Thank you for the video. I thought I had to dig up 30 feet dirt to replace the supply line. I didn't know there was such thing as a coupling for galvanized pipe.
Just a tip on the coupling. If you can swing it use a dresser type coupling for a more permanent fix. They are high as hell but the longevity is far greater than the type used here. I use these for convenience but ive never considered them a permanent fix. If used be prepared down the line for it to fail. If you see a drop in pressure this would be the first place to check. The couplings im referring to have flanges and gaskets and bolts. They require more room but aside from rethreading or replacing lines its about the best repair method out there. The cost for a 3/4" compression coupling like used here is from 8.00 to 16.00 the dresser type would be in the area of 40 to 80.00.
Thanks your Sir, i have the same problem and was thinking of cutting and soldering the pipe. you method of using a coupler is the best fix, i learnt something, will try it out today, you just earned my Sub
I would have made the nipple longer to give more room for the coupling to compress, also would have chopped the threads off the nipple so they don’t damage the rubber, also would have sanded the pipe where the wrench left marks to ensure a good connection. But that’s just me 😅
whoever installed these pipes years ago didn't want anyone working on them without wanting to go crazy and call a plumber to dick with it, holy crap! Good video and work!
I have two minds about tightening the coupling over the threaded portion of the nipple; while it may help the rubber to hold, on the other hand, the threads may also cause the rubber to tear.
Yes but these couplings are also called a temporary coupling, because they do slip off over time I think. I am using one now on a steel pipe too, and it is leaking even though the ends are tightened all the way. I am thinking about applying some sealant around the inside of the ends. The rubbers on mine are different though, maybe your rubbers are a better design!!!
All these dresser couplings are temporary fixes. They last much longer on cold water lines, less on hot water lines. I’ve seen them last for over 20 years on cold water lines. But yes you are correct about these types of dresser couplings, they are not permanent. But you can get lucky sometimes.
Up here in Canada we call those dresser couplings. Honestly the best thing you can do with galvanized is just to replace anything that's exposed that shit is terrible.
Very handy tutorial. I don't at all know why...but having the coupler that close to the elbow bothers me. I would likely have had a longer new pipe on the elbow side and cut back more on the straight side. Would have offered a bit more room to work as well. JMHO. Lekker vid.
We have chicken houses and use propane with galvanized pipe. I have leaks where the pipes connect. Is there anyway to fix them without taking them apart?
Down here in Texas with the freeze breaking pipes. I have a 10 foot hot galvanized pipe that has a small crack in the middle of the pipe. Can I cut it and use this product for a permanent fix or is it temporary fix?
Yes, this is a great option for you to repair this thing. This is a great fitting that will last a long time. Although if I was you I would go ahead and replace all of your galvanized pipes with pex if you can. None of the stupid rust/clogging issues and it gives you a little more freeze protection since it can expand a little bit if it freezes. But you should insulate your pipes anyways, because even in texas it can get cold as fuck.
@@DG-ie5ip no i was not saying pex wont last long. I was answering the earlier question about how long the coupler will last. My answer was not about pex pipes. I was replying to DF comment. Galvenized do rust and split... especially when they are run in the ground.
You are supposed to put the hemp on in a clockwise direction on the thread otherwise it will push off as you tighten the joint , also it's always best to use some jointing paste with the hemp not water as you did....... 😜
@@Susan70003 .... it’s a linseed oil based paste with the consistency of tooth paste , it’s used for threaded pipes in gas work but can be used in water pipes but you need hemp as well to make a water tight joint , it’s mainly used in commercial and industrial pipe work these days..... 👍
Why hemp? Why not rector seal Tplus 2? It lubes seals and prevents corrosion. No disrespect intended but the majority of the people watching this prob wont have hemp laying around. They may have bud rolled up in some paper but the likelyhood of hemp is low.
If ur wife has long enough hair, or u keep horses on ur spot, yank some tail ,works just as good, hemp is superior to PTF, provided it's wrapped around clockwise