Тёмный

How to change a front shock strut on PEUGEOT 208 1 (CA_,CC_) [TUTORIAL AUTODOC] 

autodoc.co.uk
Подписаться 392 тыс.
Просмотров 38 тыс.
50% 1

How to change a front shock strut on PEUGEOT 208 1 (CA_,CC_) 1.2 Hatchback 03.2012 - present [TUTORIAL AUTODOC]
Shock strut on CITROËN C3 III (SX) (07.2016 - ...) / CITROËN C3 Picasso (02.2009 - ...) / PEUGEOT 207 Hatchback (02.2006 - ...) / PEUGEOT 207 SW (02.2007 - ...) / PEUGEOT 207 Van (04.2007 - ...) cars should be replaced, as a rule, according to one and the same procedure.
However, there can be slight differences due to specific features of the vehicle design.
🔝 Top brands that produce shock strut: STARK; FEBI BILSTEIN; SACHS; RIDEX; MONROE.
📲 Buying via app is always cheaper than on the website!
❱❱ Install the AutoDoc App - interstitials.onelink.me/1036...
🛒 On our website you will find a wide range of auto parts you are interested in: www.autodoc.co.uk/?...
Springs: www.autodoc.co.uk/car-parts/c...
Springs for PEUGEOT 208 1: www.autodoc.co.uk/car-parts/c...
Shock absorber: www.autodoc.co.uk/car-parts/s...
Shock absorber for PEUGEOT 208 1: www.autodoc.co.uk/car-parts/s...
Strut mount: www.autodoc.co.uk/car-parts/s...
Strut mount for PEUGEOT 208 1: www.autodoc.co.uk/car-parts/s...
LIQUI MOLY Chain Spray: www.autodoc.co.uk/liqui-moly/...
WD-40 Grease Spray: www.autodoc.co.uk/wd-40/13563...
🔔 Subscribe to AUTODOC's channel and don't miss new videos on car parts replacement ➜ ru-vid.com?s...
🛠️ The tools you need to replace a front shock strut:
- wire brush
- WD-40 spray
- copper grease
- HEX bit No.H7
- combination spanner No.19
- drive socket No.E8
- drive socket No.16
- drive socket No.18
- drive socket No.21
- drive socket No.32
- wheel impact socket №17
- shock absorber socket
- ratchet wrench
- torque wrench
- pin punch
- hammer
- tap wrench
- rubber mallet
- crow bar
- hydraulic strut spring compressor
- hydraulic transmission jack
- fender cover
- wheel chock
Was this video helpful? Give it a thumbs-up and share it with your friends!
Have a look at other videos on our channel:
► PEUGEOT car repair tutorial - • PEUGEOT car repair tut...
► PEUGEOT 208 1 car repair tutorial - • PEUGEOT 208 (CA_,CC_) ...
► How to replace front anti roll bar link / front drop link on PEUGEOT 208 1 (CA_,CC_) - • How to change front an...
► How to replace front brake discs / front brake rotors on PEUGEOT 208 1 (CA_,CC_) - • How to change front br...
Mobile Shop: m.autodoc.co.uk
📢 AUTODOC in social media:
Facebook: / autodoc.co.uk
Twitter: / autodoc_berlin
RU-vid: / autodocuk
Instagram: / autodoc_autoparts
#autodoc #autodoctutorial
Disclaimer:
This video is intended for informational purposes only and does not guarantee achievement of a specific result.
It is recommended that you entrust the installation to highly skilled technicians to ensure the best result.
This video only contains tips and recommendations that could be helpful when carrying out car repairs or replacing parts. AUTODOC is not liable for any harm, injury or property damage incurred while carrying out repairs or replacements, that are a result of incorrect use or misinterpretation of the provided information. This video is for informational purposes only and does not guarantee achievement of a specific result. The user is personally liable for incorrect use of repair equipment, tools or car parts, in particular, when this use poses the risk of injury. AUTODOC strongly recommends being careful and adhering to the safety rules when doing any repair or replacement. Keep in mind that using low quality auto parts does not guarantee the proper level of road safety.
© 2019 AUTODOC GmbH All rights reserved

Авто/Мото

Опубликовано:

 

25 июл 2019

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 29   
@autodocuk
@autodocuk 6 месяцев назад
Attention! This video contains mistakes: 9:09 - the tightening torque is 55 Nm, not 105 Nm. 9:15 - the tightening torque is 40 Nm, not 65 Nm. 9:20 - the tightening torque is 43 Nm, not 55 Nm. 10:10 - the tightening torque is 60 Nm, not 50 Nm. 10:34 - the tightening torque is 245 Nm, not 115 Nm. 10:46 - the tightening torque is 100 Nm, not 110 Nm. We're sorry for the inconvenience 🙇‍♂
@autodocuk
@autodocuk 5 лет назад
Have a look at other videos on our channel: 🔸 PEUGEOT 208 1 car repair tutorial - ru-vid.com/group/PLWep5LzT0sxnLT8M6UaR2DSD7Cm4ZlS4T 🔸 How to replace front suspension arm PEUGEOT 208 1 (CA_,CC_) - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-fGnIPzW3_jc.html 🔸 How to replace pollen filter / cabin filter on PEUGEOT 208 1 (CA_,CC_) - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-CdBzOXHnvWA.html 🔸 How to replace spark plug on PEUGEOT 208 1 (CA_,CC_) - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-nexOMEFaDbQ.html 🔸 How to replace front brake discs / front brake rotors on PEUGEOT 208 1 (CA_,CC_) - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Y_GfdQNbs-s.html
@SuperScalextric
@SuperScalextric 3 года назад
Great tutorial but bear in mind these additional points. These springs are side-loaded and are difficult to reinstall even with a workshop compressor. Study the positioning of everything in the video closely before attempting. Note the socket used to lever the strut base forward. This is critical but not mentioned in the video - however it is just about visible. I used this video for a 2008. The driveshaft nut is 35mm (not 34mm, not 36mm) and requires 325Nm (240 lbs ft) to secure
@autodocuk
@autodocuk 3 года назад
Thank you for sharing your experience, it will be very useful information for us and our viewers. Best Regards, Autodoc team
@jameselder3476
@jameselder3476 Год назад
11 minutes. Seems easy. 🎉
@AymenMusnic
@AymenMusnic 3 года назад
I did enjoy it, thanks for the tutorial ❤❤
@Bertamirans255
@Bertamirans255 5 лет назад
Thanks
@kenrossaukrsa
@kenrossaukrsa Год назад
Can you adjust the camber with the pinch bolt at the bottom of the shock?
@alexey9900
@alexey9900 5 лет назад
Good 👍👍👍
@richbehague2480
@richbehague2480 5 лет назад
Good video, just a pointer, you didn't stake down the hub nut on reassembly. Hopefully a new nut was used as well?
@autodocuk
@autodocuk 5 лет назад
Thank you for your comment! You are absolutely correct, we had to skip this step to reduce the length of the video. The new nut was used as well, behind the scenes. Best Regards, Autodoc Team.
@tonvel1964
@tonvel1964 2 года назад
is it the same procedure on the Peugeot 2008 ?
@autodocuk
@autodocuk 2 года назад
In general, the replacement will be similar, the only thing that may be slightly different is the design features of your car. You can find more detailed information in the technical documentation for the repair of your car. AUTODOC
@jt6945
@jt6945 5 месяцев назад
Can you confirm which way the small notch cut out in the top mount faces please.. outwards. Or inwards towards the engine? Thx
@Slowmotors123
@Slowmotors123 5 месяцев назад
Faces in towards engine
@jt6945
@jt6945 5 месяцев назад
@@Slowmotors123 I though so. Thank you
@mattsky0794
@mattsky0794 6 месяцев назад
Good info, that music was bloody awful though
@drywipe1989
@drywipe1989 4 года назад
Can I get away with not undoing the hub nut?
@autodocuk
@autodocuk 4 года назад
Thank you for your comment! You do not have to remove the central bolt of the hub, but this is fraught with the fact that when you dismantle the shock absorber, you will pull the driveshaft and pull it out of the gearbox, after which oil will surely flow out of the gearbox. Changing the oil in the box is not a cheap procedure, and it's easier to protect yourself and remove the hub bolt. Best Regards, Autodoc team
@drywipe1989
@drywipe1989 4 года назад
@@autodocuk thank for your response! Wish I'd seen this before, guess who has dumped gearbox oil over their drive haha
@JamesSmith-tv3pz
@JamesSmith-tv3pz 14 дней назад
Kill this awful background dross 'music' otherwise an excellent and informative video 👌
@onurguzel16
@onurguzel16 3 года назад
I was looking for the other side. The grill doesn't come off on the other side.
@RCS163
@RCS163 3 года назад
Im having this exact issue right now. Found a solution yet?
@onurguzel16
@onurguzel16 3 года назад
@@RCS163 Nope but what I heard is that the whole grill has to be pulled off completely to reach and clean the other side. What a drama :(
@Huseyin1422
@Huseyin1422 2 года назад
Onur hocam donanım haber dışında seni burada görmek ne güzel :D Sıkıntı mı vardı süspansiyonlarda
@onurguzel16
@onurguzel16 2 года назад
@@Huseyin1422 Hocam selamlar :) Sizin DH nicki neydi? Valla bir ara garç gurç sesleri vardı, bu aralar yok, kafasına göre bazen olabiliyor :)
@TheFuzzy0ne
@TheFuzzy0ne Год назад
Please could somone explain what purpose the pin punch serves at 3:17?
Далее
БАТЯ И ТЁЩА😂#shorts
00:58
Просмотров 2,4 млн
80 Year Olds Share Advice for Younger Self
12:22
Просмотров 1,4 млн
Most Common Strut Installation Mistakes!
14:02
Просмотров 1,1 млн
How to replace the control arms Peugeot 208 mk1 🚗
6:48
ВЫХЛОП НА ЯПОНЦА TWIN LOOP #shorts
0:52