GETTING READY TO FIRE UP THE 1935 HUPMOBILE / FORD HOT ROD

Подписаться 319 тыс.

Просмотров 87 тыс.

50% 1

Today we're getting ready to fire up the 1935 Hupmobile / Ford hot rod. First we're going to test the radiator for leaks, install the gas pedal, connect the throttle, wire up the gauges and the list goes on and on.... 🔥
IF YOU ENJOYED WATCHING:
subscribe, leave a comment and hit the like button
/ badchad
CHECK OUT OUR MERCHANDISE HERE:
www.hiltzautoco.com
FOLLOW US ON SOCIAL MEDIA:
/ badchadcustoms
/ badchadcustoms
/ macintyrejn
/ ___jolene
MAILING ADDRESS:
Hiltz Auto Co.
RR3
Canning, NS
B0P 1H0
#badchad #engines #flathead #hotrod #radiator #plumbingaradiator #tutorial #rustrepair #wheelwell #metalfabrication #chassis #wishbones #firewall #fabrication #firewallfabrication #1935ford #1935hupmobile #modifying #brakepedal #gaspedal #clutchpedal #fabricating #driveshaft #rearend #junkyard #gasser #chassis #flathead #1935hupmobile #mechanics #flatheadengine #hupmobile #classiccars #vintageracecars #1935ford #sixcylinder #1936ford #engines #hotrods #rustrepair #autobodyrepair #patchpanel #car #carrestoration #carrestorationrustrepair #driveshafttunnel #racecar #1935ford #flathead #metalfabrication #1935ford #automobilerepairshops #cars #classiccars #hotrods #racecars #choppedford #badchadcustoms #supercar #trog #theraceofgentleman #dragracing

Авто/Мото

Опубликовано:

21 окт 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 534

@fredroberts8810 2 года назад

The copper pipe wasn't soldered properly and it leaked. Taking the cylinder head off in the future is going to be really hard due to the welds from the throttle cable. That's what you get from "free range auto construction", and its more entertaining than any other car show anywhere! Love the bumps and hiccups as much as the successes.

@f150bc 2 года назад

Every house we built we tested the copper heat lines for leaks when we started the heat and ran in water to the boiler,as far as the head get a wheel and cut the welds ,this is a shop car running the 1/8 mile no big deal.

@leodurant7533 2 года назад

One big hiccup!

@tomwinkle5536 2 года назад

It will be a rubber hose before it goes too far..

@raeanker3078 2 года назад

@@tobygathergood4990 Where do we find your RU-vid channel showing us how you would do it.

@TheDiamondback73 2 года назад

Why do I always find myself hollering at the tv, trying to get Chad to do something the way I think it should be done???

@josephpilosky4775 2 года назад

Chad is good at building cars , but the simple stuff it hurts me lol but he will get it

@josephpilosky4775 2 года назад

@@tobygathergood4990 yes I do too lol, but some things he good at

@josephpilosky4775 2 года назад

@@kukuipupule4415 lol

@ele97735 2 года назад

I’m with you on that

@moudyblue 2 года назад

Spontaneous engineering

@fingernailfreddy7335 2 года назад

Hi Chad, loved the interview the other night. I had to laugh because I have said to my wife You're like the Bob Ross of car builds and then you said it lol. Your soldering needs some work. It is called sweating and requires much less solder than you're using. Put a damp rag where you want to control the heat, so you don't un sweat a joint and put all your heat to the fitting and the heat will draw the solder in. Just a heads up for the next time. When done right you will see very little solder in the joint.

@Frontireadventures 2 года назад

Nice positive way to help. Good on you.

@gehrbox 2 года назад

Chad you know you could have just pulled the cable out of the barrel, positioned the barrel in the throttle lever, then slide the cable back through the barrel.

@colinmyers8841 2 года назад

the man dont do mechanical.

@gehrbox 2 года назад

@@tobygathergood4990 I see some genius in his creative side. He has a good eye and a fearlessness to do anything he wants. Gotta respect that. After seeing all the comments about the holy firewall I checked some of the Race of Gentlemen videos and came across an entry with no floor and no firewall. Never mind the guy running around on frame rails and a motor. Chad is an artist.

@teddyabearo1066 2 года назад

Yea...O.K. But if YOU were married to Queen Jolene...Would YOU hardleg-ego something together for her? Then get cheeky when REAL fans tried to give him (and the young'uns watching who don't know better) a heads up? Obviously discounting the twits just mouthing off. There are Mods for that kind of infantilism. 🤟🏽🐻

@gehrbox 2 года назад

@@teddyabearo1066 ya know some of his stuff is intended to draw comments in RU-vid. Builds the channel.

@ele97735 2 года назад

I was thinking exactly the same thing. He could have used a drill bit the exact size of the barrel so the barrel would fit in there perfectly.

@tracyschmitz9192 2 года назад

People sure can be critical. Bad Chad is really, really good at working with what he has. It's a pain in the butt to run out for bits and pieces when you live in a rural setting and it's not likely the one or two parts stores are going to have what he needs. All of the critics probably haven't built anywhere close to the amount of duke ass cars that Chad has. It's easy to sit in a comfy chair and tear someone down.

@thomasjones3005 2 года назад

There was a time I had a 29 Rodster body on a later Ford frame runnin a old Chrysler hemi thru a old Ford floor shift to a Columbia 2 speed rear end. zoomie exhausts, no lights or plates of any kind. It was great for the occasonal very late night quick run around town. Usually took about a case of beer for self and friends to get it moving. It was a blast for 10 or 15 minutes. I think of this old Hup along the same lines. Fun as hell for a short blast, with a little priming to get it going. Hang on tight Jolene, it's going to be rough exciting ride..

@bigjarn 2 года назад

drill a hole through the screw and you will have duplicated the way many small engines are controlled

@reneekrueger962 2 года назад

Um, I’m 30 seconds in and wondering if maybe there was some other way to enlarge a hole? They have these new things called drill bits that may possibly work.

@faerieSAALE 2 года назад

or the nuclear option - the plasma cutter!!!!!

@alethacriss1528 2 года назад

Yup, pardon me while I go hug one of my drills. He is a great designer though.

@williamchildress1459 2 года назад

It is called a drill and drill bit.

@123suzukisamurai 2 года назад

Love watching yr show. Don’t know why people gripe so much about how the build is going. Enjoy it for wat it is guys. It’s a period build. How it would have been done back then. Don’t compare to how it would b built today. The creativity is great. If u watch u can pick up a few ideas u mite like and use yrself. Or wat not to do. If it bothers u too much watch something else. Above all we all know u armchair builders no more than a actual builder but u really don’t have to keep telling us. Just enjoy the show guys

@kennethstevenson976 2 года назад

Make a rod just smaller than the hole in the peddle mech., drill a hole the size of the cable in the rod, insert the rod across two holes, insert cable through the rod, insert cable into cable sheath, done. On the carb end, drill a hole near the bolt head, fasten the cable by tightening the cable to the head of the bolt with the first nut, then fasten the bolt to the carb with a self locking nut so the shaft moves freely.

@i8ntnuts 2 года назад

I kind a wish he would do something different than playing with the throttle. The last thing he needs to work is the gas pedal. I think he has plenty of cars out in his yard he could take a bracket off of, or at least get some ideas. Plus I admit I would rather watch him cut cars up. I think he has me spoiled with his custom work on the old bodies. I guess a last ditch effort he could phone a friend. It would be fun if Jim was there. I bet Jim would love to help him. The show just isn’t long enough.

@howquick 2 года назад

I had a look at some of the RU-vid Pine Tree Jamboree footage. Awesome looking cars….yours is gonna fit right in….’and’ stand out. A few of the “that’s not safe..Can’t believe you’re going to let Jolene drive it” crowd ought to take a look. Some of the cars are basically a seat on a chassis 🤣.

@howquick 2 года назад

@@65cj55 your comment is ridiculous. Have a look at the type of racing they’re doing and the cars they’re doing it in. You lot aren’t about “it’s not safe for Jolene”. You’re all just using that as an excuse for a whinge.

@larryrice3611 2 года назад

Simply amazing fabrication! I've known old guys who lived through the depressions that taught me working with what you have not groaning about what you don't have just like your doing! Keep up the good work!

@briandepoppe7209 2 года назад

I had an antique tractor with a drip and wired a soup can under the drip. It would catch the water and you could put it back in the radiator. And it looked so cool and got a lot of laughs. You all be happy 😊. Brian and Debi

@philipburrows 2 года назад

Hi chad Do you have a return spring on the gas pedal or as us British would say accelerator pedal? Where the leak is on the copper pipe might be a cold spot from when you soldered it, it just might need to be reflowed the solder with a touch more fresh solder just to be on the safe side. You could make a couple of caps so you can cap one end of the pipe fill the pipe with water and cap the other end and check for leaks then when all is good and leak free remove the caps empty the water and fit the pipe to the car. The car is looking good Chad, cool to see car's being transformed into a beautiful work of art.

@KevinCoop1 2 года назад

I am looking forward. To seeing Jolene driving across a field soon.

@eltonnoway5692 2 года назад

Yikes ...watching Chad continue to try and ream out the hole with a tapered die grinder bit for the cable fitting was making me crazy. I kept screaming at him... "Use a drill bit for Christ sake and just drill the correct size hole!" {sigh} That kluge of a fitting has to be one of the worst jury rigged things I've seem him do yet.

@alethacriss1528 2 года назад

It looks like the radiator is turning out well, this mechanic work is yet another experience that not all creative body work designers have to deal with!

@chrisboehme4695 2 года назад

With all the work both of you are putting into the gasser, it would be nice to grind down the body wields and paint the car. Even if you make it look relict? Thanks keep up the good work, You are truly an inspiration. Thanks

@johnjackett3138 2 года назад

Can't wait to see this machine run under it's own power with Jolene behind the wheel....good luck Guys

@tonyriley5233 2 года назад

Hi, I've really enjoyed your videos, and may have a suggestion for the audio problems that keep happening. The transmitter on Chads belt just needs to be received by another receiver that Jolene can monitor while she is filming with an earphone. Just find the frequency that is being used and add another receiver that uses the same frequency. If Chads movement unplugs the microphone, Jolene will not be able to hear him and can fix it. She will know instantly.

@Bikeops2021 2 года назад

Yeah sure thing! 😂😂

@jamesclark1131 2 года назад

I do think that some people miss the point. Chad is not a master mechanic. He is clearly self taught and he is showing what the normal guy with basic tools can do if he has the will and the way to build a hotrod in his garage. It's not about copying what he does it's about finding the drive to find your own way including the mistakes along the way.

@markmarotti3623 2 года назад

what a fun project. Every part is using creativity to design on the fly and make it work with stuff already in the garage . Reminds me of the old days when i drove beater cars and did what ever it took to keep them going on the cheap .

@andrelozier5008 2 года назад

Hi Brad and Jolene, your doing a great job. You could wrap the gas cable around the nut and tighten it. It would make it more secure. Can't wait to see it start up and move around. Take care.

@Gscalenut 2 года назад

The amount of time and effort taken so far could have been better spent finishing off Jolene's Bugatti. I will be glad when Chad has scratched his itch and finally gets back to doing the things that actually built the channel.

@beekeeper213 2 года назад

Come on tonsay the bugotti zor any build built this channle is dumb... Him building built this channle...long before his tv show way back to his first magizine article... Get a grip... Man does it his way and thats his way..dont like it go find someone else to watch.... Hes not a mechanical person... He builds cars...

@Gscalenut 2 года назад

When Chad resurrected the original Bugatti build the subscriber count was in the early 50,000's. He had let Jolene's Bugatti build stagnate for around two years until that point. It was Jolene's resurrected build that got the channel moving. Jolene's Bugatti plus the second Bugatti build quickly accelerated the subscriber count to almost 100,000.

@garydonaghue619 2 года назад

Everyone is excited! Can’t wait to see that rod, Rock n roll! Thanks for all the ideas!!!!!

@johnnydanger57 2 года назад

They are at it again, Chad! I don't see any of the commenters building cars here, but they sure can tell you, you don't know what you are doing! I know it doesn't bug you, you know what you are doing. Keep on keepin on!

@gregorystroud6119 2 года назад

That little clip you are using for the throttle cable is made like that for a purpose. Drill a hole at the end of the plate, slot it and slide the clip onto the plate. Drill another hole to mount onto the carb manifold. Easy peasy when u use a drill. OK to Weld onto frame, but not motor, brakes etc.

@kevinmcleod3741 2 года назад

Needed a grill to fire 🔥🔥 it up lol . Steaks and chops 😋 mmmm good 👍 . Lol ! Thumbs-up on getting it up and running! Cheers and thanks! Thumbs-up Chad and Jolene 👍 great job! Aand a Thumbs-up for Doug 👍.

@mikelynch8683 2 года назад

A small room off the shop would be a good place to put your compressor so it's quite in the shop

@Maintenance101. 2 года назад

Love watching these guys, lots of knowledge

@donthompson9300 2 года назад

Just watching from home, but I think making the throttle cable bracket would have been easier to weld the bracket to the top of the metal above the perferrated firewall. All in all, a great "It's Friday video.

@scottbenjamin5047 2 года назад

Your soldering just needed more heat. The tip of the blue flame is the hottest part, but to fill that gap with melted solder perhaps MAPP gas as one guy suggested might work better. And wrap a wet rag around the other end of the fitting of course, so it won't unsolder.

@noponder 2 года назад

Amazing work. I look forward to seeing Jolene drive it for the first time.

@bradleymckay365 2 года назад

Chad I have been laughing my ass off every damn time you find out how freaking awesome that firewall is for mounting accessories... I don't think people understand how funny you are. Thanks for teaching us a dying art...

@davebuckholts 2 года назад

Ready to hear the old flathead fire off! First engine my Dad and I rebuilt together was the flathead V-8 in a 1950 F1 truck.

@jeffyates4813 2 года назад

Chad what you could do to make the throttle cable work better is to take two washers the next size larger and weld a spot at the top of the two and a gap on the other side spread it wide enough where the cable will go against the welded side and put it on the bolt. The weld will retain it and the gap will pinch it when tightened.

@kevinmaher813 2 года назад

The piece you wee trying to fit through the accelerator pedal slides off the cable. Drill a hole to fit that and slide it into the holes without prying the end apart. Then slide the cable into place and through the firewall. Watching you do that job had me shouting at the TV. Less haste, more speed; take a minute longer and think out the options. Perhaps ask Jolene if she can plan a job like that before you attack it.

@peterjuhlke7437 2 года назад

Can't wait ,looking great guys , another piece of road art ! awesome guys,thx for sharing this with us.

@barriecollins6838 2 года назад

The rubber seal has probably hardened after being stood for so long in the water pump that is Chad and jolene. It may seal its self up once it gets hot again and makes the seal soft .some of the water pumps have a small hole in the metal underneath the pump

@438DICKY 2 года назад

Good to see you are still on the car? Which one you might ask.....Great stuff Chad thanks!

@phillipcaldwell434 2 года назад

G' Day Downtown John, nice to see you back again helping BAD Chad out with his Mechanical issues Keep on moving on you'll get there soon

@darrylway4910 2 года назад

Not knocking anything but is the throttle cable connection going to stand up to hard acceleration. Have you thought about drilling a whole through the bolt then thredding the cable through,then looping the cable and clamping it ,then tightning the bolt so the cable can't be pulled through. Love your work guy's,enjoy it every night😍👍

@ronc6249 2 года назад

Hello Chad and Jolene sounds like the moment we've all been waiting for! Waiting to hear the beast run! Getting closer every day to being completed, keep up the great work both of you.

@RolandFieldsTV 2 года назад

It is time to fire it up

@i8ntnuts 2 года назад

That will be fun. Can’t wait to watch.

@ate-updesigns9186 2 года назад

Closer and closer...cool setup...that firewall is working out pretty cool for bolts 🔩 and attaching stuff..jolene is gonna be driving soon..thanks for the cool episode chad and jolene and downtown John 😎

@rredbeak 2 года назад

Chad,its an old car,in my old car days we put gasket glue [liquid type] inside radiator hoses etc etc,then screwed them on as normal. as engine heats up glue seals n dries still flexible but fully sealed.. removal is easy cause its not a locktite deal.just gasket glue

@alexandriawootton1742 2 года назад

Getting closer running and driving, there will always be issues regardless, that’s when we continue to learn and progress, old cars are just that old cars, doing great Chad 👌

@royjohnjennings1717 2 года назад

In all honesty would you buy a car from this man

@alexandriawootton1742 2 года назад

@@royjohnjennings1717 honestly I’ve seen a lot worse. Chad may use unconventional methods at times but believe me some of the vehicles we’ve had to go through and the things other people have done would make most people cringe 😬. When you see Chad using liquid nail and not welding frame then you can show disbelief in his work LoL, my opinion 😉

@mikesimmons6063 2 года назад

I know we have coat hangers already involved. I'm still waiting for some bailing wire to be used somewhere! "Get-er Done" Not a show car is an understatement.

@stopcensoringmyfreespeech3280 2 года назад

If you put the burr deeper into the grinder it will run 10x smoother instead of all the chattering and bucking. At the foundry we use to cut the burr shaft off some so it could go into the die grinder all the way if we felt like doing so.

@quinnwarman5139 2 года назад

I think you may have been a bit quick at chopping the throttle cable adjuster that goes thru the firewall as you cud have just moved the nuts further along and it would have worked and then u would still have full ajustment there incase needed later Goodluck keep it up

@chrismartinez8658 2 года назад

Kick ass you guys. Cant wait to see Jolene behind the wheel

@Rleydic1 2 года назад

Brad that bolt you used for the throttle cable drill a hole through it and put the cable through it then put the bolt in the hole on the carb and tight it down the bolt will try to pull the cable through the hole where the bolt is and it will hold it

@i8ntnuts 2 года назад

You guys are the best. I hope the mechanic can get your car running for you Jolene. Some love for Fina also.

@williamoneal2763 2 года назад

Put two small teaspoons of black pepper in radiator. Should seal leak. This is what was used in 20’s. and 30’s to stop leak in radiators. Cheap fix and it works.

@mattcasoni 2 года назад

Can’t wait to see this project on the road. Awesome work!

@dwalker399 2 года назад

It's not a road car. It's being built as a drag strip car.

@mattcasoni 2 года назад

@@dwalker399 it’s a double project. The truck that’s pulling it will be on the road. The car of course won’t be actually driving on the road.

@mconfluence 2 года назад

Chad drill a hole in the bolt up close to the head of the bolt big enough for the cable to go through then put the washer on and tighten up the nut. It will pinch the cable tight.

@rcbodyshopfr 2 года назад

All these little things that need to be done at the end are stressing when you really want to start the engine and drive! Well done in Chad's way!😁

@antoniocovarrubias7831 2 года назад

I can’t wait to see that hot rod with roaring engine running, that reminds me that once I was fifteen too! Greetings from California.

@pablorivera6879 2 года назад

Love the progress, pretty anxious to see Jolene ripping down the track.

@jarnosaarinen4583 2 года назад

Really taking shape now, looking forward to seeing it going down the track!

@bradleymckay365 2 года назад

I get more and more excited for you guys. I absolutely love that you are in control of your life ♥

@charlielemmons5525 2 года назад

A drill bit may have been a better choice to enlarge the hole. Let's hope it's only one small pin hole to fix. Jolene does a fabulous job with the camera.

@martinmclain9861 2 года назад

FYI and I'm sure you know but haven't noticed. The radiator fan will pull air from the easiest place it can get it. You have a very big hole at the bottom of your fan shroud and should put a piece of metal at the bottom to seal off the air flow from coming around your radiator instead of threw it.

@fredhoman6101 2 года назад

building on the fly ,love to watch every single day coming this build going together ,thanks for sharing

@deanglagoloff9735 2 года назад

can't wait to see the wheels kick up some dirt. great job and channel.

@aabartu3 2 года назад

A whole lot coming together at once! Great job!

@brianlawrence8867 2 года назад

Great expectations😊

@56CrownVick 2 года назад

I can't wait to hear this car run, and to see Jolene driving it.

@davidtutor6763 2 года назад

Loving it. Thanks for the hard work you two

@jimmyattard1446 2 года назад

Boy....I find myself trying to verbally direct Chad as he works, as if I know better.... Yet I'm learning more than I ever thought I would!

@carlmalone4011 2 года назад

Get yourself a cooling system pressure tester to find leaks. Well worth the money

@alancroft4231 2 года назад

Can't wait, let the adventure begin. It's been a lot of work that's for sure!!! Hope all goes well,, no leaks

@i8ntnuts 2 года назад

I can’t believe the water pump leaks after only 87 years. They just don’t make them like they use to boys. I bet the warranty just expired also! Isn’t that always the way

@maryh7924 2 года назад

Hey Chad, Jolene, and Fina! Nice to see the race car coming along 👌

@robertdehaes9329 2 года назад

just checking in on the progress, keep up the good work everyone!

@kevinkelly1523 2 года назад

Another fantastic episode. Thanks once again.

@williamsons79 2 года назад

Very encouraging video, appreciate your time and efforts along with the Pepsi art( step dad was marketing director back home everything was Pepsi).

@coltonupchurch4368 2 года назад

Looks good 👍🏽

@jparish2469 2 года назад

like bob ross no mistakes just happy little accidents .love the curves you take to find a way to do what needs to be done great work chad .great filming as always jolene thank you

@geoffhastings281 2 года назад

Sorry Chad, I love your bodywork skills and the finished results are brilliant but , your throttle cable fitting skills need some development. That two minute job turned into a marathon. A set of drills would have given you a round hole the cable would fitted in seconds, You could have then removed the round pivot from the cable nipple, slipped it into the throttle pedal without having to spread the pedal lever. Then pushed the cable through that and through the bulkhead. It got worse, surely removing the head nuts and clamping a bracket of some sorts under them would have been better than welding that piece to the nuts?

@christinebornstein8239 2 года назад

Hot Rod looking great! Keep up the great work. Excited to hear it run today! Enjoy your show.

@i8ntnuts 2 года назад

YES !!! I was so happy when Chad said he would stick with it and get it running today and show us the video. Two videos in one day, how cool is that! Hit that old like and subscribe button boys.

@wilburcowart9590 2 года назад

Put one tea spoon of back pepper, and it well stop the leak without stopping up everything else.

@ronlynch7744 2 года назад

Good call Jolene on moving the battery to the passenger side, closer to the starter for less cable to wire up. 😎👍🇨🇦

@johnhoover9555 2 года назад

Good luck on the fire up Chad.

@keithnelson1123 2 года назад

I think you showed a lot of the arm chair quarterbacks a few things on that pluming work. Great job as usual 👍

@henri-paulhinse426 2 года назад

congratulations. Thanks Chad and Jolene.

@HotLinQ 2 года назад

Greetings from Vegas

@davidgrubb4442 2 года назад

The suspense in unbelievable

@jimcoplan9502 2 года назад

Detail work to get the race car ready for its first startup. Moving the project closer to completion is a good thing.

@roymazac2532 2 года назад

Let the games begin. One step at a time. Thanks for the video

@patmcnally6 2 года назад

Going to be Great when she Starts up and Moves around the Doe yard

@larrybailey43 2 года назад

Looking good !

@shotgun283 2 года назад

Reminds me of the good ol days, getting mates together working on cars

@billmiller7138 2 года назад

Yep reminds me of when I was 12 or 13.....

@claudeperron8197 10 месяцев назад

It's Friday ! Actually it's Sun 2023-10-08 for me ;Watching unseen past videos ; very interesting and love watching you all having fun also ! On to the next, My ache ache, eyes lol

@weirdmatter 2 года назад

Fun times!

@genesimons8368 2 года назад

Folks need to take into consideration that this is pretty much a "one event vehicle". Then put away until next year's race... Here's hoping Mz Jolene takes home the 🏆.