Honda GX 390 Engine Disassembly 

Best gx390 rebuild video. I rebuilt motor following your assembly and disassembly videos and saved 400 in labor 😊 Thank you!

I've used this sprayer several times now on brick pavers, a wood deck, patio, and a driveway. ru-vid.comUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX It has performed as expected on all surfaces. For larger areas like the decks and patios, I think I will be looking into a surface cleaner attachment to speed up the job, or at least make it a little easier. Hose and sprayer connections are tool-less, tight, and quick. I used the yellow nozzle on the concrete/brick surfaces, and the pressure was adequate for cleaning those surfaces.I am disappointed that these units are still being shipped with a nozzle storage holder that allows them to vibrate out of the holder way too easily and become lost, but I don't want to knock off a star for that reason. The functional part of the washer works very well, so I would recommend this product.

Thanks I have a low oil sensor bad on a GX390 which I disconnected so engine will run. To much work to replace ,thanks for showing it internal inside engine

I wish the ones I take apart look anything as good as those 😂

Fantastic, Crystal clear video. Thank you!

I was wondering why so much heat was coming out of the side of our engine. You're video explaining the fan pushing air through to help cool the block makes total sense. I thought a gasket might have blown.

Thank you for your time of the instructions very helpful , blessings

Que buen motor ,,,es honda no hay con que darle

Español ? Subtitulos o traduccion ? Por favor gracias 👏🏻👏🏻👏🏻

well explained thanks for sharing

Very informative. Thank you. Was that residual oil still left in the bottom of the case after draining?

Nice Video, i couldn't figure out where the decompression thing is. must be somewhere on the camshaft?! Let me know if anyone does know that. Thanx

I watched this movie well. I have one question. After removing the flywheel, there is no charging coil???😊

very nice video...I have a issue I hope you can help me with. I have a Honda GX390 on a generator. I replaced the crankcase shaft oil seal as it was leaking. I installed in flush with the engine case. After running for awhile it started leaking again. I thought the seal needed to be counter sunk a bit so I replaced it again. And after running for a short time it has started leaking again. Im not sure where to go from here. Both times replacing the seal I used steelwool to clean the shaft and it seems smooth with no defects. Any advice would be great! Thanks in advance

This is really cool

You don't need a puller to remove these flywheels, just put the nut level with the thread end and then one solid tap with a lump hammer will remove it.

Great explanation thank you

hi what size and model and brand is 3 jaw puller. if you are using snap on or OTC pls do provide me the 3 jaw puller name and model

Thank you very much big man thank you for your nice tutorial 👍 I really appreciate you sharing your great knowledge.

Nice job.

I have set up my trailer so that it’s difficult to change the oil on the gx390. Would a suction oil extractor be efficient? Is there access to the bottom of the pan from the dipstick? Just want to make sure I don’t leave too much residue behind at the bottom by not using the drain plug

Great video and explanation. How can I send you a PM on information on your sponge organizer for nuts & bolts.😀

Any difference in the black shrouded GX 390s ? Looking at a woodsplitter with one on it...thx

Good video

Could you leave all the flywheel etc fitted if you need to inspect the tappets/crank?

What is the final rpm of this machine after the gear transmission?

Thanks

Do you happen to know if Honda has an electric start kit for a 2012 or later Honda GX390. All the kits I have found online (Amazon, Ebay, etc.) are for a 2011 or earlier model year. I know Honda currently offers versions of the GX390 with electric start, but cannot for the life of me find a kit for one that didn't come with from the factory. I know the flywheel and I believe the coil is different on the 2012 and later models. SO FRUSTRATING!!!!

The cam shaft won’t come out for me what do I do?

What causes Gx390 to swallow fuel

re coil hard to pull on my Honda GX 390 8 GPM pressure washer only 7 mos. old

hello i have 11 hp engine i have two yellow wires coming from carburetor! where should i connect them?

giveaway?🙂

Your entire video so far is soundless. Like one of those old talkies. Not even muzak.