No video :(

How to change front suspension arm / front control arm on RENAULT MEGANE 2 (LM) [TUTORIAL AUTODOC]

autodoc.co.uk

Подписаться 395 тыс.

Просмотров 46 тыс.

50% 1

How to change front suspension arm / front control arm on RENAULT MEGANE 2 (LM) 1.4 Saloon 09.2003-present [TUTORIAL AUTODOC]
Suspension arm on RENAULT Captur (06.2013-2019) / RENAULT Grand Scénic II (JM) (04.2004-2011) / RENAULT Megane II Sport Tourer (KM) (08.2003-01.2011) / RENAULT Scénic II (JM) (06.2003-2011) / RENAULT Scénic III (JZ) (02.2009-2014) cars should be replaced, as a rule, according to one and the same procedure.
However, there can be slight differences due to specific features of the vehicle design.
🔝 Top brands that produce suspension arm: RIDEX; VAICO; STARK; TOPRAN; A.B.S.
📲 Buying via app is always cheaper than on the website!
❱❱ Install the AutoDoc App - interstitials....
🛒 On our website you will find a wide range of auto parts you are interested in: www.autodoc.co...
Suspension arm: www.autodoc.co...
Suspension arm for RENAULT MEGANE 2: www.autodoc.co...
LIQUI MOLY Chain Spray: www.autodoc.co...
WD-40 Grease Spray: www.autodoc.co...
🔔 Subscribe to AUTODOC's channel and don't miss new videos on car parts replacement ➜ www.youtube.co...
🛠️The tools you need to replace front suspension arm:
- wire brush
- WD-40 spray
- copper grease
- combination spanner no. 16
- combination spanner no. 18
- drive socket no. 12
- drive socket no. 13
- drive socket no. 16
- drive socket no. E16
- drive socket no. 18
- Torx # T20
- wheel impact socket no.19
- shock absorber socket
- ratchet wrench
- torque wrench
- clip removal tool
- pin punch
- hammer
- crow bar
- rubber mallet
- hydraulic transmission jack
- fender cover
- wheel chock
Was this video helpful? Give it a thumbs-up and share it with your friends!
Have a look at other videos on our channel:
► RENAULT car repair tutorial - • RENAULT car repair tut...
► RENAULT MEGANE 2 car repair tutorial - • RENAULT MEGANE 2 car r...
► How to change a front brake discs and front brake pads on RENAULT MEGANE 2 - • How to change a front ...
► How to change a Silencer holding bracket RENAULT MEGANE 2 - • How to change a Silenc...
Mobile Shop: m.autodoc.co.uk
📢 AUTODOC in social media:
Facebook: / autodoc.co.uk
Twitter: / autodoc_berlin
RU-vid: / autodocuk
Instagram: / autodoc_autoparts
#autodoc #autodoctutorial
Disclaimer:
This video only contains tips and recommendations that could be helpful when carrying out car repairs or replacing parts. AUTODOC is not liable for any harm, injury or property damage incurred while carrying out repairs or replacements, that are a result of incorrect use or misinterpretation of the provided information. This video is for informational purposes only and does not guarantee achievement of a specific result. The user is personally liable for incorrect use of repair equipment, tools or car parts, in particular, when this use poses the risk of injury. AUTODOC strongly recommends being careful and adhering to the safety rules when doing any repair or replacement. Keep in mind that using low quality auto parts does not guarantee the proper level of road safety.
⚡ AUTODOC CLUB - club.autodoc.c...
Add your car to the AUTODOC CLUB garage and get personal recommendations on repair intervals - club.autodoc.c...
❱❱ Install the AUTODOC CLUB App - club.onelink.m...

Опубликовано:

10 апр 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 34

@autodocuk Год назад

Attention! This video contains mistakes: 8:03 - the tightening torque is 105 Nm, not 95 Nm. 8:09 - the tightening torque is 105 Nm, not 90 Nm. 8:20 - the tightening torque is 62 Nm, not 70 Nm. We're sorry for the inconvenience 🙇‍♂

@autodocuk 5 лет назад

Have a look at other videos on our channel: 🔸 RENAULT MEGANE 2 car repair tutorial - ru-vid.com/group/PLWep5LzT0sxn6nG18knxG4k4To6CEFmhi 🔸 How to replace fuel filter RENAULT MEGANE 2 - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-m_nW6xjpWDk.html 🔸 How to replace front anti roll bar link / front drop link on RENAULT MEGANE 2 - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-u4kkD2giXX8.html 🔸 How to replace air filter on RENAULT MEGANE 2 - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-VvGtvzup14g.html 🔸 How to replace pollen filter / cabin filter on RENAULT MEGANE 2 - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Z1VMu3GAWYY.html

@michaelgolf6941 Год назад

Brilliant, informative with clear in-depth instructions. Well done.

@autodocuk Год назад

We are glad that you enjoy our work!

@democracyforall 5 лет назад

Even though you do not have big views for now but, your videos are the best so far.

@autodocuk 5 лет назад

Thank you for your support! The best is yet to come. Stay tuned for more! Best regards, Autodoc.

@gaspuu 5 лет назад

@@autodocuk If you keep doing this and increase your portfolio of car repairs vids, it'll be legendary soon. I'm big fan and crossing fingers because I think you are doing something remarkable......just don't overdo it with pricing of the parts you offer :)

@jonnijames 5 лет назад

@@autodocuk Olivers right, great quality, especially telling us all the tools used, i cant work out why your using a transmassion jack on the front radiator part though, wouldnt it hold by dangling there for a while?

@Kieran46100 2 года назад

excellent video, thanks a million for sharing

@autodocuk 2 года назад

Hi! Thanks for the feedback, we're trying to make the best videos for you.

@crigeorge9549 3 года назад

4:50. there goes the gearbox oil. 8:20 70 NM torque setting? That bolt won't witstand the factory 62nm setting. That's a common sense tightening screw. Bolt threads will be shaved of at 70NM. Also he used 90 NM for the other 2 arm bolts. The manual says 70 NM. The factory setting for the 2 big bolts under the radiator frame is 105NM not 70NM. You tighten the ball joint screw to 70 wich is thiner. 10:03 this how they ruin the protective under the engine plate nuts. Buddy those screws are to be tighten to 21 NM. That pneumatic pistol shaves the frame nuts threads. Same thing to the side plates same torque stiing yet he used the same pistol. Short say. The video doesn't match the reality. 4:17...you got to be kiding. years will pass untill you take out that screw with that pin punch hamering thing and craw bar on some cars that rust welded them together.This also happens with the shock absorber botom. I remember 1 time I broke the screw head trying to slaken and undo the screw. On many cars it will be so rusted that will take hours with diferent technics to take the screw and the ball joint out. And admitedly Renault are cunts when it comes to designing mechanics. Half the car dismantled just for a part to take out like the suspension arm.On my 1.9 dci front bumper removed, otherwise the radiator underneath frame wouldnt slide of because of a bigger engine. This one is 1.5 dci I think. They were made so you take a visit to the garage quite often. Look at hat rear arm bush. The way it works you can tell it won't last long. They couldn't use the same bush as the front type bush . The only thing good about it is that the arm is single layer and you can easily replace the bushes and ball joint individualy.

@jdickson242 5 лет назад

Renault sure know how to over complicate a simple job. I also like how every bolt is a standard nut and bolt oh know sorry one bolt it randomly a star bolt....why renault why?!?!

@freddytait7726 11 месяцев назад

Tie rod end. Replacement Not shown. ????

@jonnijames 5 лет назад

Top video mate, May i ask at 5:30 he has the front left K frame split into two, the video doesnt show much reason as to why that part is split in the middle, can you elaborate more on this, it seems a missing piece to me, thanks in advance .

@autodocuk 5 лет назад

Thank you for your request! Unfortunately, each vehicle is unique, it all depends on the technical condition of the parts. Our videos are for informational purposes only and aim to show the replacement sequence and to save time, we miss some obvious points. However, we appreciate your comment and will make sure to cover more details of replacments in our new videos. Best Regards, Autodoc Team.

@camby1uk 5 лет назад

I think the reason is the front arm bolt doesn't fit out so you cant get the arm off.

@jonnijames 3 года назад

@ferkemall cheers, sounds like fun, LOL

@larszettergren4752 3 года назад

What tool is the special drive socket to widen the steering knuckle

@autodocuk 3 года назад

Please clarify or rephrase your question. AUTODOC

@larszettergren4752 3 года назад

5.24 minutes in the video there I some kind of drive socket left in the picture. Guess it is used to video the grove in steering knuckle.

@competiti22 3 года назад

could be wrong but not sure its a special tool, looks to me like and old something they dont want anymore they are forcing into it to pry it open. The normal tool you use to get the ball joint of however is a ball joint splitter.

@gabrielmiron6299 Год назад

Hi , can you please tell me what is the name of the part , the steel plate he is taking off at 02:20 ? I replaced the ball joint arms on my Megane two , and the part I am talking about was rusted to the point where it had no structural integrity and I don't know the name of it to order a new one.

@autodocuk Год назад

This is the front subframe booster.

@alexey9900 5 лет назад

👍👍👍SUPER

@autodocuk 5 лет назад

Thank you for the feedback! Stay tuned. Best regards, Autodoc.

@BarrattDigital Год назад

Oof, that's a lot of work. Not sure I'll be able to make this a job I can do on my drive way but can't really afford a garage to do it right now :(

@abdelkadernaceri6155 4 года назад

Hard work. Nonsense conception.

@samimahealthcare7304 5 лет назад

Want engine overholing tutorial Keep my request next tutorial want it.

@autodocuk 5 лет назад

Thank you for the feedback! We strongly recommend to do engine overhauling only in the specialized car service centers. Best regards, Autodoc.

@RS-gd2ct Год назад

What a huge piece of junk this car is... Feel bad for the owners

@truckerdude4813 5 лет назад

Another reason not to buy a Renault!

@andyhollis502 5 лет назад

im sure every make of car has suspension that needs changing once worn.. my meganes done 155k and still pulls like a train .. had a lot of front suspension work done and im sure any car thats got 150k has had the same

@jdickson242 5 лет назад

These videos help a lot I have a ford 2006 fiesta and a 2011 estate clio. I am literally stunned how complicated renault make simple tasks. Loosening the radiator sub frame just to access one bolt. Nice one and crazy. I replaced the radiator on the clio last year. Looked like i was replacing the whole front end. Lol