How to frame notch a G/A/B- body part 1 

I've done lots of notches,I just use a cutting wheel to start a opening top and bottom of the frame then I use a carbide tipped saws all blade a 8" to 10" and cut both at the same time clean cuts you still have to be careful, then do your finish grinding to keep them plumb,works for me.You'll run into a little issue with the car on the frame due to the rear end, lower control arms but it takes me maybe 10 mins per side to cut,then to make it look "stock" you can put a small cut top & bottom of the frame and just c clamp or heat and form to keep the shape.

👍👍👍Looking good.I Had to do fram notch and reinforce on my gbody 86 Cutlass to tuck 28s. I can do full uturn with nun of that reversing 50 times to park in a regular parking spot. 👍👍👍

LOVE UR VIDEOS FAM, NOT NO LIL, LEAVIN NIGGAS CLUELESS TYPE SHIT!!! U BREAK EVERYTHING DOWN, THANK U BRO💪🏾✊🏾

Good demonstration i need to do my Malibu i think I'm going to order the kit 👍✌

thanks for the video ken from pa. my son's want's to do some shit to a Chevy. I'm 59 years old.

Boi you steady dropping them hits!!! I definitely appreciate the excellent content!!! You a real one for showing each step most these folks just show you the finish product! So I definitely appreciate you!!! 🙌🏾🙌🏾🙌🏾🙌🏾💪🏾💪🏾💪🏾💪🏾💪🏾

2/16 😆 😆. I still like your videos bro. Keep making them. A bro I'm a Boilermaker by trade but just to help you out. When you go to do this again. Dont make a 90 on your corners because thats where you will get stress cracks at. Try doing a radius cut on the corner. Just at tip to help youre business out bro

As always nice work homie Just something to think about for guys on a budget or who might not have access to steel but bought the UMI kit or one of the other kits U can take the piece u cut off the front of the frame and clean it up real nice and trim it down to fit inside of the frame and weld it to the back side for some extra strength

6in lip on a stock rear end that’ll be nice that frame notch is fashow worth it bruh

Im the one that mentioned you making a video on this on instagram. Love the video great job

Yous a life saver I needed this to slap my 26 on 91 caprice

Good just bro thanks for the help

Alright dude, I'm gonna try to do it your way :) only think km gunna try, since I have 2 frames, and the back horns on the one are shit, is going be to try and taper the frame so that it doesn't have that abrupt notch at the front and back. Wish me luck haha

What's best part numbers on longer studs for front and rear with disk brakes for big rims ??

Yea man I found out about the lower lip being longer than the top. Posted that on my video too. That frame is tore up lol. Sand that down more to get good welds. With the gaps try to use slithers of steel to put inside it helps

So is this something that can be done without removing the body

Well done

Cutting torch would work also. Just cool it off regularly.

Did you make that drive shaft support

Got do mine them plate on back order 2 March 29

What kit were you talking about? Umi?

Where u guys get the plates for a 1972 a-body

👏👏👏✌

👍👌

It’s called back half the bars your talking about

Do u have the upper trunk piece my is rotted I need the pice in between the wheel wells

Mrgetinthere. Man. That metal seems pretty rusty. You sure it's going to hold up?🤔✌🏾💯

Need a frame notch on my 85 Regal where u located

Do I have to take the body off to notch the frame please answer me

Cut off wheel? F that time is money.

Best tip you will her here , don't buy harbor freight garbage .

Harbor freight is also chineese junk

M

Clickbait 👀

M