Honda XL1000 Varadero - I have found the problem - Part 2 of 2

Подписаться 8 тыс.

Просмотров 11 тыс.

50% 1

Honda XL1000 Varadero - I have found the problem - Part 2 of 2
Continuing on, i want to go a bit further into the engine, just to make sure everything is ok, so the next job is to remove the front cylinder head
Follow me on my Facebook page, all welcome to stop by and say hello :-
Hindicobra-669625496577879/
Help me grow and continue by becoming a Patron of The Amateur Bike Builder
Click to join the team.
/ theamateurbikebuilder
You can now follow me on Instagram
/ theamatuerbikebuilder
Alternatively If you just want to say thanks for this video alone,
you can drop a dollar in our "Tip Cup' by using Paypal to hindicobra1969@gmail.com
The money will go to make more videos / buy parts and supplies
Link to my Merchandise shop
teespring.com/...
If you haven't already,please remember to Subscribe -
/ hindicobra
Check me out on Twitter :-
/ hindicobra

Опубликовано:

16 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 18

@cemkomsuoglu7919 4 года назад

Lessons learned , without expecting to hear nasty noises better to change the tensioners (preventative maintenance) , Thanks for the videos 👍

@TheAmateurBikeBuilder 4 года назад

Thanks Cem, both tensioners will be changed, appreciate you comment

@shaunholbrook2288 4 года назад

great to see you get to the bottom of the problem, and hopefully not too expensive

@TheAmateurBikeBuilder 4 года назад

Cheers Shaun, You and me both! will be a few hundred £ just in parts, labour is free though

@Desertduleler_88 3 года назад

Use the one stop method of using a piece of 8mm steel rod measured accordingly inside the tensioner between the worm screw and the plunger head. You will need to take measurements once the tensioner is under load by making a tensioner key. By using this method you get the benefit of using the original auto tensioner without the catastrophic damage if the tensioner fails, the tensioner plunger won't fully retract inside the tensioner housing.

@TheAmateurBikeBuilder 3 года назад

Thanks, handy tip. will keep that it mind if it ever happens again

@banditnev 4 года назад

Seen a lot of cam chain tensioners replaced it isn't uncommon. At least it other parts look okay.

@TheAmateurBikeBuilder 4 года назад

Thanks Banditnev, want to have a closer look just to make sure, but the heads look ok

@geedee4 4 года назад

Result! 👌👍

@TheAmateurBikeBuilder 4 года назад

Thank you! Cheers!

@lakbeschermingonline5485 2 года назад

Install manual tensioners , APE or other brand. Big problem also with the Firestorms ( 99% same engine) the automatic ones fail , specially front cilinder . Automatic ones = Russian Roulette....

@TheAmateurBikeBuilder 2 года назад

Appreciate the info

@leszekm4414 4 года назад

just replace the spring itself. much cheaper solution.

@TheAmateurBikeBuilder 4 года назад

Thanks Leszek, with the age and mileage on the bike, i would prefer to replace the whole unit

@bertzx9r894 4 года назад

On a daily bike i dont think its worth scrimping. Already lucky that it hasnt caused the chain to jump and damage valves and the piston. Best off buying new, maybe even manual adjusters.

@TheAmateurBikeBuilder 4 года назад

@@bertzx9r894 New ones on order

@waynemrees8240 2 года назад

So you removed the motor to change tensioner! Epic fail!

@TheAmateurBikeBuilder 2 года назад

Only removed the cylinder heads, as i said at the start i didnt know what the problem was as the noise was coming from the rear cylinder, if i had known it was a tensioner then i wouldnt have stripped the engine, but considering the bike has 96000 miles on it and i did all the work myself not to much of a problem, more a learning experience