Тёмный

How to clean drive by wire Throttle Body on most KIA Vehicle 

Wrenching Ryan
Подписаться 4,5 тыс.
Просмотров 55 тыс.
50% 1

You can clean drive by wire throttle body without opening the butterfly valve with the proper cleaning brush. This vehicle experience poor idle and sometimes stalling, I recommend throttle body cleaning and here are the step by step process. NOTE: opening the butterfly valve without unplugging the connector sometimes required calibration.
#kia #throttlebody #cleaning #howto

Авто/Мото

Опубликовано:

 

24 окт 2022

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 110   
@pmpbuhgm
@pmpbuhgm Год назад
Highly appreciate your time and effort to create such an informative and helpful content you are the best.
@WrenchingRyan
@WrenchingRyan Год назад
Thank You so much 🙏
@igorr1402
@igorr1402 Год назад
Thank you very much for your video, very easy to follow. Close views allowed me to understand in details the steps. However I had a bit of panick right after cleaning the throttle body. First time I tried to start the engine it ran for 2 seconds, then stopped. Next try 1 second. Next try did not run at all. I found on forums that it is indeed pretty common when cleaning the throttle body. According to the forum, a trick that often works is to floor it and release the pedal once the engine runs. I did it and it worked. Maybe an improvment for your videos could be a "frequently encountered problem" section at the end. (for dummies like me not to panick 😂)
@WrenchingRyan
@WrenchingRyan Год назад
Mostly after throttle cleaning your engine will experience long crank/rough idle for few seconds. Loved the idea about frequently encountered problems after cleaning. For sure will be added on my next video. Thank you 🙏
@user-cn9sg6nz7i
@user-cn9sg6nz7i 8 месяцев назад
Very useful tip thanks
@WrenchingRyan
@WrenchingRyan 8 месяцев назад
you’re welcome. thanks for watching.
@romanc.5074
@romanc.5074 Год назад
Thanks.
@WrenchingRyan
@WrenchingRyan Год назад
You're welcome
@juliangallegos7627
@juliangallegos7627 9 месяцев назад
Good Morning! I am having issues with my wife's 2017 Kia Rio LX so I decided to post on here for any suggestions or helpful tips! I am no mechanic however I did a ton of research in hopes to get this problem resolved! Here is the story so far.... 2017 Kia Rio LX V4 Error Code: P0445 fixed P0442 active Problem: Stalls at Idle/stop signs after driving for 30+ Once turned off it can take 2-5 minutes of rest until the car successful turns back on Replaced: Canister Close Valve Purge Valve Gas Cap Crankshaft Sensor Hypothesis / Things not yet replaced or tested: EVAP Vacuum Leak or Clog Vent Solenoid Charcoal Canister Cracked/ Defective Thank you in advance! 2017 Kia Rio LX 1.6 L 4-cylinder
@WrenchingRyan
@WrenchingRyan 9 месяцев назад
Start the engine and let it stall, if you have fuel pressure gauge check for pressure it should be 50 to 70 psi, if pressure is low culprit might be the fuel pump. Seems like PCSV already replace, check PCSV pin tension if pin tension is good suspect possibly short to ground in control circuit. Good luck.
@juliangallegos7627
@juliangallegos7627 9 месяцев назад
@@WrenchingRyan thank you so much for your service- I truly appreciate the expert information!!
@cristiantules8301
@cristiantules8301 Год назад
Great video! Can you tell why you clean that black circle on the back side? I belive that is a factory thing!
@annaboyle4896
@annaboyle4896 22 дня назад
The black ring is most likely carbon deposits that's causing the rough idle. If it is something that comes from factory I would look into it to see if its something that needs to be cleaned or shouldn't be but normally factory ones are completely bare metal.
@bringforthtruth
@bringforthtruth 7 месяцев назад
Do you have to replace the gasket? I saw a orange one on the engine.
@WrenchingRyan
@WrenchingRyan 7 месяцев назад
check the gasket condition, 9 out of 10 you can re used it but if gasket is in bad shape replace it. thanks for watching
@CollinsH86010
@CollinsH86010 Год назад
What’s the socket size to unscrew the bolt?
@WrenchingRyan
@WrenchingRyan Год назад
10mm bud, thanks for watching.
@nelsonchook
@nelsonchook 10 месяцев назад
FOR KIA FORTE 2012 ALSO SAME?
@WrenchingRyan
@WrenchingRyan 10 месяцев назад
For the most part yes. thanks for watching.
@bobdublin825
@bobdublin825 Год назад
Did you put a new gasket on after cleaning
@bringforthtruth
@bringforthtruth 7 месяцев назад
I would ask this too.
@JadeNecromancer
@JadeNecromancer 5 месяцев назад
Hi I saw your video, wondering if the issue is the same. As my RPM will dip to around 500rpm and engine vibration is quite significant when I switch my aircon speed to fan 2. When I am on aircon speed fan 3 no issue engine not much vibration. Can this be fix by cleaning the throttle body? Driving a kia k3 (2013)
@WrenchingRyan
@WrenchingRyan 5 месяцев назад
when the A/C compressor is on basically your adding more load to the engine then RPM will slightly change, you can clean your throttle plate using this simple step, if the issue still exist start checking your engine mount, Kia release service bulletin few years ago for Kia forte excessive vibration when a/c is on, we replaced alternator pulley to fix the concerned. good luck and thanks for watching.
@Woodygdmax
@Woodygdmax 10 месяцев назад
I have a 2020 kia telluride is this applicable?
@WrenchingRyan
@WrenchingRyan 10 месяцев назад
Two different engine but for the most part yes. Watch this link to get idea ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-CCe-ltGQJQg.htmlsi=wucAJF8BqW3l6r7X
@taylorsharp212
@taylorsharp212 2 месяца назад
Ive got a 2006 kia rio and its is sluggish on acceleration it idles rough. And even worse when the ac is turned on ive got no engine codes and nothing major going on. Do you think this may help my issues with the sluggish acceleration in stop and go traffic.
@taylorsharp212
@taylorsharp212 2 месяца назад
Also what are you using. Surly not break cleaner yeah?
@WrenchingRyan
@WrenchingRyan 2 месяца назад
@@taylorsharp212 I’ve fixed so many idle issue by cleaning the throttle plate, it’s not gonna hurt if you give it a try. I’m using BG Throttle Body & Intake Cleaner.
@walrus-king
@walrus-king 6 дней назад
In my experience that sounds like a failed cat, things never wanna throw a code on Kia’s.
@trippyextendo8387
@trippyextendo8387 Год назад
what product did you use
@WrenchingRyan
@WrenchingRyan Год назад
BG product, look it up good stuff for your engine.
@ozyl8069
@ozyl8069 Год назад
It is not easier to remove it completely and clean it?
@user-xi1to4ph6s
@user-xi1to4ph6s Год назад
How often should be done? I have 2016 KIA Forte. Is there a need to disconnect the negative terminal of the battery?
@WrenchingRyan
@WrenchingRyan Год назад
I personally recommend to clean it every 30k miles, you are welcome to disconnect neg. Battery cable, disconnecting throttle body connector might need programming, most kia don’t. Just follow this steps and you will be fine. Thanks for watching.
@kokryan4549
@kokryan4549 Год назад
After cleaning need to reset anything?
@WrenchingRyan
@WrenchingRyan Год назад
Perform this steps and no program needed. Thanks for watching.
@Itsolivera
@Itsolivera 3 месяца назад
What is the relearning process for a 13 optima 2.4 ? If I clean do I even have to relearn ?
@WrenchingRyan
@WrenchingRyan 3 месяца назад
If you clean it the way I did no relearning required, if you decided to disconnect the connector and clean it relearn MIGHT required, by the way scanner is required for relearning process. Thanks for watching.
@Itsolivera
@Itsolivera 3 месяца назад
Ok cool, thanks! So scanner is needed to reset and relearn? Great thanks for the info @@WrenchingRyan
@WrenchingRyan
@WrenchingRyan 3 месяца назад
@@Itsolivera Yes scanner is needed to perform reset/relearn.
@gmm1904
@gmm1904 5 месяцев назад
Don’t need calibration like in nissan ?
@WrenchingRyan
@WrenchingRyan 5 месяцев назад
If you follow exactly how I did it no calibration needed, but if you unplug the connector and open the plate calibration might required. Thanks for watching.
@DAK59
@DAK59 29 дней назад
I use a toothbrush. It's smaller and gets in the throttle body easier.
@WrenchingRyan
@WrenchingRyan 28 дней назад
Anything works right.. Thanks for watching.
@moinshek
@moinshek 11 месяцев назад
No need to disconnect battery ?
@WrenchingRyan
@WrenchingRyan 11 месяцев назад
I don’t know why disconnecting the negative battery cable did know appear in the video. Please disconnect the negative battery cable before performing this job. Thanks 🙏
@petegurdal1844
@petegurdal1844 8 дней назад
Just that little dirt makes a big deal in car running smoothly?
@WrenchingRyan
@WrenchingRyan 8 дней назад
Yup, I had one not long ago doesn’t wanna stay idle no code, so i started cleaning the throttle plate and engine runs/idle smoothly.
@kennedypeele5913
@kennedypeele5913 Год назад
Hi, could cleaning this fix code P0507?
@braverinchrist5973
@braverinchrist5973 Год назад
Should blow out debris after covering intake
@WrenchingRyan
@WrenchingRyan Год назад
I did blow all debris out before I return vehicle to customer. Thanks for watching.
@cumshot247
@cumshot247 7 месяцев назад
Should blow out debris BEFORE removing anything...
@grimfandangox
@grimfandangox 3 месяца назад
Why didn't you take it out? did you just clean inside the car?
@WrenchingRyan
@WrenchingRyan 3 месяца назад
yeah, I just cleaned it inside the car, this throttle body is drive by wire, you can remove it and clean it but there’s possibility of programming needed after cleaning.
@grimfandangox
@grimfandangox 3 месяца назад
@@WrenchingRyanDoes this throttle require adaptation? I thought it did it automatically.
@WrenchingRyan
@WrenchingRyan 3 месяца назад
@@grimfandangox if you do it exactly how I did it no relearning needed. If you disconnect the throttle body connector and open the plate you might need to do relearning.
@markovalenzuela3315
@markovalenzuela3315 4 месяца назад
how can you do the relearn without a scanner?
@WrenchingRyan
@WrenchingRyan 4 месяца назад
scanner is required to perform relearn but you can try this, remove negative and positive battery cable, touch them together for 3 to 5 minutes. hope this work.
@LanceB86
@LanceB86 3 месяца назад
There's no way you just pulled that thing up out of there without disconnecting something else... I'm trying to pull mine out to get to the backside, but it seems impossible without disconnecting either the radiator hose or some of the wiring harnesses...
@WrenchingRyan
@WrenchingRyan 3 месяца назад
You can disconnect the throttle body assembly and clean it thoroughly, I did it this way to avoid possible re programming, this throttle body is driven by wire if you open the plate re programming MIGHT needed. FYI I’ve clean a lot by putting them out but one time I got some idle issue and only way to fix it is relearning it.
@beterbey
@beterbey 10 месяцев назад
If you move that butterfly valve as you clean it, it's totally screwed up and no way to repair / reset. Not a cheap part either..
@WrenchingRyan
@WrenchingRyan 10 месяцев назад
💯% agreed 👍
@WanderingHewitts
@WanderingHewitts 9 месяцев назад
Never heard this before. I moved the butterfly when cleaning it and it didn't seem to have any negative effects. I've driven it for probably 100 miles so far and it seems fine. Fingers crossed.....
@beterbey
@beterbey 9 месяцев назад
@@WanderingHewitts If it's an old style cable controlled butterfly valve, no problem. But if it's an electronic controlled one, you should not change valve angle as you clean it. No way to repair, no way to recalibrate, you got to replace it with a new one..
@WanderingHewitts
@WanderingHewitts 9 месяцев назад
@@beterbey it's the electronic one but the car idles and runs perfect. I did disconnect the battery beforehand and it's not throwing any check engine lights. Maybe I got lucky
@cumshot247
@cumshot247 7 месяцев назад
Was told if you disconnect battery, it won't affect it as long as you don't aggressively open & close, or let it slam shut.
@herbertlisone9047
@herbertlisone9047 Год назад
the real question is, where do you buy that brush from?lol
@danpaytas9662
@danpaytas9662 11 месяцев назад
Dollar tree !
@justinkashtock333
@justinkashtock333 4 месяца назад
Harbor Freight has them.
@DAK59
@DAK59 4 месяца назад
Use a toothbrush. It's smaller and fits better.
@DRDROP-fj4bo
@DRDROP-fj4bo Год назад
My 2.4 shudders at red light with brake on and in gear. Cleaned throttle body twice. No improvement. Only does it once it warms up. Thinking i need a GDI service. No telling what the valves look like.
@WrenchingRyan
@WrenchingRyan Год назад
GDI service is not bad idea, before you do that take your vehicle to auto store and have them scan it for free, PCM might store a code to begin with. Also you can check your spark plugs for cracks, worn out engine mounts. Good luck.
@DRDROP-fj4bo
@DRDROP-fj4bo Год назад
@@WrenchingRyan Thanks for reply. Yeah I got a good scanner. Only code i get is very small evap leak occasionally when it runs system check. Performed a smoke test and no leaks under the hood. Tested canister purge valve solenoid and it good.Tested coils every way I can and they check out. Going to replace they got lot of miles on them. Maybe one breaking down when it gets hot.
@jeffreymeyer8950
@jeffreymeyer8950 Год назад
​@@WrenchingRyan Isn't a gdi service just spraying the throttle bottle cleaner directly into intake while car is running at 2k rpms?
@meaux444
@meaux444 Год назад
I want to try this.. and you're literally explaining all of the symptoms with my '15 Soul; super high mileage.
@charleslambertjr3842
@charleslambertjr3842 Год назад
No need to replace the seal / O-ring I’m guessing / if it was needed, you would’ve shown it getting replaced, correct?
@miltinhogooglejr8620
@miltinhogooglejr8620 10 месяцев назад
I have a 2015 Kia Forte LX with 385,000 miles on it, and I´ve only cleaned the throttle 3 times now. I know! Shame on me!
@WrenchingRyan
@WrenchingRyan 10 месяцев назад
Wow… 360,000 mile in it just amazing. I’ve been in Kia dealership and the most Kia engine miles I dealt with is 240,000 mile.
@miltinhogooglejr8620
@miltinhogooglejr8620 10 месяцев назад
I had to go back to my local Kia Dealership to have the ignition recall taken care of, and they were shocked when they saw my mileage. Thank God I have been blessed with a very good car. @@WrenchingRyan
@M_DWHITFIELD
@M_DWHITFIELD 6 месяцев назад
I have a 09 kia 3.3 sorento with 302 ,000 and a 07 kia 3.5 sorento with 281,000 on it there good motors if taken care of
@justinkashtock333
@justinkashtock333 4 месяца назад
Even taken care of, our 2010 2.4 eats a fair amount of oil at 165k; some people just have better luck or live in areas without a lot of stop and go traffic.
@roger8772
@roger8772 Месяц назад
WOW! i hope my 2016 Forte gets 380,000 🙏 is it still the original trans?
@stevenweiss2148
@stevenweiss2148 9 месяцев назад
He thinks he is sanitizing his toilet. Not necessary!
@WrenchingRyan
@WrenchingRyan 9 месяцев назад
😂
Далее
How to Clean an Electronic Throttle Body Safely
4:36
SYMPTOMS OF BAD THROTTLE BODY ON HYUNDAI KIA
5:18
Просмотров 37 тыс.
2013 Kia Optima Brake Lights Stay On Fix
5:39