I have thus problem, and now thanks to your video, I will check the power continuity today. I will message back to let you know how I go! Thankyou again for providing another path to troubleshoot.
@@ARTaudio440So I tried your checks, and I had continuity at the two small chips "U15" and "U16", and also had continuity when earthing the screw and checking "L35" and "L39" but that "L58" filter had no power going through it from either side, and the red LEDs on the switches no longer light up either. I installed a new screen because I thought that was the issue, but it hasn't helped anything...If anything I've made it worse 😒
@frayedsanity Hi, thanks for sharing your diagnosis, I can see that you have a missing volts on L58. Please check the reference volts as follows. L58 +9 volts Dc L35 -15 volts Dc L59 +15 volts Dc
hola Allan, yo tengo 2 pod hd500 con la falla mas comun de este modelo. al momento de prender solo aparece el logo y vuelve a empezar el procedimiento de querer cargar el sistema. tu sabes algo de esta falla y como repararla? te agradezco desde Mexico
Hi, thank you for watching☺️ Let me check your message and get back as I don't have copy paste in my fone to translate your comments. I need to access it on my PC.
I'm a little bit lost with this, is the sound output tied to the same component that was preventing the display from working? I have a unit that is getting no sound output but the display is working fine, should I follow the same steps you have here or should I be looking at something else?
Hello thanks for watching☺️ Yes it's tied up because -15 volts is a VLCD of the LCD which is the LCD contrast pulse. Follow my trouble shooting in this video and focus only on the pre-amp supply. Try to check the supply of U18 which is pre-amp of the headphone pin4 +15volts and pin11 -15volts.
If you gets +15 volts and -15volts meaning the pre-amp supply is good. Next to be check is the IC U40, U41 and U42 check this ic using your hand and feels if any one of these is getting more hotter than the rest. If gets hot, meaning that ic is the faulty one.☺️
Hello. I have a question. My hd500x has no sound output. Like, i can hear the one preset. But when i change preset it has no sounds. How can i fix this? Thank you for your response.
Hi, if the new version is available, please update it and reset it after. Make sure also that you are using the original adaptor or at least within the specs. Thanks for watching ☺️
Hi there, thank you for answering. I already try it 😢, but nonw of these things worked. When the pod self reboot sometimes it start a boot loop, but sometimes not. If it is on boot loop I need to unplug it and wait some time until it can boot normally
@@maxsuellima7488 For sure it has irregularities on the corcuit, possible loose connection of wire or faulty components like capacitor or crystal clock. I would suggest bringing it to an authorized service center. line6 is now under Yamaha.
my HD500x seems to be losing volume, the master starts to act from 3. in the calibration, the potentiometer seems normal. with volume at 4 I have an output voltage of 0.020mv. can you help me?
Hi Allan! Great video!... I have this problem... The volume goes up and down wile im playing... no knogs are touched... the volume changes by itself ... any help please? Thanks in advance!
Hi Kim, Thanks for watching. If it is the rotary volume, one of the reason why it's happening because of oxidations. You must open the unit and apply a contact cleaner where available to purchased localy like in hardware or electronics store. Actually WD40 will works but my preferred is Contact cleaner where it drys immidiately. If you are talking about the pedal then try to calibrate it. Attached link for pedal calibration. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2ejXOKyrUxo.html
Hi thanks for watching ☺️ If I have a chance, I will make it. Common problem for this model if there is issue on the sound is any one of the three ic is faulty. Its called DAC or digital to analog converter. Usualy if faulty, this ic gets hot or warm compared to good ic.
I have a pod hd bean desktop,same problem with you,i accidently burn it by wiring the rj45 jack to the switch. No sound no display just blank white screen.I checked the preamp opamps and the inductor,right voltage but still not working 😢
Hi, If all reference voltages are complete then possibly some of the components were damaged because it was not a normal breakdown. I would suggest bringing it to an authorized service center. Line6 is under Yamaha.
Hi sir. I have podhd500.The thing is that when i am playing a preset, a * symbol will show in screen and volume comes down when playing. Also the master know didnt work well. From workshop, they told me it was IC problem and also told me that this will happen twice if i got repaired. I dont know what to do. Please help!😕
Hi, is it authorized Line 6 Service workshop? Please watch and try this video about the calibration of the pedal. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2ejXOKyrUxo.html
Hi Allan, there is a Line6 pod x3 live that is being sold on the fb with the same issue (no sound and no display). The seller's tech told him that the issue is the processor but upon watching this video I'm now having second thoughts if I'm going to buy it and repair it myself or not. The question is, will this fix work on that unit too? Haha. His tech might be right if the real issue is the processor. Is there a processor available in the aftermarket? Will it be fixed if the processor will be replaced? thanks!
Hi po. Ang common kasi na problem ng model na ito ay ic. Yung regulator na related sa video ko. Pag may missing na supply ay ganyan ang symptoms. Pero kung na check ng tech na meron o kumpleto ang supply ay possible main ic na ang sira. Pag main ic na ang sira ay di na sya ma rerepair. Board replacement na.
Hello! I'm looking to replace my LCD screen as mine has faded out. Is it just a simple unscrew and screw-on type of a situation? A video would help too. Hope someone can help!
Hi, thank you for watching ☺️ I would suggest bringing it to an authorized service center to make sure no additional damage. Replacing the LCD is a bit difficult to unsolder the pins due to the double sided board.
Hello sir greetings from Indonesia. Thanks for your tutorial but mine a little bit different problem. My LCD goes bright and brighten when I turn on my line 6 pod hd 500x. What should I do?
also, if it has a usb port, plug into a computer and run Line 6 Monkey on it, update the firmware and that may fix your issue (and may not...but it did fix mine.)
Hi thanks for watching, Apply the pedal calibration on your Pod X3 live by keeping pressing the arrow right key while turning on the power. Please follow the screen message.
@@ARTaudio440 thanks for the reply. Did try that as per your instructions, yet no audio output. I did open the unit to see if I could get any further instructions.
@@awesamos During calibration, numbers must corespond when you move the pedal. If it is not happening then the sensor or the two parts on the pedal sensor board requires a replacement.
Sir my pod x3 live sound goes off whenever I touch the guitar input or output on the processor how to fix that can you please tell me I'm from India and i also wanted to know if I can get a footswitch replacement cause one of mine is broken and also the reading of original adaptor
Hello Vishall, Thanks for watching.l It seems that there is a loose connections between the audio cable PL and jacks of Pod X3. Pleas double check the guitar cables then apply a WD40 to output and input jack of pod x3 and jack of your guitar also. I can't help you with regards on foot switch. I will suggest to bring it to an Authorized service center nearest you. Original AC adaptor can be purchased online or local with the same specs.
@@ARTaudio440 Thank you so much sir but i dont know anything about electronics so can you send me your email id so that i can send you a small clip showing what going on with my processor.
Hello brother, i have pod 500x...it is continously restarting and no buttons were working, but now its fine and every buttons are working but there is no sound...please help me..i have few gigs coming this december...it will be a great help
@@ARTaudio440yes its the original one which i got with it...please sir, i need your help. what might be the problem..,?? By the way i used it after 3months..will that create some problem, like dust ..?? I tried other adapter also but it didn't fit.so no idea whether its a power supply failure or internal failure.
@@stur34gt @stur34gt Check pin 1 of U49 not sure if 49 or 48 ic next o coil that I was checked and behind R306, you must have get +9volts supply on that pin. If +9volts is there and still the same, then you need to replace that IC. Beacause U49 ic is a supply of the preamp audio output.
i got a fix for myself my power supply was kickn out 9.6 volts AC. apparently thats not enough mine is a older model, i have a Variac power supply. i turned up the power on the Variac until i had 10 volts AC. and it booted up with no problems.
Hello po kuya allan..pano po maiiwasan yung bootloop problem sa hd500 or hd500x? madami kasi nakaka experience nyan sa unit na yan sad to sya yung iba di na talaga nagagamit. Same nung sakin.
Hi po, sa ngayon ay limited lng ang info ko kasi kung ano lng ma check ko at available ay un lng tlga. Advise ko ay gummit po lagi ng original power supply adaptor at iwasan mabagsak ang unit.
My line 6 pod hd 500x is having issues with the amp display, whenever i power on the line 6 it load its patch and after few seconds amp display pop up for second ?? And it come and goes for second Who to fix it Need help ??
Hi thanks for watching ☺️ Try the global reset Turn on the power while holding down the arrow button left or right. If still the same Try it to update the sofware thru computer by installing line6 monkey apps or line6 updater.
@@longtartisso2806 Hi sir, sorry to hear that. I think it requires a deep diagnosing on your device. I would suggest to bring this to an authorized service center nearest to your place. Line 6 is under by Yamaha.
Hi, pa send po ng picture sa fb page. Artaudio440. Di ko kasi kabisado ang model. Marami kasi volts sa circuit. Ang volt ng audio ay -15volts at +15volts. Sa system namn ay 1.2 volts, 3.3 volts at 5 volts.
Sir yung sakin ayaw magconnect sa pc ano kaya possible problem ? Kahit updated na yung mga driver uninstall at install ulit na ginawa ko ayaw parin eh salamat sa sagot sir 😊
@@ARTaudio440 ou sir nagdownload na po ako nun autodetect siya ng model diba sir kasi yung hd400 ko nadedetect niya agad pag sinalpak ko pero yung 500x ko ayaw niya
Hello po Sir may unit ako na Line 6 pod HD500 ayaw nyang mag Boot or Factory Reset tapos ang nkalagay sa Display ay Line 6 lang nkakainis pero wala akong magawa sana po matulungan nyo po ako.
brother Allan, sakin naman mag on pero hindi mag start yong screen lang with the line 6 logo. ayaw mag start. may idea ka ba please let me know bro. salamat
Hello po sir, Pag ang issue po ay sa audio ay unang una kung merong abnormalities na supply sa pre-amp, pangalawa ay sa DAC ic or digital to analog convertion tapos loose connection sa audio output.