How To | Auto Transaxle-Output Shaft | Auto Trans Output Shaft Seal | Install 

Thanks, that means alot

Thanks for watching and the comment

your welcome, and great info on the tie rod tool trick

Happy you found this video helpful. alot people think silicone is bad, but as it gets pressed in most of it gets mashed off the seal and what stays is only whats needed if they are bad places where the seal goes or misshapen due to heat depending on what you working on

Why do my axle make a hum noise? Differential doesn't leak. Transmission is fine. Hub bearings a a year old...

wheel bearing, or axle nut to tight

@@TattsForLife yep. I over did it. And had to repair or replace the hub bearing again.

yah, thats a pretty common thing happens, I see it alot

Thanks for watching

Thanks good info, and it never leaked prob because of the sealant

sometimes u can insert the old axle and pull, if not you can hook some vice grips on it and pull

Thanks for watching!

You are welcome!

been so long since I did this repair, most likely its the silicone called right stuff

@@TattsForLife thanks and keep on rockin!

@@andrewhudson3723 Thanks and you to

Right stuff bonds to anything

@@TattsForLife Is it Right Stuff Gasket Maker (Like 90 min gasket Maker e. g.)? Thank you.

what accent? everyone sounds the same down here lol

Maybe deep south Louisiana

sometimes you can use a old shop rag and vic grips to lock on to the shaft and pull it out

@@TattsForLife you did the best illustration with the snap pliers but most ppl don't have snap pliers so if you don't mind I think you should do an example with the info you just gave me nobody on RU-vid is explaining this literally

I will if I half to do the job over again, I plan on redoing the car and paint and stuff in the future on the channel@@jazzysmith2430

@@TattsForLife I'm glad to see you are still active with the video.. I'm up to my neck in a cv axle replacement and doing the seals at the same time. Couldn't find information about that new seal surface for the stub, like how to replace it. Like how you showed that part, but how in the world did you get the old one off the shaft without a press? Did you cut it off somehow? I'm thinking about freezing the whole thing, and pouring hot water on the seal surface to try and slide it off the shaft.

@@jazzysmith2430buy some

Thanks, it was not the best video, but it may help someone out

+TattsForLife Definitely! I think it turned out great

Thank you

it usually comes out with the shaft. I have replaced the axles before, but not the seals. that was what I was here for. Hope it worked out for you.

Always welcome

you could try a socket or a pair of channel locks that are ioen

Glad to help

Thanks a lot!

can you get a sliding hammer on it? to knock it out

I dont remember, been a long time since I made this video, sorry

Its a 30 mm because I just did this same job myself this guy explains it great.

Welcome

I think the difference is the year of the car.

I think your right

😱

its duck tape lol

Thanks man

Thanks

yep

Happy you liked it, was a very simple video

TattsForLife hi!yeah i liked it.simple but very informative😊thanks for sharing😊have a good 1😎😊

Thanks

cause it one of many amazing things in life

Its called a speach Impediment

Same reason one would put rtv on a push in seal

They have a speech handicap.

Down south we country folks downhere

it just takes some time get use to installing seals that way, lol you get use to it when you dont have a seal driver

Thanks for watching

Thanks for watching, its all in a days work lol

Thanks

great info

Look BzB 315, the only people going to see this video are those who are trying to fix this auto problem themselves, and the content creator. We all see it once, maybe twice if ya get stuck. But Tattsforlife will see it far more times. How dare you ridicule someone who is helping you for free. You didn't just arrive here randomly, you had the specifically have a question about something this man took his time to explain and show you in a helpful and thorough manner. This specific transaxle is extremely difficult to find quality videos about. Who are you to say a got dang word about how that boy talks. If your mother hadn't taught you better than that, BzB 315, she must be just like you. Someone who's only way to feel good about themselves is to put someone else down. I'm sorry you weren't raised better than that. I'm sorry your mother and father weren't capable showing you what it really means to be a part of this earth. To be part of what makes us human is to BE human. A human with thoughts and feelings who respects and listens to others humanity. Your a beautiful human, Tattsforlife. I hope that this human here made your day like you made mine. Thank you for showing me I didn't have to buy a $250 application specific tool. May your heart stay calm and your conviction burn fierce. BzB 315, hopefully one day someone gives you a reason to be human.

out of shape 😑

Maybe just smoked a big fatty😂

Huh

😑