How To Fix Jammed FPV Motor 

Thanks, man! Was looking for Slatt's vid but yours popped up first. Did the trick and I thought that my motor was wasted. I could see that the bell was also deformed from the impact. I figured it was already broke so if I wasted a magnet it was no worse. Pliers on the bell and also some tweaking on the shaft and it works! Woot! Xing 2306.

Damn today my evoque f5d got stuck in a tree and it took forever for me to get it back to the ground.. was like 25 feet high and finally i got it down after like 3,4 hours of hard work and trial and error lol. But now i tried it and one motor doesnt work, even tho it look completely fine. The only difference to the other 3 working motors is that when i spin it by hand its just slightly harder to spin.. so im not sure if its the same issue as your video shows.. the drone landed on mud so it didnt get a hard blow on the motor but maybe that fall was enough to break it anyway. When i try to start it it just doesnt turn, doesnt even try to turn or anything, is just dead. But im exhausted for today lol, i will try your method tomorrow i think and i hope i can save it.. im getting a tbs tracer module soon and gotta buy a tracer rx anyway so if i cant save the motor then ill just also buy motor and will have to replace it sadly. Goddamn those trees fr. Thanks for reading my essay 😂

how did you remove & reinstall the circlip at the base of the motor? that's the part everyone wants to see!

Hey thanks Mah! I think that this trick will save about four motors that have suffered a jam, and were replaced with new motors. Thank you for the tip :)

Good video and thank you I can still fly my bent motor thanks!

Thank you, it was even faster and easier for me, then replacing other motor. Also you saved me some money, big thanks for you

Damn! Thanks for the tip! I mean since its all heading for scrap, worth a try and save $$$!

Legend 🫶🏽🔥

Brilliant video bruh!!!! My fix was.... dont use velox! 🤣🤣🤣

Ok so I can say that Slatt Fpv is right and is works an just about any motor ive done this with the pacers, F60pro’s

Thank you so much !

Worked for me, thanks

This is a sick tip, although I'd recommend against using the pliers like that - you may end up bending the bell inwards on the opposite side. My buddy F-Core showed me this, but he instead put a 1.5mm hex driver up thru the post and used that for leverage to bend it back. Usually when I have a motor that takes a dump, it's either because of this or because the rubber o-ring is worn away and the bell is scraping the windings.

Yesterday I jammed my motor of my cinewhoop. I crashed in very dusty place i turtle mode and then I couldn't take off so I also did the walk of shame to go and retrieve my drone. When I went there I tried to arm my drone and I saw that three motors were spinning okay but one was spinning slowly and stopping. I order a motor from banggood but I know I have to wait at least a month to arrive so I will try to fix it like you did. Thank you so much for the info. I just subscribed to your channel greetings my friend from Greece 🇬🇷

i can't even pull my bell.. lol... so hard

Sick rip

sg ?

Brilliant! This open area is pretty nice too, with that tiled pattern on the floor that looks like the ☯️ logo. 👍

keep it up brother 👍

Awesome dude. Love this a lot dude

Thank you man! My motor started being weird after a failed turtle mode attempt and this fixed it

For me the shaft is still straight, it is the bell thats bent, how do i fix that?

Great tips bro! 💯👍🏼👈🏻

Mounting the shaft in a drill and taping with a rubber hammer or a regular hammer with a old rag to soften the blow is the best way I've found. if you over tap it just use a flat head screw driver or something to bend it back a little. Try not to do too much back and forth cause it will fatigue the metal... small adjustments and then check it is the way to go. Hope this helps :)

Awesome bro!!!

Subbed and liked Great demo!

brooooooooo, you helped me a lot. Thanks

Nice rip bro🔥🔥🔥