No video :(

Harley Davidson Wheel Bearing Installation

Подписаться 514

Просмотров 112 тыс.

50% 1

How to assemble a Harley Davidson Enforcer Chrome wheel and install new wheel bearings in any wheel using sealed, non tapered wheel bearings using the correct tools and techniques. Pay for the cost of the tool in just a couple of uses and know the job is done right.
New Wheel assembly and wheel bearing installation brought to you by Go Two Cycle.
/ go-two-cycle-893389547...

Опубликовано:

21 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@hugueninhank4168 Год назад

YOu said the front and rear sleeve spacers where different yes never mentioned how or which one was front or back....which was my whole reason for looking for this vid

@DIESELFUMESS 3 года назад

Thank you taking your time to clearly showing the process...

@isaactekancic8544 2 года назад

For the bearing spacer, there is about and 1/8th inch difference. What one goes to the front and rear

@elieli8368 3 года назад

Excellent video... Informative and and short.. No music or unessary chat 😎

@nmchugh1 6 лет назад

Great video thanks!

@dc23211 5 лет назад

Shouldnt you check bearing run out with dial caliper, i thought You have to make sure bearings are up to spacer but not to tight has to have a little play or runout??

@Madcap500 6 лет назад

Good DIY info. Aint the ol interwebb great

@ccollins9981 4 года назад

Just because the bearing has no gap between it and the internal spacer, doesn't mean they are centered with equal distance between them and the wheel hub edge on boths sides......and if not, when you mount the wheel, fabbing and installing external spacers while trying to keep the rotors centered in the calipers will be quite hellish.

@stephenWHITMER-ft8kf Год назад

Every time o see someone with a torq wrench it amazes me that they go over the bolts twice. When you do that you just torqued more. Torque the bolts once a done. Pay attention to what you did.

@donniebell862 3 года назад

Where can I get the tools for removal an install of the bearings???

@prostreetgsxr 3 года назад

Great video!

@paulosergioaraujo9409 2 года назад

hi ,please tell me if the ABS bearing is fited at the same side of ABS sensor ....and also tem me when you are seated in the bike the DOT ref should be on your left or right side....txs

@michiganborn8303 2 года назад

Thanks for uploading but 1 question, On the inner wheel bearing spacers. Did you install the rear one? I didn't see you install that on the wheel while you were installing the outer bearings I was watching that inner bearing still on the bench.

@AllanG1957 3 года назад

I would turn the adapter the other way when instaling number 2 bearing, then you wont get to much presure on outer ring of the bearing when it hit the center tube,,,just an advise

@blackonepac 3 года назад

Thx alot very informative !!!

@diegocosta9052 6 лет назад

Thanks for the vídeo! Salutes from Argentina

@kombijr 3 года назад

Gay

@larrywilkie1750 8 лет назад

When tightening second bearing against spacer, does the spacer still spin on the inside or will the bearing turn with it.

@RhunDraco 6 лет назад

I would like to know this, as well. So far I haven't seen a single video that mentions it, and it's not clear from the service manuals, either (or I just missed it).

@DarrelllCampbelll 5 лет назад

@@RhunDraco I couldn't spin mine. I was wondering if I got ut too tight. I couldn't spin tge bearing with my finger either. After putting the wheel back on it seemed okay. I guess we'll see if it kills me.

@RhunDraco 5 лет назад

@@DarrelllCampbelll I just bought a used stock wheel for my SG to replace the aftermarket one (changing the look, came with chrome wheels, I'm going with a darker scheme) and it came with the bearings and spacer still installed. The bearings spin, but the spacer does not. I am going to replace the bearings before I swap and I'll try see what I come up with on the install. I'll even check measurements on all the parts with a digital caliper just to see what they come out to, I'm curious about the specs and tolerances.