Home made bldc controller 3wire,(Type-6).

Подписаться 4,3 тыс.

Просмотров 9 тыс.

50% 1

Here I am going to make another type of home made bldc controller
Here the controller is 3 wire system and hence i have used 6 mosfet 3 phase full bridge
Top side used Irf 9540 mosfet and bottom side Irf 44n mosfet are used
Here i have used two pots one for tue the circuit and another one vary the speed of motor.
And also test the controller with two types of motors.
#bldc #motor #magnet

Наука

Опубликовано:

24 мар 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 40

@endlessriver8789 11 дней назад

Im not electronics guy but your video is very clear introduction,. Good work Sir, God bless.

@pugalstech 6 дней назад

Thanks for watching and supporting

@NishankaWick 8 дней назад

Super

@pugalstech 6 дней назад

Thanks for watching and supporting

@Edmorbus Год назад

Nice work Thanks for sharing

@pugalstech Год назад

Thanks for watching

@topinfomentary6143 Год назад

Very nice sir outstanding work thanks alot

@pugalstech Год назад

Thanks for watch and supported

@prk6034 Год назад

Good Work Sir 👏

@pugalstech Год назад

Thanks

@vlogwithvikky3846 Год назад

Great sir💯👍

@pugalstech Год назад

Thanks for watching and supported

@nayanjagirdar8408 10 месяцев назад

Very nice sir 👌👍

@pugalstech 10 месяцев назад

Thanks and welcome

@gowthampugal2471 Год назад

Super 👍

@pugalstech Год назад

Thanks sir

@meghanaharish4035 Год назад

Nice sir

@pugalstech Год назад

Thanks for watching and supported

@adibyte 3 месяца назад

Sir, please see the finished scheme.

@karnashanmugam9789 Год назад

How many watts bldc motor can this circuit drive, im planning to convert motorcycle stator and rotor to 3phase and to make self starter system will this circuit work for it

@topinfomentary6143 9 месяцев назад

Plz reply will this work on my ebike project and how much volts on which this controller can work

@patil9919 Год назад

👌❤️👍👏👏👏ईसी प्रकार का dual N channel mosfet का सर्किट बनाए, जी 🙏p channel mosfet ज्यादा कारगर नहीं होते,जब वोल्टेज ज्यादा हो,p ज्यादा गर्म होते है,

@pugalstech Год назад

Thanks for watch and supporting

@thetrue1636 Год назад

hello, the mosfet not getting hot ?

@s-tazipart1750 Год назад

Great work, i have a hoverboard blcd motor 3-phase star connection, i want to built a driver, pls i have a 36v dc battery?

@pugalstech Год назад

Thanks for watching sir

@ravinskumarexperiments1942 Год назад

आपका वीडियो अच्छा है पर P chennal mosfet नही मिल रहे है

@pugalstech Год назад

Thanks for watching Irf 9540 mosfet is available in amazon and flipkart

@meghanaharish4035 Год назад

Sir, pl send me how make a single phase home made controller

@sanhnghiemxuan7271 Год назад

How many volts is the maximum input voltage of the circuit, can you withstand 50v?

@pugalstech Год назад

Max input supply 24v dc And i have only 24v dc source unit

@sanhnghiemxuan7271 Год назад

@@pugalstech default of motor controller rotates clockwise or counterclockwise, do we have to start it manually? or auto run

@pugalstech Год назад

It run only one direction because of the sequence of conduction of mosfet. We connected ist mosfet drain to 2nd mosfet gate thro resistor and 2nd mosfet drain to 3rd msfet gate and viceversa When we change any motor lead the motor driction was reversed. If you are properly tuend the drive circuit the motor start automatically and not need any external forces Thank you

@sanhnghiemxuan7271 Год назад

@@pugalstech thank you, currently the controller is a 3 phase motor, if we remove the 2 sets of IRF 9540 and IRF44Z will it be possible to control a single phase motor?

@pugalstech Год назад

Yes possible, try the project sir

@topinfomentary6143 9 месяцев назад

Sir can this controller work on my ebike motor

@pugalstech 9 месяцев назад

Low current rating mosfets are used in this controller so it Is not advisable for e-bike applications