How to Hang a New Door in an Old Frame | Step By Step DIYers Guide

Подписаться 307 тыс.

Просмотров 207 тыс.

50% 1

In this video i will be showing you how to install a new door in an old frame. I will explain how to fit and trim a door as well as installing hinges, latches and handles . We will be looking at installing door furniture using a hammer and chisel as well as a hinge jig. If you like the content leave a like and please subscribe for more content like this as I've got a lot more to come and there will be something that will help you out.
Tools i recommend for this job below:
🔵 Winbag - amzn.to/3GdejMp
🔵 Self Centring Drill Bits - amzn.to/3QTCsxB
🔵 Magic Door Stands - amzn.to/3SAVycV
🛒 My Shop -www.amazon.co.uk/shop/thediyguy
► BECOME A MEMBER OF THE DIY CLUB Click! 👇🏼
/ thediyguy1
► Get FULL access to the Discord Group and other perks!
Follow me on Instagram 👉 the_diy_guy_youtube
Thanks for watching The DIY Guy. My mission is to bring you the best Tips, Tutorials and Tools to help you learn and save money.
Please be advised that this is only a guide which is intended for informational, educational and entertainment purposes and The DIY Guy cannot accept responsibility for any work undertaken. Be safe and have fun! The Amazon links above are affiliate links and as an Amazon Associate I earn from qualifying purchases. I may earn a small commission if you purchase via the recommended links, however this will not cost you any extra.

Хобби

Опубликовано:

10 ноя 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 279

@TheDIYGuy1 6 месяцев назад

What other carpentry jobs do you guys want to see?

@eggsRspecial 6 месяцев назад

How to replace a door frame 👍

@patburke5740 6 месяцев назад

Fitted wardrobe builds and alcove units. Maybe for the spring outdoor timber structures like pergolas.

@coolsujay 6 месяцев назад

Replace front outdoor lock, suggestion with smart lock if any

@darrenmackenzie1892 6 месяцев назад

Everything you know would be a start. Your videos are brilliant and great detail and very easy to understand.

@naebadyersel 6 месяцев назад

Could you do a video on how to make understairs drawers?

@prodical666 6 месяцев назад

Just want to say, between you, Robin Clevett and Peter Millard, I've basically got every area of home improvement covered. You're up there with the best of them. Keep it up.

@TheDIYGuy1 6 месяцев назад

Brilliant, thanks a lot 😊

@_tmmy_ 6 месяцев назад

Here’s little tip for fitting a door into an existing frame that I picked up off a family member. If you are using the existing hinge / latch screw holes in the frame and they feel a bit loose, grab yourself some bbq skewers or cocktail picks and dip them in some wood glue and knock them into the holes and trim flush. Works well for me in most situations 👍🏻

@TheDIYGuy1 6 месяцев назад

Good little tip!

@simonbaker3612 6 месяцев назад

Matchsticks too! Not the flamey bit (technical term 😂) though

@stevehowes 6 месяцев назад

@@simonbaker3612 The technical term for the bit you want to use is the "woody sticky bit"

@TheNorthernmunky 6 месяцев назад

Yep, I use match sticks

@davidhatton152 5 месяцев назад

😊😊

@trevorlintott598 4 месяца назад

Wish I'd seen them WIND BAGS 15 years ago..chisel ,screwdrivers ,packers all over the show.

@SilentAssailant 2 месяца назад

That teal wall paint looks great

@rajibalam9748 2 месяца назад

This is very helpful. Thank you!

@PaulSmith-vt1to 5 месяцев назад

Excellent video, very helpful. Thanks.

@johnoirie 5 месяцев назад

It's Absloutley amazing tutorial 👏... Thank you so much.

@maxelliot9426 5 месяцев назад

Excellent video, thank you

@nemonemo6285 5 месяцев назад

Perfect, thank you.

@jasonmorphew4359 6 месяцев назад

Thanks for this great video. I've hung a few doors in my 52 years and there was a few things i didn't know. Good job and love your videos.

@Alan-db4mq 2 месяца назад

Your videos and walk through step by step guides are top notch. A real help for a DIY novice like myself

@shaheenk4760 3 месяца назад

Thank you was amazing to see how easy it was to take off the stops. I want to turn the door so it opens the other way but was deterred from taking the stops off - but now I will. thank you.

@kotteeswaranmassmageshwar7625 5 месяцев назад

Your work very fine sir thanks

@scottball74 6 месяцев назад

Brilliant just brilliant i love watching you videos they are soo helpful keep them coming

@TheDIYGuy1 6 месяцев назад

Thanks, will do!

@elpresidente8730 Месяц назад

Excellent video and just at the right time as I'm going to be fitting 11 doors in a few weeks with rose style handles so this video was the perfect one for me. Thanks for sharing the knowledge.

@cprog 6 месяцев назад

Thank you for your detailed tutorial!

@TheDIYGuy1 6 месяцев назад

You're very welcome!

@markevans8596 6 месяцев назад

Thanks for this Cameron. Out of all of videos that you’ve put out I probably found this one the most useful. I’ll definitely be referring back to it in the future. Thank you!

@TheDIYGuy1 6 месяцев назад

Brilliant, glad it’s helpful 👍

@barryspencer831 Месяц назад

Great videos mate just used this tutorial to hang 3 doors never done before but you made it look easy,thankyou

@flyprincess69 3 месяца назад

Greatings from the USA. Im chopping hinges today.

@TheDIYGuy1 3 месяца назад

Hello and good luck

@DjGiluk 6 месяцев назад

Great video, thanks 👍🏻

@TheDIYGuy1 6 месяцев назад

Glad you liked it! Cheers

@rodgerq 6 месяцев назад

Another great video. I think on those door handles with the slit in the square bar, the slit goes vertical so that the grub screw drives into it, spreading the bar and making it grip the inside of handle. I think!

@daveandden 2 месяца назад

Great Video and nicely explained. thank you.

@TheDIYGuy1 2 месяца назад

Glad it was helpful!

@jonno946 6 месяцев назад

Love your videos need to hang a door soon, never knew about the hinges being different on each side thanks

@TheDIYGuy1 6 месяцев назад

Happy to help!

@hawknottopgun5891 Месяц назад

The air bags are such a solid tip, makes solo-ing a job like this a lot easier

@TheDIYGuy1 Месяц назад

👍

@munyag766 6 месяцев назад

The most acute and easy to follow tutorial on RU-vid. Thank you so much

@TheDIYGuy1 6 месяцев назад

You are welcome!

@Samrichards413 4 месяца назад

Watched your first clip and after that been watching your videos ever since. Great content here and chunk of knowledge and experience I look forward for plenty DIY videos 😊

@TheDIYGuy1 4 месяца назад

Awesome, thank you!

@markhannan4712 6 месяцев назад

Very well explained I’ve fit a lot of doors in my time and everything you have shown is spot and should be very helpful

@TheDIYGuy1 6 месяцев назад

Glad you liked it! Thanks

@pnd7727 6 месяцев назад

Buzzing pal, gonna try my own with your tips. Thanks a million.

@TheDIYGuy1 6 месяцев назад

No problem 👍

@macbook9084 3 месяца назад

Another great video sir Thank you!

@TheDIYGuy1 3 месяца назад

You are very welcome

@Andy-no1gc 6 месяцев назад

thanks for the film, it is very helpful, best regards

@TheDIYGuy1 6 месяцев назад

Glad it was helpful!

@johngordon3164 10 дней назад

This is a fantastic educational video. I’m about to hang 9 doors… I’ll report back in a bit (if I survive).

@TheDIYGuy1 10 дней назад

👌

@olliecooper933 3 дня назад

He didn't survive

@peternash4936 27 дней назад

Hung a door today following your video ,brilliant worked a treat.👍👍👍👍

@TheDIYGuy1 27 дней назад

Great job!

@kabsism5155 6 месяцев назад

Thank you and keep up the great work.

@TheDIYGuy1 6 месяцев назад

Thanks, will do!

@jamierandell348 6 месяцев назад

Awesome job thanks 👌👏👏👏

@TheDIYGuy1 6 месяцев назад

No problem 👍

@deiver2492 2 месяца назад

very useful video! thanks

@TheDIYGuy1 2 месяца назад

Glad it was helpful!

@patburke5740 6 месяцев назад

Excellent tutorial, seen all your videos and this is one of the best youve done. One of the best diy channels on you tube.

@TheDIYGuy1 6 месяцев назад

Thanks so much 😊

@Kapitansim 6 месяцев назад

Amazing ,thank you

@TheDIYGuy1 6 месяцев назад

Thank you too!

@tempestdesert470 9 дней назад

fantastic explanation... I come from another country but I bought a house in UK(beautiful country), after your video I changed the first door in the house myself... it was almost perfect...thank you

@TheDIYGuy1 9 дней назад

Glad it helped!

@MatthewCornish 6 месяцев назад

That's really useful, thank you :)

@TheDIYGuy1 6 месяцев назад

Glad it was helpful!

@marshp3 6 месяцев назад

Great video.. I've hung loads of doors but this is a great primer/fresher well done

@TheDIYGuy1 6 месяцев назад

Thanks 👍

@RichardDowd 6 месяцев назад

Brilliant tutorial!

@TheDIYGuy1 6 месяцев назад

Glad you liked it!

@RichardDowd 6 месяцев назад

@@TheDIYGuy1yeah, as you've n doubt seen, tube vast majority of tutorials are on new frames. My house was 'renovated' by a cowboy before we bought it. He put in new doors but they are more of a hexagon shape 😬🙄 and the frames have been hacked away all over the shop 😮😊

@ddfann 6 месяцев назад

Excellent video

@TheDIYGuy1 6 месяцев назад

Thank you very much!

@mea03wjb 4 месяца назад

Awesome stuff... 10 naff 60s doors to replace at my place and feel ready to take it on now

@TheDIYGuy1 4 месяца назад

💪 you got it

@masa4936 6 месяцев назад

This is a great tutorial, exactly why I follow 😎

@TheDIYGuy1 6 месяцев назад

Glad you liked it! Thanks

@Lloyd69 6 месяцев назад

Always interesting to see how people do it so differently to how I was taught to hang a door. I would start by putting a leading edge on the door and only plane down the latch side. The air bags are a game changer too, one of the best tools a second fix carpenter can have.

@Skyline26r33 6 месяцев назад

Very good video very well explained makes my life a lot easier 👍👍👍👍

@TheDIYGuy1 6 месяцев назад

Glad it helped

@Andy.of.all.trades 6 месяцев назад

Amazing timing! Was out last night surveying a client's rental that they want to refurb. Replacing doors all round was one aspect. Never done it till now (am part time in this gig at best). Confident that I could get it done now. Thanks! 😎

@TheDIYGuy1 6 месяцев назад

That’s great, glad to be of help 👍

@davidjohn05 6 месяцев назад

Superb Video. Like all your videos the procedure is shown step by step. You make it look easy (although I know from experience it isn't). Thanks again for making these videos

@TheDIYGuy1 6 месяцев назад

Thanks a lot! I try my best to make it nice and simple and inspire others to try and do things they normally might not.

@TheNorthernmunky 6 месяцев назад

Good tutorial mate

@TheDIYGuy1 6 месяцев назад

Glad you liked it

@Wonkabar007 4 месяца назад

Thanks for this upload really helpful, I had to take quite a lot off the height and I used a mini circular saw which really struggled cutting through the hollow door, so I've ordered a full size circular saw, seems when it comes to power tools you don't want tools that only just manage to cut deep enough, it's best to have plenty of redundant depth and power.

@TheDIYGuy1 4 месяца назад

Glad it helped! Enjoy new tool day 😊👍

@renwickfonceca7552 3 месяца назад

Very informative, could you please share a video of installation of a large door like 1200mm and what hinges do you recommend

@keitho77 6 месяцев назад

Great video. Just wish I had a door to replace now 😉

@TheDIYGuy1 6 месяцев назад

Do it just for the practice 😂👍

@joshlovingoutdoors4455 6 месяцев назад

I loved the tutorial, very practical steps, I think it still takes experience with carpentry work to pull this off but

@TheDIYGuy1 6 месяцев назад

Glad you liked it!

@darrenatarrant 4 месяца назад

Great video and lots of good tips. I’d recommend not using an impact driver on screws that come with hinges, handles strike plates etc as they typically can’t handle it - especially if they’re brass and you’re hanging the door a few times during the process

@adzg4m1ng85 2 месяца назад

Something I've found if you find your new strike plates are much smaller than your old ones. It gives you wiggle room to place the new ones just 1mm off centre of the door frame to the side. That way you can avoid having to lever off the door stops to relieve tension. Then just use filler to fill in the space around the plate where the old one once sat.

@Mclaneinc 6 месяцев назад

I hate doors (hanging them, I mean) so this was a great load of help Cameron. Loved the detail and the little funky tools. Nice one as usual. As for other chippy stuff, building frames for work tops would be nice, maybe with drawers to maximise the cupboard space, I never know what is the best way....Just a thought....Yet again, top vid young sir.....Paul..

@TheDIYGuy1 6 месяцев назад

Thanks Paul for the feedback and suggestions 👍

@Mclaneinc 6 месяцев назад

@@TheDIYGuy1 I genuinely love these videos, it gives an old 'wannabe' a fresh enthusiasm about DIY. I'm sure I'm not the only follower that feels that. Deserved Cameron, deserved..

@TheDIYGuy1 6 месяцев назад

👍👍

@Del1ng 6 месяцев назад

@The DIY Guy, another great video. Would love to see a door replacement fit in an older house (1920`s for example) where the door frames are no longer square due to old movement (frames, wall opening) over the decades. Cheers

@TheDIYGuy1 6 месяцев назад

Great suggestion! Thanks

@monkeyboi282 5 месяцев назад

I was about to comment this too. Mine are so out that it can be in line at the top of the hinge side, and the lock side at the top will be an inch away 😂

@cdyz5 Месяц назад

Thank you mate very detailed and good presentation. I am going to attempt to change my house internal 8 doors this summer. Your video is very knowledgeable and I need to watch this many time may be 20 or 40 time to get the confidence to give me the start. Apologies you might already have mentioned this in the description but would be great to know what tools and the names of the tools you using as I am new in this game. I don’t want my wife making me football and yelling what the mess I have created. Cheers l and once again thanks for the detailed explanation.

@stuartkidd3624 3 месяца назад

Very good video, I don't like hanging doors as I'm never happy with the result, I have one to fit at the mother in laws on Monday, it's even the same door from Wickes, feel more confident having watched this. Thanks 👍

@TheDIYGuy1 3 месяца назад

Thanks, you’ll be fine 👍

@PSNvjimmy 6 месяцев назад

Great video. I’m a complete novice so may be wrong but the last two steps should they be the other way round? Should you do the strike plate swap before adjusting the stops as the strike plate could change how the door shuts slightly?

@carpinteroespanoleninglaterra 3 месяца назад

I always check the gap between the hinge leafs because sometimes its 2, 3 or 4mm when closed then that will affect your 3mm gap around the door

@darrenmackenzie1892 6 месяцев назад

The painting finish on your frames are top quality. Any suggestions how you did it? Cheers

@jazzyb8886 6 месяцев назад

Brilliant job. Wish I hadn't used certain builders to do ours because they did such a poor job in comparison!

@GinasWorld9 Месяц назад

Thank you, this covers everything I’ve be been worried about but my first ever door fitting will be fully glazed. Aside from extra care in handling, are there any other glazed specific tips or advice you can offer?

@TrickyTree84 6 месяцев назад

Matchsticks or cocktail sticks for existing screw holes. I uded that to movr the hinges a bit rather than messing about with moving the stops

@djfunkycraig 2 месяца назад

It takes longer to for the jig and electric router than it does for ol school chisel, great vid though cheers mate keep up the channel!!

@benmakepeace5759 6 месяцев назад

Nice quick cut away from those ruff hinges 😂

@125sm3 6 месяцев назад

Great video and very good instructions 👍. The only thing I would like to add is aimed more at the novice is if your new handles aren't spring loaded then buy yourselves a spring loaded latch. Not picking fault with your content which is excellent just adding a little bit of advice. 😁

@TheDIYGuy1 6 месяцев назад

Absolutely! Always welcome extra tips and advice here on the channel!

@stefanrocker2890 6 месяцев назад

Danke!

@TheDIYGuy1 6 месяцев назад

Thanks to you too!

@johnhowley-zi6db 6 месяцев назад

Fitting window frame would be handy

@marney720 3 месяца назад

Awesome vid as always! Quick q if you don't mind...assuming the old door is a good fit, could you not lay it on top of the new door and then mark the hinges, handle position etc? Cheers!

@alidas1435 6 месяцев назад

great job.. i need external renderer in london would u recommend any website to find one?

@bettyswollocks5278 6 месяцев назад

Tip-top-top-tip….Before you remove the old door have a look how it sits in the frame. If it’s a perfect fit simply remove it, lay on top of your new door and trace around it. Let’s say it’s a couple of millimetres shy in the top left corner, write +2mm on the door at this point and it’s 3 millimetres shy on the bottom right so write +3mm at that point. Then remove the door, lay new door on top and add the extra millimetres where you’ve made your reference points and then trim to these lines.

@TheDIYGuy1 6 месяцев назад

Good tips 😊

@JP_TaVeryMuch 6 месяцев назад

The quickest and simplest wooden frame for a Christmas tree that will survive the festivities in the tree's bucket of water too.

@TheDIYGuy1 6 месяцев назад

💪👍

@daniellesears8612 3 месяца назад

Great video! Where do you get the 3 mil door packers? I’m looking online in the USA and can’t find them. Thank you!

@FSX3000 3 месяца назад

i saw the spade bit and thought of this video of Adam Savage i saw a while ago that talks about forstner bit 😂 they are way better than the spade bit just in the small chance you haven't heard of them

@Pete.Ty1 6 месяцев назад

👍👍👍.Thanks

@TheDIYGuy1 6 месяцев назад

Welcome 👍

@MalcolmJames-sg3zg 6 месяцев назад

Well explained videos , 😂

@TheDIYGuy1 6 месяцев назад

👍

@TheNomadicTrader 6 месяцев назад

Amazig video

@darrenmackenzie1892 6 месяцев назад

This guy really needs sponsorships from the best power tools!!!!

@TheDIYGuy1 6 месяцев назад

I agree 😂👍

@marksweetman8765 6 месяцев назад

Excellent vid but I would have fitted the new striker plate before moving the door stops

@TheDIYGuy1 6 месяцев назад

👍

@BSmith244 6 месяцев назад

It was all going so well until you said 38mm was half way between 72mm for the hinge. It looked more like 76mm on the rule so I’m sure it was just a slip of the tongue 😅. I have a couple of new doors to fit in my daughter’s house soon and I’m sure this video will prove helpful. The windbags seem a great idea and I’m probably going to order some. Many thanks

@djuav 6 месяцев назад

Absolutely loving the content mate, quick question, have you ever done work on a flat roof single story extension where there looks to be a leak in places, iv got this myself and looking at DIY’ing to get me through the winter, everywhere is choc a block with work and no one can get out, thinking there damage to the flashing along the gable but need to get up to inspect properly, thought I’d ask to see though, appreciate what you do lad, interesting and educational content!

@TheDIYGuy1 6 месяцев назад

Yep, go for it. If it is the flashing it should be simple. You can buy flashband at screwfix 👍

@Audit-The-Auditors 3 месяца назад

'Heightf' is now my word of the day.

@stephenshaw7980 2 месяца назад

When I went to school half of 72 was 36 not 38😂. Great informative video though, got the wind bags and self centre drills on order

@gawo2546 4 месяца назад

What's the solutions if the old door frame is not level or is crooked. So there are 3 different measurments of width of door at top, middle and bottom. Would you trim the door where catch or frame bit back?

@dgmclar 2 месяца назад

What do you recommend if the frame isnt square or level?

@markfroggatt591 20 дней назад

I'll give you the best tip of all , get a joiner in to do it. Save you a lot of time money and heartache 😂😂

@CraigMarks-tb3qo 4 месяца назад

I’ve just replaced bathroom wall, door frame and door and Thanks to your video, that’s the easiest door hanging I’ve ever done. Only problem I found is that after hanging the door the gap on the hing side was less then 3mm and the gap on the lock side was too big….could that be because of cheap hinges 🤔

@lorriemamoet9406 Месяц назад

Please do one on how to hang a stable door

@leedavey04 6 месяцев назад

Think I have watched all your videos now and very useful too….but can you tell me if you finished building your man cave/Shed in your back garden yet?

@TheDIYGuy1 6 месяцев назад

Thanks. Not yet, we have a foundation /concrete pad and I’m editing that video for release very soon. Materials for the structure arrive next week and walls and roof will go up 👍. All will be filmed step by step 😆

@blazeftp Месяц назад

Question i can't screw through to fix the handle as all the holes are right where the latch is ?

@markbooth804 Месяц назад

Obviously DIY everything 240v, and use the depth gauge on the router to set the hinge depth

@6Shery9 6 месяцев назад

I wanted to replace an old door with a cheap door from Wickes but the height opening is only 1900 and all the doors I have seen are around 1980 with only 10mm trimmable so i really don't know what to do without spending a lot of money on proper expensive door made of solid wood throughout. Any suggestions?

@nathanbell612 6 месяцев назад

What do you do if the room that the door opens into has a slightly higher floor????

@tomlock9429 3 месяца назад

What should i do if the old hinge cutouts on the door/ frame have been cut too deep?

@lewisbrown51 6 месяцев назад

Here's a guy you'd be happy to have work in your house ... 👏. Guy who put my new doors in could do with watching this, practicing, and apologising to me!!!

@TheDIYGuy1 6 месяцев назад

Glad to help and thanks

@Scottymol 6 месяцев назад

Great Video, I've got 4 doors to do soon, I've done them before but it's always a long time between fitting so always good to have a refresher and some tips.

@TheDIYGuy1 6 месяцев назад

Absolutely👍

@Jonno-Bass Месяц назад

What if you need to make a new door frame as the space is far larger than the door? I have two old solid wood doors 2020mm x 820mm that need mounting in spaces 2350mm x 90+mm.