How I Built My Home Made Rock Crusher 

Thanks for explaining everything in such clear manner. Maybe some time you can do a short video of the crusher running with the front plate removed (of course without throwing any rocks into it). Anyway, that's one of the best vids on the subject around.

Excellent idea. An expanded steel safety guard over the belt would be a nice addition.

honestly, great video. clear, concise and great build. Easy to understand and follow. Thank you.

That's a nice machine you made, well done.

that was very helpful, thanks!

Actual measurements would be really appreciated

Some good tips, thanks.

I believe you should add a reservoir and 1/4" dripline. Such as would cut the dust to minimum. just a small tap, like used for adding a line to your refridgerator from your potable water source.

Hi Puddin, what a great job you did, can you please tell us the Width and length of the shaft and also what size bearings.

I like it! One thought, and one question: The thought: Have you pondered adding a nut and bolt to the final link of chain, to give the flails a better head, and: The question: What RPM are you running the shaft? I'm going electric.

Good work, wanting to build slightly bigger on to crush glass here in the Philippines.

Excellent video! Which diameter did you made the holes in the wall? 1/8"?

Very nice job mate.jas

Nice job.👍

RE : The Dust Exhaust Pipe ... One idea you might like to try is to weld on a metal sleeve to which you push the Duct Pipe onto ... hold it on with a large metal pressure clamp ring that is much like a hose clamp but larger !!

Good job brother, get a green belt from the parts store, they are for heavy use. And drill holes in the bottom for your heavier ore will sink.

good video

Flanged pillow block bearings.

I'm thinking of making such a mill. In a 50 cm diameter mill, what is the power of the gasoline engine I'm going to need?

What diameter of shaft did you use and was it keyed? Also what was the outside diameter of the pulleys?

Are the chains long enough?

What do u think of running it as a direct drive? Did you overlap the steel, 135’s.

Planning my build.. Would holes on the bottom 1 or 3 plates for the processed material to fall be better. Gravity usually makes things fall down. I'm thinking a bigger flale shaft would be better to maybe 1 inch? Would horizontal weld lines on inside plates help brake material better? What would be a better/harder material than chain or attached to end of chains?

If you put a glass on the pulverizer machine , will it still work ?

Excuse master, may be can u send me technical draw that cruisher. I wanna made that. Thank u.

How many barings do you need?

For where you put the sticky tape I would actually go and get myself a 3-inch fight to a 6-in pipe and weld it and then make it so there you can slide a pipe onto it and take it off if you want

Results of your crushed materials. As in size ? Microns ? Chunks ?

Have a look at a Metso product called a knitter crusher - very similar in principle 😎😉

you can make a tensioner on the belt

Building chain impact mill here. . . .Just wondering what size drill holes you have drilled for your exhaust port. . . . and how many. . . .I did my barrel out of 500mm x 150mm (20" x 6") line pipe that was 10mm (3/8") thick . .. . .my first attempt. . . ..my shaft is 25mm (1") and chain is Grade 8 HT steel Galvanised . . . . .Still got a way to go. . . .Have plans of coupling this to a recirculating wet sluice. . ..As I live in a dry region of South OZ. . .

How far between chains and inside of box?

What's the engine type and hp

What is the point of turning a rock into dust? I guess I don't understand the point of this machine.

why not use a carrage bolts inside ..!??

how much to make me one?

But where is the ground terrace comes out?

imma gonna build me one 😊

How deep is it 8 inch deep 10 inch deep?

I spent two seasons in the octagon.

I got a question would this crush mountain rock in Virginia

Hi Sir, any chance you would be in a position to assist me build one of my own. Am in Kiambu Kenya

I need help building a stamp mill. Want to collaborate?

Hello thank you for the great video, if it is not a problem for you, can you send me your drawings on rock crusher width brace, kind of like drawings, thanks in advance

i wonder why are they so expensive >.>

Hey! Can you PM me everything I will need to build such a rock crusher dimensions, part names, etc? I want to build one as soon as possible. You can also add my Facebook if you're interested. Thanks!

This guy has never even built a dog house.

how thick is the body

Are you willing to make me a crusher

why not use an electric motor?

😂😂😂😂😂😂

fix yr cam pls