Pioneer in-dash receivers are designed to hold the clock and radio station settings after you leave your vehicle. You may have your receiver wired incorrectly. If your clock and radio stations reset each time you start your vehicle, the in-dash receiver may have an improper connection for the Yellow Wire. The Yellow Wire must have constant power from the vehicle. This means if the vehicle is switched on or switched off, the yellow wire should measure at ~12 volts. The Red Wire is for accessory. You can view the red wire as the receiver’s on/off switch. The red wire should measure ~ 12 volts only when the vehicle is switched on. ---Do not connect the Red Wire and Yellow Wire together. --- Please take a look at this video for more information on wiring your Pioneer in-dash receiver: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-kR2MO2kwFug.html You can find more videos on Pioneer's RU-vid Channel here: ru-vid.com
@pioneerelectronics How do I use a amp with the cdplayer? I am trying to power my highs. All I get is bass...... I cannot find how to adjust preout like it says in the manual.
On mine you can hear it but you can barely hear the vocals. I tried to adjust the audio settings but it didn't make a difference All the wiring is right, it happened when I replaced my car battery. Any suggestions?
The Pioneer DEH-150MP has one set of RCA outputs for operating an external amplifier. This limits some of it's capabilities. It's certainly possible to add more than one amplifier to this receiver. However, the control from the in-dash receiver, over the amplifiers and connected speakers will be very limited. It can be done by splitting the RCA signal to more than one amplifier, or by using an amplifier that has RCA outputs as well as RCA inputs. There are other options as well to create additional ways to add a second amplifier. Please consider a Pioneer 4 channel amplifier like the GM-D8704 seen here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-E-VbUBAGwAI.html If you are wanting to add an amplifier for good sound quality and loud and clear audio, it may be time to consider a new in-dash receiver that has more than one set of RCA outputs. With two or three sets of RCA outputs you have more control over the system from the receiver. Please consider the Pioneer MVH-S320BT seen here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-cXbvdfgLS2o.html or the Pioneer DEH-S7200BHS seen here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-_mwzEMGuhbU.html You can find more videos on Pioneer's RU-vid Channel here: ru-vid.com
I recommend to use the Fader and Balance Control shown in the video here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-WKPVQMgc6nI.html The Fader moves the sound from front to rear. Set the Fader Control to Center. The Balance Control moves the sound from right to left. Set the Balance Control to Center. If this does not correct the issue, it's possible the speakers that are not working have failed and need to be replaced, or the speakers that are not working are not properly connected to the in-dash receiver. You can learn more about wiring your Pioneer in-dash receiver here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-kR2MO2kwFug.html You can learn more about Pioneer Speakers here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-MgZzTIqBBa8.html and you can find more videos on Pioneer's RU-vid Channel here: ru-vid.com
Hey there, good vids as always. Listen i have 2 pioneer steroes on the back and 2 small on the front, along with a mvh s100ub stereo. I cnat manage to set the right equilizer settings. What settings would you recommend please? Also includings hpf etc. :d it would be a very big helppp thankss
Try this and make adjustments as needed. I recommend setting the HPF at 63Hz. If you have a subwoofer, set the LPF for 80Hz. If not, turn the subwoofer off. Set the EQ to the powerful setting. Turn off Loudness.
I just had this system installed and have a question. As far as the scrolling on the screen, is there a way i can get the radio station and song to display? And how would i do that if possible
Hi! Do you know how I can increase the volume on AUX source? My AUX source has a lower volume comparing with the USB or RADIO source and it's annoying.
Please be sure to raise the volume on your music player you are using for AUX playback. Change the Pioneer DEH-150MP to the AUX source. When on the AUX Source, Press in on the volume control and turn to the Audio menu. From the Audio menu, Press in on the volume control and turn to SLA. SLA is Source Level Adjuster. This setting can add more volume to the AUX source as compared to radio. The SLA setting works on USB and CD, and AUX. SLA does not appear in the Audio Menu when on the Radio source. You can find more videos about Pioneer DEH-150MP here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yMXSLfhG18A.html and here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ywuLd0oQ_UI.html You can find more videos on Pioneer's You Tube Channel here: ru-vid.com
I let my mom take my car one day and the radio channels came back all messed up and I had nothing but some random jazz stations but I got it back to normal. Only issue is now my aux no longer works. The cord is fine but the radio won't switch from radio stations to aux. can someone help
is there a setting for turn on volume so if your music is loud when you turn off the car and when you get back and turn on your car it will be lower or whatever you set it too
My radio dont work like it used to, when I wanna play a song on it from my phone(via cables) it shows up AMP ERROR. And I have to restart and reconnect all of it… what is the problem??
When AMP ERROR is displayed on your Pioneer receiver, it may mean the receivers speaker wires are touching one another. I recommend to check the back of the receiver for any exposed wires that may be touching one another or metal in the vehicle. You can learn more about wiring your Pioneer receiver here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-kR2MO2kwFug.html I suspect that when you push the AUX input cable into the receiver, you are pushing the receiver back just enough to cause two speaker wires to touch one another. This causes the AMP Error. In addition, check the speaker locations, in the doors, or rear deck or other areas to be sure that no speaker terminal is touching metal in the vehicle. You can find more videos on Pioneer’s RU-vid Channel here: ru-vid.com
the bass is so goddamn powerful on this radio like it’s super overwhelming and you can barely hear the song, please help? clear instructions please i don’t know how to work any of this lmfao
What model number of Pioneer in-dash receiver do you have? The model number is printed usually in one of the corners of the face of the radio. If you have the Pioneer DEH-150MP I recommend to change the EQ setting to FLAT, or Natural. This will lower the amount of bass. Simply press the EQ button found just to the left of the volume control. You can see a clear explanation of how to do this in this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-S6CDRdRSTCw.html You can find more videos about Pioneer DEH-150MP here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ywuLd0oQ_UI.html and you can find more videos on Pioneer's You Tube Channel here: ru-vid.com
The Pioneer DEH-150MP was first manufactured in 2011 and does not have Bluetooth. There is no way to add Bluetooth functions to this product. If you are interested in Bluetooth functions in a Pioneer in-Dash receiver, please check out some of the more modern products like Pioneer MVH-S310BT here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3OUfcKQ4nUA.html or Pioneer SPH-10BT seen here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2X0_WyTEMp0.html You can find more videos on Pioneer's You Tube Channel here: ru-vid.com
Hi,one of my cousins removed the radio without switching it off,now the words on the display panel are not showing properly how do i fix that,my heart is sore i just bought the radio recently 😭
If you don't see a fader control, you have the system set up with the rear speakers as subwoofer outputs. If you wan to change the rear speakers to full range output that can be done in the Initial Menu. You can see it on a similar Pioneer receiver here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Z6g0EOPZL0c.html I recommend to choose the Rear/Rear option. After this is complete the fader control will be available in the Audio menu. You can find a full playlist of How To videos from Pioneer here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ZCkYPPBBRkg.html and you can find more videos on Pioneer's RU-vid Channel here: ru-vid.com
Initial setup: REAR/REAR. You can see it on a similar Pioneer receiver here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Z6g0EOPZL0c.html This will give full sound to speakers in both front and rear.
What is the model number of your Pioneer in-dash receiver? Do you have the in-dash receiver set up with steering wheel controls? Improperly programmed steering wheel controls can cause unwanted mute operation. You can find more videos on Pioneer's RU-vid Channel here: ru-vid.com
The North American version of Pioneer DEH-150MP is shown in the video above and does not change colors. What model of in-dash receiver do you have? Many Pioneer in-dash receivers can change colors. You can see that here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-U9R5Ax_-nVI.html You can find more videos on Pioneer's You Tube Channel here: ru-vid.com
No, The Pioneer DEH-150MP does not have Bluetooth. This product was first manufactured back in 2010. Please consider a more modern Pioneer receiver like DEH-S4200BT here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-R5bEWdIAsFc.html or if you don't play CD's please consider Pioneer MVH-S320BT here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-cXbvdfgLS2o.html You can find more videos on Pioneer's You Tube Channel here: ru-vid.com
You may have the receiver wired incorrectly. You can learn more about the Pioneer Wire Harness System here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-kR2MO2kwFug.html You can find more How To videos about Pioneer DEH-X4800BT in this playlist: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-iLloPAn4y_o.html and you can find more videos on Pioneer's You Tube Channel here: ru-vid.com
Be sure to set the Fader control to 0 and the Balance control to 0. You can see that here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-WKPVQMgc6nI.html You can find more videos on Pioneer's You Tube Channel here: ru-vid.com
What is the model number of your Pioneer in-dash receiver? The video shown above is specifically about the Pioneer DEH-150MP. You can find a full playlist of How To videos about Pioneer audio receivers here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-42EL_JGXcJs.html and you can find more videos on Pioneer's RU-vid Channel here: ru-vid.com
Here is a You Tube video about the audio settings for a similar Pioneer in-dash receiver: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-XXOWoQLwyag.html and here is the video for the EQ settings: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-SQPXWW0l7Nc.html I recommend the Powerful EQ setting or Super Bass. Do you have a subwoofer in your system? If so I recommend a crossover of 80Hz. You can find more videos on Pioneer's You Tube Channel here: ru-vid.com
I recommend to press the SRC button to change the receiver to the AM/FM Radio Source. Here are a few videos about tuner operation ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-phdOvMbNmtY.html ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-sO3ZzIh9qsg.html ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-LGAOfg9QYtE.html ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ywuLd0oQ_UI.html You can find more videos on Pioneer's RU-vid Channel here: www.youtube.com/@pioneerelectronics