Harbor Freight 1 TON Foldable Crane Unboxing, Setup, and Review 

Very nice video. Good job reviewing it. Can't wait to see more videos soon my friend. Keep up the great craftsmanship and hard work my friend. Forge On. Fab On. Weld On. Keep forge lit. Keep making. God bless.

carefully check wheels before assembly. I had (4) 3" wheels and (2) 3 1/2" wheels. The reverse is what is needed.

thanks for the measurements, gonna try to fit this in my 2014 mustang minus the passenger seat 😎

Haha I kept thinking that shirt looks familiar until I got a good glimpse. Got same shirt lol.

How wide do the legs open at the opening end? I can't seem to find any specs on that - I'm trying to find a solution for lowering equipment on a mobile base but not sure if the mobile base will fit between the legs enough for the machine to be lowered onto it.

Great vid thanks man helped a lot...... Any thoughts now that you had it a while ???

can u please tell me how long the legs are from caster to caster? i only have 4 ft of flat surface, want to make sure this will fit before i purchase. thx

Which crane would be best or adequate for lifting a Ford F150 bed off the truck? Would the 1 ton crane do the job safely or would I need the 2 ton crane?

How thick is the steel? I'm trying to figure out if I'll be better off building my own (heavier), or hack into one of these and modify it to connect to the hitch receiver of my truck.

Picked this up yesterday, the hand truck tire exploded when I loaded it on. (Too much air in the tire) got some solid tires on it now. Had to drag in the basement.

Can you use this on a pickup truck? My husband said it wouldn't work, not enough clearance.

what are those two collars sliding on the legs for?

I watched to see how high this lifts, but it doesn't look like it would lift an engine high enough to get it over the radiator support?

Do you know what the slides on the fold out legs are used for? Is there any reason why you installed the support braces on the outside of the base frame instead of placing them on the inside as per instruction booklet? We just purchased on of these and we are curious about the location of the braces. Thank you for a detailed review!

ارجو الفديو القادم صب النحاس الاحمر في الماء على قطعة من الخشب وتراقب الوزن

The bottom of the two red side arms go on the inside not the outside of the black base in the new models

Do you think it will lift my 7.5L 460?

mine didnt come woth the flatheads for the casters

Just in case anyone in the future is struggling with assembly and parts not lining up, keep all the bolts real loose until it is all together. Then tighten them. It needs to be a bit wobbly to get the holes to line up

Support brackets did not fit in the holes they were supposed to go in. They were too short so we just skipped that step. Wasted so much time on something so little.

😎😎😀😀😅🥰🥰🥰🥰🥲🥲LMAO! (10:42) Just imagine that hoist: ontop of a Lifted Subaru - and the backside, ((I would have to install 4 inch wheels, for the drag ramps - to the top of Custom Bed railing rack - thick wire messing. 😎😎🫠🥹🙃🙃🤡🤡😏😏 Then the cops will be pulling me over for carrying {{heavy arms}} - 🤡🤡🤡🥲🥲🥲 Serious: they be that stupid here/!\ 😎😎🥰🥰🥰🥰🤌🤌💁‍♂Awesome Demo: (9:29) I think I can get 2 legs and hydraulic centered sideways in Rack. - Worse case scenario - on the side of the road or parking lot. = 🤔🤔🤔🤔💁‍♂ Guess, I will have to use ((All Thread Steel to replace top bolt? - as a steer handle)) + Eye loop on Top of Staff - for front wench to grab a tow loop. == 3 wheel loadable: with some drilling of course.+ reversing the legs with wheels - might have to cut back steal