Homemade Soldering Gun 

"E" lams and "I" lams, such a simple and clever design. Pulled so many apart as a teenager back in the 90s - prepare for battle with a flat blade driver, a thin edged knife and a mallet to peel those silicon steel lams off that baby and break them free of the resin. You'll find it quickest to locate all the "I" lams first, align the driver blade with them and then smack em on the end by whacking the driver with a mallet and knock them out, leaving a gap at the end of each "E" lam, which you can then exploit with the knife, to slide between them and break the bond of the resin and slide them out with great ease (usually!) It's easier to practice it than to have me explain it. All the best, God bless you, Happy Christmas! Matthew. :)

i can hear the music says " get on it fail , fail, fail.... lol JK ... Good JOB project ! thanks ! :)

thanks again and yesterday I brought a simple soldering iron as i go to market

man smart and great

nice & thanks ..for my sold iron was not working I will make my own iron ✌👌👍

Nice project. thanks..!

Muinto bom obrigado. Austalia aqui é. Brasil.

Thanks so much to the tutorial

good job very nice

May be I should try this out. but I already have soldering irons and don't want to make one. good work brother...

Good job thk

Very good

Very nice videos .its tooo much good

nice job...👌

congrats for 100 subscribers

This is 1amp transformer and you can use more than 3amp of current . . I am sure that your primary winding is heated too much

thanks bro

gostei muito este cabo ficou top nuca imagina isto parabéns

nice

buen video amigo, like and suscribrer... saludos desde Venezuela

Bardzo dobry pomysł! Tylko nie wiem, dlaczego te grube przewody z transformatora do grotu lutowniczego są takie długie! Nie wystarczyłoby zrobić długość króciutką, np. 2-3 cm? Krótsze przewody to i opór mniejszy, mniej strat. Łapką up, Like nr 458.

Kudos, what about using smaller trany, say 3-0 or 6-0 so to be handy, and for a different need, whats the secondary voltage & current, if you kindly measure?

synthesis voiced

Great

😎👏👏

How do you protect the primary coil it doesnt draw excess current ?

thanks but any other appliciance

good bro

please give transformer instruction

I have a doubt ?.you didn't connect wire to the rounded wire.how can electricity pass

You should be show the secondary wire whether solid or multi wire cable...?

whats the working principle Sek. will the insulation on the secondary coil not burn with the heat...?

How do u know how much wire and what size wire to wrap. I tried it and I get a big n loud bussing sound.

can we make it from voltage stabilisers transformers

What gauge wire is used on the primary

i make a test of this for a welding 1st to chech the output current but when i shorted the secondary for just 2 secs the cables went heated , sooo if u want to caught fire , feel free to use xD

fu--king sic thanks

Hey can I use 14 gauge to this?

What's the difference between Soldering Gun and Soldering iron ? Is that safe ??

Is this safe? No. Does it work? Yes. A soldering gun is just a transformer with a trigger and a case.

Is it permissible to use an original Panasonic 6v ? and thank you

don't worry bro I've much knowledge about electric

clinically insane.

sorry can i know..if the transformer that power up by ac directly from main supply,are then all the metal plate core and covering section is danger to touch because of the LIVE wire had attached on it?..sorry my broken english,i know it was too bad..btw nice and simple but smart and creative project..such a clean lesson..thump up's..

What's the power rating?

In india we have 230v/50hz. Supply. Will this work as it is?

please tell me in which aplicaince i can find a transformer.you uesd in this video

hi sek..great video... can i use my old cpu psu and the cable with coaxial standard cable ..thanks for your great answer..and one more can you make a tutorial video how to make a esc bldc..thx

its great idea dude...

This transformer is 127 v input 12 v output , sorry for my english.

good tank you i no i no

would any transformer do? im afraid to do this because im thinking that i might get electrocuted or the thing would explode

Gardaş bunun ömrü uzunmu oluyor

what does he think his doing

Will still wire work instead of copper

Hola, tengo un transformador de ouput 122 v y input 12 v, si me servira

can i use 6 to 9 volt transformer

I make this but i havn't test this

can i test

Better build yourself from cheap chinese clones Hakko 936 or T12 handle, this seem too dangerous if you not careful, you can get that handle for USD2-3 and build the controller or buy the controller diy kit and use the transformer to power up the controller and the handle

gostei tenho dois transformador aqui vou ver se dá pra fazer

i subscribed

Is 9v 2A transformer is suitable for it

1 question ..why you can't use the transformer like it was ? but u have to remove the secondary !

What music is that? upd. Ever Felt (Part 1) - Otis McDonald

gud

Hy i maDe this soldering iron but cannot woRk i plug my trNsformer n it vibrate

المحولة 12 فولت هي كم امبير

No its not safe Risk of electronic shock Do not try frends

ilang watch ba yan boss, oks lang ba yan khit walang switch, baka kasi masunog kagad ang tip e

which amp transformer are u using

key on-off ?

hay

Where can I find that piece

is it safe for me to make and work for a long time with it pls tell me i am 11yrs old

what us that black wire

how many watt is the soldering iron

The main problem is heating problem

how do I know which wire (primary or secondary coil?) to connect to which wire on the power cord?

which wire you used as tip

Adress dena

It is real or fake

Wher am I going to get the transformer

How is this even possible.

use 220v o 127v? in you house

At 2:22 what is it called?

can I use 9v 1 amp transformer

very nice job done my friend please can you tell me how translate your language to english

A transformer make sound when it's switch on

Why fail... Fail... Umm... Fail... Faill...??

kuya anong part ng transformer yung tatangagalin at

tembagae di buang sampek habis itu tah atau separuh nya

what's with the fake voice recording? the spool will melt after a series of solder, the same time the heat that it will generate is not enough for heavy duty soldering because of the small amount of wattage.

Yaar Isse koi FUse to nhi ude ga na\ Aur yeh Current to nhi marta aur baki soldring machine jaise

It's not working very dangerous for you so don't make your home it's only work 2 minutes then blast very dangerous

почему изолента не синяя

maine yeh U.P.S se liya hai yeh kaam to karega naa plzz yarr comment faster i wat to make this!!!!

isme ac connection kese kiye samagh nahi aaye

this working only 5 minutes and then all Plastic parts will be melted lol

why don't we get shock from this soldering gun please say soon