or the injection pump, AND NOT TORQUING A SINGLE BOLT!!!

How do you keep up with all of the nuts, bolts, washers, cords and parts and where they go? Amazing.

The first machine will be very handy. Great job since it's scrap.

Great Job rebuilding all of the equipment.

Wow Gracias 🥰🥰🥰 🤜🤛

It all seems good but no torque wrench one mains rod bearings not good

Saludos de Puerto Rico caqueta colombia muchas bendiciones muy buen trabajo lo felicito

You did a great job reviving a great new video with good and skillful content..Keep up the good work, genius master🔧😎♥♥t

Finally the video has loaded🥳🥳🥳

Video yang cocok pada waktu malam

Keep up the good work.

Usted es un hombre que sabe lo que hace felicidades

great work bringing life back into these useful machines. very much looking forward to see other things you make useful again. take care and have a great day

Restorations Tools retuns and provides again new awesome video with great content and skillful..Keep it up always genius master🔧🔧😎😎♥️♥️

Torque fly wheel for sure

I agree with you use to get rings to seat running one hot but not to hot

Malaysian 🤝 Vietnam in video❤❤👍👍

this is how new bearings are treated, putting new ones on is reprehensible and unacceptable, it makes your eyes water :( and with a steel hammer instead of a copper or rubber one, because I'm not even talking about the filling tube

I'll bet a sandblaster is on your wish list!

where is the last few mins of video

I wish he would find out how to properly install the bearings. The way he does it causes the balls to indent the races.

The best

I can't see how that little air hose supplies enough air for that impact. On the engine rebuild.

Ура, загрузилось🎉😊

Rebuild without a torque wrench, no plastic gauge?? I bet that engine won't run for long! Speaking of long? The video was way too long!

能骗就骗 is this guy who rebuilt that engines motto

1:11:04 burn head gasket because not have water pump working and belts.

Цепи хорошо замочить в керосине апотом их легонько простучать и ипромить в томже к росине после поместиь в посуду с более густой смазкой инагреть смазка станет житкой и проникнет во во все сочлерения цепи , иоставить до полнго остивания цепь еще поработает ,метод прочерений , я в молодие годи занимался мото техникой Метод пртверен!!

Perfect 👌

Видео не загружается😢

Great Job!

Can’t buythis no torque specs spin Bering does good work but lacks schooling or specs😊

И кто ставитоткритие потшипники откритие или самому сделать защиту от води грязи

Man i think that you could have cleaned most of the rust off of the pins and the gears while you had to break it all down anyways even if it was a guy like me to watch and learn how you should do it right the first time ! still like your channel, that's just the way I would have done it I think !! keep fixin um up & I'll watch um !!

Mega!!!!😮

I hope he took the number 4 rod cap back off because there was trash on the crank journal.

To long no water it burn up

Vc é o melhor do yotub amarilo Brasil 😂😂😂

Мне нравится у Китайских братьев они любую технику или вещь возьмут со свалки и вернут ее в ро.очее состояние ,уних девочки тоже ремотируют єлектро инструменти ,а ониби лутше своей красотой укиасили подиуми извесних мобельеров демонстрируя красивую одежду ,в них подходят все данние , а незаниматся реанимацеей мет алолома

Widen fan out turn pressure down

Доработай ето трубогиб електро приводом с ребуктором винт прижима веихний

No ring sizing no cleaning g cylenders not over all good

Water dude

Unfertiger *Mist*

Это не рестоврация

👍👍👍🙏🙏🙏👏👏👏🧡🧡🧡

This guy would give Rick from American Restoration a run for his money.

🔧🔧🔨🔨👨👨😎😎😎👍👍👍👍

The video is too long my friend, it is not loading

P 0 P P Pp P P P 0 0 P 0p

THE. BEST

Great Job rebuilding all of the equipment.