Honda Civic EK - PROJECTOR retrofit to OEM headlights full installation guide

Подписаться 9 тыс.

Просмотров 26 тыс.

50% 1

There is nothing like OEM quality and fitment when it comes to lighting - so instead of buying a set of aftermarket projector headlights, i rebuilt the original leaking Stanley's and they turned out amazing! Whether you're needing a guide on resealing your headlights all the way to retrofitting a pair of projectors - this video has it all from start to finish.
If this helped you, let me know by leaving a comment and subscribing to the channel :) Thank you!
Parts used in this video
1) Morimoto Mini H1 8.0 projectors www.morimotohid.com/morimoto-...
2) Morimoto Motocontrol BI-XENON: H4/9003 www.morimotohid.com/morimoto-...
3) iilumo Iris shrouds + shroud centric rings www.iilumo.com/products/iris
4) iilumo POWER NOVA H1 HID conversion kit - 35w, 6500k bulbs www.iilumo.com/products/h1-po...
5) iilumo butyl premium headlight sealant www.iilumo.com/products/butyl
6) Duplicolor gunmetal grey
7) Duplicolor plastic primer
8) Duplicolor clear coat
9) JB-weld 50132 plastic weld epoxy
TIMESTAMPS
00:00 Intro
02:58 Headlight baking and disassembly
07:07 Paint headlight surround
09:28 Morimoto projector install
14:34 Testing and aligning projectors
16:15 Headlight reassembly and sealing
19:47 Outro

Авто/Мото

Опубликовано:

24 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 87

@abc09874 10 месяцев назад

Perfect, am about to do mine, and this gives me much more confidence in attempting my retrofit!

@JCYT 10 месяцев назад

Good luck with it!

@cgrschannel7256 10 месяцев назад

Car looks absolutely mint! Pro 👌

@JCYT 10 месяцев назад

Thanks CGR 👊

@thebiggestmac4202 8 месяцев назад

These look so good!! Thanks for the video, I can’t wait to do this to my Honda fit!

@JCYT 8 месяцев назад

No problem mate! I think this applies for other models too i know a few people who have used the vid to do EG lights. Good luck

@Shreddylife 9 месяцев назад

They came out nice. I think black would have looked better then he gray personally but they still look nice. I ended up buying gunmetal ones for my 1999 coupe because its Milano red and I wanted the JDM look. I am very happy with how mine turned out and the projectors are so much brighter then stock!

@JCYT 9 месяцев назад

Hey mate thanks! I agree with you It's grown on me but i'm still not happy with the colour - eventually will pull the shrouds back out and do them in a colour someone had recommended (looks like ek9) I'm loving the light output that's for sure!

@twd892 5 месяцев назад

The angle is intentional... It's to direct the beam down on the oncoming traffic side, up on the pavement side. If it's level, you're just blinding everyone coming the other way😂 The gunmetal grey looks sick tho

@tylerlorence6209 5 месяцев назад

Everyone’s lights are blinding fuck it

@JCYT 5 месяцев назад

You are talking about the cut off plate. Yes that step up is intentional. But no the beam pattern needs to be calibrated to the horizontal.

@JCYT 5 месяцев назад

Gunmetal has grown on me but not convinced yet haha

@Unbranded2k20 6 месяцев назад

Dude! i want to thank you for this video! so much info i was looking for! thanks!!

@JCYT 6 месяцев назад

My pleasure mate!

@dC5alex 6 месяцев назад

The scotch pad creates scratches the surface to help promote adhesion for the paint and primer. Also, I recommend blackout and lightly mist some metallic dark grey.

@JCYT 6 месяцев назад

Thanks for that!

@champchamp1774 10 месяцев назад

Nice man!!! Im going to do the NHK in mines. Think about using those led strip headlights they got lol

@JCYT 10 месяцев назад

Whats NHK? I kinda wish I did the light up shrouds for the fun of it but completely unnecessary. Good luck with it!

@ShereneMc 4 месяца назад

I need this whole series for my civic 😭 I have the same model

@antn8387 4 месяца назад

great work man

@JCYT 3 месяца назад

Thanks mate appreciate it!

@mecanicageneral615 7 месяцев назад

I tried 55w ballast xenon, and then led CSP chips 3570 H1, 3 times brighter.

@dufonrafal 6 месяцев назад

Nice, but why the H1 and not the much better micro D2S ?

@Gamer_Marcy_God 10 месяцев назад

Looks sick Fong Pei

@JCYT 10 месяцев назад

Thanks Ahoyhoy

@erickruiz-hl5vs 5 месяцев назад

Simple & clean 🔥🔥… got 6.0 morimoto… but think it’s ready to upgrade 🤔🤔

@JCYT 5 месяцев назад

I could recommend these!

@TheDarknessConsumesMe666 Месяц назад

If you do want to upgrade it in the future, can you show how to install a switchback LED shroud?

@JCYT Месяц назад

Sure can! It was definitely a though. But wanted to keep it relatively subtle

@danielthomas1526 10 месяцев назад

Looking awesome bro. Lets do my FD now

@JCYT 10 месяцев назад

Hahaha yeah had some naughty thoughts about doing the RX-7 too

@danielthomas1526 10 месяцев назад

100% we can do mine as its not going anywhere soon, so if we stuff it i have time to fix it. 😂

@Oktheorignal Месяц назад

One piece of advice. Start your paint spray pattern away from the headlight plastic and stop it away from the headlight. Will prevent any nozzle splatter!

@JCYT Месяц назад

Hey mate! Sorry for the slow response. That's good advice thank you! Will try for future projects.

@Aaron-jd1cb 2 месяца назад

Use oven cleaner on the chrome plating to remove it completely if you are painting the entire shroud. The paint sticks much better than over the chrome.

@JCYT 2 месяца назад

I must try this! Planning to do another set soon

@johnnytrannnn 6 месяцев назад

I like the grey. It's different. But black is cleaner

@waelabdula7922 2 месяца назад

Looking to this to my X3, does the shroud & lens have to be made for the car? Or can I use a universal one?

@JCYT 2 месяца назад

Hey mate the shroud and lens should be a universal fit. But you will need to figure out if the whole package (projector and shroud) will fit into your housing.

@Shreddylife 10 месяцев назад

How do you get the high beams to function with a setup like this? That is the main thing I am confused about. Will I need a aftermarket relay or something? Thanks for the video

@JCYT 10 месяцев назад

Hey mate Yes it is all controlled by the motocontrol harness. The harness receives high beam signal from the factory H4 connector which switches a relay to lower the cut off plate (high beam). It doesn't look difficult to make a harness from the factory loom but it was easier for me just to buy one off the shelf. Good luck with it

@Shreddylife 10 месяцев назад

@@JCYT sweet thanks for the reply

@michael-angelogarnett8658 5 месяцев назад

Thanx for the video btw.. I’m jsut trynna get a much better understanding of the clerical work before I decide to do mines.. I don’t want my dumb Mercedes to throw codes and not push power to it.

@JCYT 5 месяцев назад

What merc are you retrofitting projectors to?

@dustyfarmer 10 месяцев назад

Nice, not roadworthy, but nice. Before you order some projectors for the Landcruiser try some Philips +200% H4 headlight globes. They are A.D.R approved approved (or the packing is as it says so) and they have much greater range & brightness than standard globes but the light throw is correct, crisp & clean & no other drivers have ever challenged the low beam brightness at night. I'm a big fan of projectors & did plenty of research to see if I could get them legal on my 79 but what it boils down to is unless they were fitted as standard equipment they are not allowed & to get them engineer approved is big bucks & lots of testing.

@JCYT 10 месяцев назад

You read my mind Dusty! I told myself i would never put projectors on the 79... but i seriously considered it after finishing this set. That is true, unfortunately would never be road legal 😔 Thanks for the recommendation i'll have a look. I actually really like the 3700k bronze look of the factory globes but was recently in the high country and i would have been stuffed if it wasn't for spotlights. Wish the factory headlight had a better output.

@dustyfarmer 10 месяцев назад

@@JCYT I reckon you'll be really happy with the performance of the Philips +200% H4 globes in the standard 79 reflectors. Much whiter light and you can actually see where you're going on low beam at night & high beam is much improved too.

@JCYT 10 месяцев назад

Just ordered a set haha Philips RacingVision GT200 3600k

@dustyfarmer 10 месяцев назад

@@JCYT I use one of those telescoping magnetic pickup tools to assist in removing & replacing the H4 globes after you remove the plug, rubber boot retaining spring as they are in a tight spot . If you like them order a spare set so you can change out a blown one as they occur.

@edwinvillegas7650 5 месяцев назад

what is the size of the projector you installed. Is it 2.5 or 3. What do you think is the correct size for a 2009 Tucson. Thank you.

@JCYT 5 месяцев назад

It's a 2.5 inch No idea re Tucson sorry

@winniewong2353 10 месяцев назад

I heard a boosted D16 goes alright 🤗

@JCYT 10 месяцев назад

say no more

@vongdong10 8 месяцев назад

I wanna do this too but don't have an oven for it. Could alternatively buy modded ones but that's around $1500au landed!

@JCYT 8 месяцев назад

Hey mate, yeah the price is ridiculous! In my research you can open the housing with a heatgun. Be careful not to burn the headlight of course!

@ixCGAMExi 10 месяцев назад

I would love to do this to my del sol, but I'd honestly rather have LED instead of HID. Having trouble finding some though 🤦

@JCYT 10 месяцев назад

I haven't seen anyone do them on a delsol! Would look sick.

@zrontv 7 месяцев назад

There’s a led projector from SINOLYN

@JeremyHansen 5 месяцев назад

Morimoto has their M LED 2.0 Projector for retrofitting.

@antoniop5889 2 месяца назад

I’m confused on how to align them. I bought some retrofit projectors on Amazon but theres no instructions on how to align

@JCYT 2 месяца назад

Hi mate Do you mean the alignment of the cut off plate so they sit in line with each other parallel to the ground? You need a dead flat concrete slab and a straight wall. Park up facing the wall and measure Draw a line parallel to the wall and essentially you will need to switch the bulbs on and rotate the projectors to the right angle 0 degrees to the ground. Good luck.

@antoniop5889 2 месяца назад

@@JCYT the way I was thinking before I take of the old ones off. I’m going to put some tape on the wall to where the old ones line up. Than going to put the new ones with the retrofit fit and manually aim them. So basically you have to do it manually? Once I’m done than I’ll seal them up??

@JCYT 2 месяца назад

@@antoniop5889 yeah defs that would work. Don't stress too much - you can still get some adjustment once it's all sealed up. Obviously try to get it all square before sealing.

@AiiRSTRiiKEOFFICIAL 7 месяцев назад

i have a 2000 honda civic ,how do i know which hid kit to buy?

@JCYT 7 месяцев назад

Hey mate Would be the same thing across all civic ek. If you start off with factory H4 housing, you'll need a universal projector to suit a H4 housing. Check compatibility from where you purchase them from. Projectors will convert your old H4 housings to suit newer styles of globes like H1 and D2S. It really depends which projector your purchase. Hope this isn't too confusing

@AiiRSTRiiKEOFFICIAL 7 месяцев назад

I WAS THINKING OF BUYING( Nilight 2.5" Mini Projector Lens for H1 Headlights Bulb Retrofit, Custom Headlamps Conversion:Chrome Shround) CAN THIS WORK?

@EnasiAU 10 месяцев назад

10x better than ebay headlights

@JCYT 10 месяцев назад

Was definitely still tempted by eBay 😝

@EnasiAU 10 месяцев назад

@@JCYT cant beat oem quality!

@michaelpaterson8086 10 месяцев назад

Yo yo bro, im desperately looking for a driver side window regulator + motor ASSEMBLY just like you guys in Aussie, I have a RHD civic too but trying to find a decent quality aftermarket window regulator + motor ASSEMBLY is like gold dust here in UK. Please help bro, any recommendations there in Aussie? The only option i currently have is original Honda regulator + motor which ain't cheap 😢😢

@JCYT 10 месяцев назад

Hey Michael We do have them floating around but it'd probably be too expensive to ship to the UK. Prices are going up though... Usually sold in a full kit with the power window conversion - i've seen them going for about 600-700AUD including the harness and door trims etc.

@michaelpaterson8086 10 месяцев назад

@@JCYT Cool bro, whoa that's crazy expensive though 😂🙀. Just to confirm bro, what I'm after are window regulators with the motors as an assembly (so electric operated windows) in quality aftermarket preferably. Amayama original Honds regulators and Motors currently is my only definite compatible choice after getting 2 none compatible aftermarket brands, Dorman and Electric- Life

@michaelpaterson8086 10 месяцев назад

@@JCYT And yeah bro, looks like most probably better just ordering parts from Amayama Japan, atleast they are guaranteed to be correct...

@JCYT 10 месяцев назад

@@michaelpaterson8086 could it potentially be cheaper sourcing it used from Japan/Australia even with freight?

@michaelpaterson8086 10 месяцев назад

@@JCYT That is an idea however bro in my experience this is a high wearing part and so used regulators would most probably be on their way out. It's usually the drive teeth in the motor and the drive teeth on the regulator that break or smooth down.....