Pues ahi el problema real es lo pobre de cemento de el piso mejor quedaría romper y hacer un pequeño castillo ,no se que es lo que va a detener pero evitaría que un viento lo tumbe
a Builder would have used a large Hole to place a threaded insert. and repour it in cement than base that poal on a threads too make you eble to level it and reajust it in a few yrs after it sank into the groud a bit
@@Rubberduck-zt8lm WHICH SCHOOL KIDDO?😂😅 HAD YOU BEEN THERE?😂 I'M A BACHELOR IN INTERIOR DESIGN ADN CONSTEUCTION.. NEVER BEEN TAUGHT ABOUT THIS KIND OF CONSTUCTION. IT'S ABOUT PROBLEM SOLVING KIDDO... SO YOU HAVE TO BE CREATIVE WITH YOUR BRAIN.. IF YOU HAVE ONE 😂 WATCH IT KID... YOU CAN SEE THE CEMENT LAYER ISN'T THICK ENOUGH.. THE BOLTS ARE LOOSEN OR SHAKING THAT'S WHY HE GAVE DIAGONAL LONGER STAKES TO MAKE IT MORE STABLE. HE.WOULDN'T HAMMER THOSE STAKES IF IT'S FULLY CONCRETE. THE FLAT SURFACE OF THE PLATE GIVES MORE GRIP TO THE GROUND.. MAKES IT MORE STABLE RATHER THAN ONLY HOLLOW POLE.. SURE YOU DON'T KNOW THAT..😂 ALSO THERE IS POSSIBILITY THAT THE POLE ISN'T CUT EVENLY OR STRAIGHT.. WITH THE BASE PLATE HE COULD ADJUST IT. HAVE BEEN IN CONSTRUCTION BUSINESS FOR ABOUT 25 YEARS. HOW ABOUT YOU? WHICH SCHOOL DID YOU GO TO KID? I DON'T THINK TOU CAN EVEN HANG A PICTURE ON THE WALL 😂😂😂 THERE'S NOTHING WRONG WITH THIS VIDEO.. IT'S JUST SMARTASS IDIOTS WHO MAKE IT LOOKS WRONG 😂😂😂
WHY WOULD YOU NEED TO REPLACE IT ANYWAY? MOST POLES ARE NOT MEANT TO BE REPLACED FOR A VERY LONG TIME IF IT REALLY NEEDS TO BE REPLACED YOU CAN JUST GRIND IT.. THE PURPOSE IS TO MAKE IT LOOKS NEATER AND STRONGER FOR SURE..
Забили тупо прут стальной и думают, что он будет держать? Так только глупцы могут сделать. Потом от ветра всё завалится или когда кто-нибудь облокотился. Бред для идиотов.
Ok….. 🤦🏽♂️ Don’t do this people. Besides the fact that 90% of people don’t have all the equipment to do such a stupid thing, just don’t do such a stupid thing😂🥴🤦🏽♂️ Now you gotta cut the dam thing when you need to remove it instead of bolting it to make it easier. My goodness
This is done by a low class welder and not by a professional one. Professional welders will not use such poor quality materials and even do a bad workmanship. 😂😂😂
Why is there 100k likes on this video there's no way that is the correct way of installing a post. Why not make a plate w/ holes for the existing anchor bolts?
En la 1a piba. De resistencia, movió la pza. Desde la parte a arriba, en la 2a. Pba. La movió en la parte de abajo. Así que e me quede con la duda si funciona o no el trabajo.
Igual no sirve debe de hacer una fundación con una plancha metálica y después que esté firme proceder a fijar la columna y así puede garantizar el trabajo
What did i just watch....man people are ignorant. You had the correct anchors to begin with all you needed was some flanges welded on the post..drill some holes in the flange, slide it over the anchors and tighten the nuts down.
Da risa este video aunke hayan metido una varilla de aprox, 10 cm, de nada sirve mientras lo hagan en piso flojo una buena recargada y se sale demos buenos ejemplos no basura k de nada sirve
Mejor es fundido con cemento, con una platina y dos pernos de acero inoxidable en el suelo y en el tubo también una platina con huecos, los une y les ajusta con las tuercas, ahí queda bien
