Hi , Plz give me solution for my quadcopter. After the arm all motor are spin at once but it doesn't moving up or forward Plz give me solution for this one
i am having problem with my hexacopter. when i gave full throttle it is not moving for required altitude but is pitching highly. please tell me PI gain tuning for hexacopter
+pavan karlakunta I'm not entirely sure if it's right, but try this For pitch and roll- P Gain-80 P Limit- 100 I Gain- 60 I Limit-20 You can leave the rudders numbers stock
my drone is running automatically after arming, and one more problem is that in my kk2.1.5 flight controller in receiver test setting all values are not set to zero by the transmitter trims tell me what i do for fixing these problems
hello.. i have a problem with my MINI KK (2.1.5FW).. after arming it short beeps 10 times than auto-disarms.. but if i push the throttle the motors start spinning normally.. is there any issue?
my kk board goes to armed but after 5 sec it goes back to safe like when i connect 3 motors it is working fine but when i connect 4 motors it goes from armed to safe in 5 sec and only 3 motors spin (all 4 motors are working fine individually) i did everything i could tried calibrating motors one by one and all help me please.
ey admin I'm having a trouble in starting my quadcopter. when I rise the throttle the motors doesn't spin till I push it to the middle then one after an other motor stars to spin can u plz tell me what's the problem with it
Hi, Thanks for the Vid, I really like this kk2.1 easy programing But I have 1 Q? The JST battery plug in on the board. Does and should that plug into my main battery? because I cant get my voltage alarm to go off and I notice on the board its not reading any Voltage?
Hi Kazz- Mann yes u are supposed to plugged the main battery direct to the board and then go in to Misc settings and change the alarm voltage to 105 (it you are using a 3s lipo)
Now the board is not working( kk 2.1.5 ) it display works when i turn on the battery, after 10 sec. Of plug on the battery the display got white and no switch works.
Hello sir, i built a quadcopter by kk2.1.5 but never flying it because i have facing a problem i.e when i connect battery to the quad and after esc calibration the motors are automatically runs without throttle and also witout arming.....so this is a big strange, what can i do plz help me
Hii, i left the kk f.c and no longer using that because i didn't find any solution for that issue but most probably i guess that was because of the blheli firmware esc's which is not supported by kk. So if you using that kind of esc's then replace those to simonk firmware, may be this will work but i suggest better to go for other advanced flight controllers like F4, naza, pixhawk etc. those are really awesome open source boards.
+Madhav Choksi Got it! When you go to arm it make sure the throttle trim is zeroed out on transmitter as well as the stick all the way down. then move stick to the right
I have a remote MODEL- FS-CT6B, its 4 channels are working which are aleiron, elivator, throttle and rudder, but its auxilary( 5th channel ) and 6th channel are not working, i have connected only four channels to the kk 2.1.5 board and do as you do at the video, but its not working.
bom video, mas no entanto uma das maiores duvidas de muitos é a fiaçao, cabos e receiver , por isso, se um dia quiseres faz um tbm mais completo sobre a ligaçao ate a calibraçao, mas ainda assim esta muito bem e mereces os parabens por teres esse gosto de partilhar
Help! I cannot get mine to arm? Just started doing this, can't understand why? I have checked and rechecked everything. The receiver is getting signals as the KK2 is reading them in the receiver test menu so I am stumped?