How to bind to Eachine mini P51D with Radiomaster multiprotocol Radio F4U corsair 400mm RC Plane 

Older video but exactly what I needed so I can fly using the one radio for all my planes and drones. Thanks

Thank you so much!! I’ve been trying to figure this out for months!

This was a massive help getting the gyro switch sorted. Great video. Thank you.

Thanks for the video. You may know this by now but you don't need to create three entries in the mixer for gyro. You can just set the source as the switch and leave the "switch" section blank. Depending on the switch position you'll get -100 0 or 100 as the output.

Very helpful. I use the receiver boards for scratch building and did not know how to set them up on my Radiomaster 16. Great

Nice, thanks for letting us know. Fly Safe!

Awesome, I have radioking tx18s but very easy to follow along. Almost the same transmitter's. Just gotta go test out the stunt button to see if it works. Thanks

Just wanted to say thanks for this! Its prompted me to but the P51D.👍

Thanks a lot for making this vid mate. I'll definately be making use of it when my tx16s arrives this week. Cheers for the great vid.

Thanks a lot. This video is very helpful!

Great video! Thanks for the info.

That was really helpful . Thanks

Interesting technique to use Channel 5 weighting of -100%. I reversed the channel on the Output screen. Obviously the same thing. But shows how flexible Open TX is.

Hey! Great video! I was just wondering if you could tell me which multi protocol module you showed in the taranis x7?

Are you able to set up the stunt button for the plane with your Radiomaster?

Good day..sir how to set the throttle hold or of in that plane.

Thank you for this very useful video.if you could give my some advice since I have not been able to make link with the steps that you show. the only thing different is that my radio is mode 1out de box an de plane is in mode 2 thank you so much

Can the tx12 bind to these planes as well?

The 3 mode switch does not seem to work with the XK T28 or P40 planes. The gyro won't disable :(

Hi. How i Will configure the acrobatic Button? Please.

Received my P51 today. Binding with the TX16s works as described in your instructions. What I can't do is calibrate the plane's horizontal position. According to the instructions, both sticks should be held down and outwards and then it should beep. But the beeping stays away. Other stick positions were also unsuccessful. How did that work for you? By the way: I don't have to arm the motor as described in the instructions. The motor also works without arming

Does using the Tx16s increase the range on these planes? If I put an fpv camera in these little planes will I be able 4o fly further away? Thank you

Great vid 👍 How do you set up the stunt switch?

Hello, whene i bind, it will only work on low power mode? Is that safe?

Does it also work with edge tx

Yes great video for great planes! I struggle to set up the calibration on a 2-, position switch. How making it going from -100% to 100%? I can only go from 0 to 100%. I tried 200% weight, 100 offset, .. curve... But no success. Please help me....

I only wonder how did you find out the protocol these eachine/volantex mini planes are using? Is there a site out there with repository of different protocols?

Should you add expo with these little war birds to make them less squirmy and more smother and if yes then can you show how thanks

same for Radiomaster boxer 4-1 M8? cheers :D

Tqvm..gud explanation...my question can radiomaster tx16s binding with eachine F22 mini raptor?

Can I use this RadioMaster TX16S MKII V4.0 Hall Gimbals ELRS JP4IN1 Transmitter Remote Control Multi-protocol OpenTX And EdgeTX With this RadioLink R12DS 2.4GHz 12CH DSSS & FHSS Receiver for RadioLink AT9 AT9S AT10 AT10II Transmitter Support For SBUS PWM ?

I have a Volantex F16 Bound to my XT16S. When i first plug in the battery, everything is working as it should. i have all control surfaces on TRIPLE RATES through the INPUTS tab. I have THROTTLE CUT enabled on a switch to overide channel 3. But when i ENABLE THROTTLE, the GYRO seems to take over all my CONTROL RATES. And then the GYRO OFF SWITCH doesnt disable the gyro. I tried disabling the throttle cut function. Made a totally new MODEL SETTING from scratch a couple times. but i keep running into the same problem. As soon as the throttle kicks on, the gyro gets activated. Any thoughts on what could be going wrong?

I have a weird problem I've Done all the instructions but after binding there are no controls unless I click the range tab next to the bind . It only works when the range screen is open . Any ideas thanks

Are these the RTF version or BNF? CAN I BIND MY RTF ONES TO THIS TRANSMITTER?

Any recommendations on how to bind the eachine mini cessna 550? I was able to bind my Eachine TX16S to eachine trojan without issue, but when I copy the model in TX, rename and attempt to bind to Cessna 550, model doesn't respond.

I did everything like you, and mine does bind, but control surfaces do not respond, Giro is on. Control surfaces work when I put the radio in Range mode , can you tell me what to do ??

Why i need to rebind with Eachine mini plane every time on, is it nomal ?

Hi, I have a Jumper radio and have Bound these little planes ok but I can't get them to bind to the Eachine TX16s.. I have followed your Vid very carefully but they wont bind.. do you know if there is a reset button on the receiver in these planes?.. Regards, Pete

Hey blowy. I have the eachine version of tx16s - when I bind it, I can’t control any surfaces unless I use ‘low power mode’ option. Have you any thoughts on that?

Any reason you can think of why i have to keep rebinding the model?

My TX16S will not bind to the warbird. I've tried many things, followed your instructions to the tea. It just woin;t work. I even downloaded the latest internal module firmware

Mine binds but nothing works unless I put the tx16s in low power mode or range test then everything works but as soon as in full power nothing works apart from stabiliser

This protocol has problems but it seems to be fixed with the new updates. I know its a pain to update your radio or you can just put up with it. Links below WE had to re-bind to plane every time we wanted to fly AND a lot of trouble flying 2 planes together - kept binding to the wrong plane The Multi-Module Protocol info page link here - github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md And Multi-Module firmware update link here - downloads.multi-module.org/?rmtx16s

Dear Sir I'm trying to bind my mini trojan t28 to my radio master tx16 max. But it doesn't work. But as soon as I put it on range and press the scroll wheel it binds. Why is that. I followed your setting up perfectly. Help please Kind regards Johan

In ch5 you dont need to what you did, I just sent a switch in the 2nd line and it it gives me the 3 rates