No video :(

How To Heat Shrink Fiber Optic Cable Into A Live 400D FOSC

Подписаться 5 тыс.

Просмотров 4,5 тыс.

50% 1

In this video, I will be explaining my techniques for entering a new cable into a Live 400D Commscope FOSC as well as a few other tips and tricks throughout the video. Thanks for watching Please like, Subscribe, and comment any questions you may have. if you would like to support the channel and get some exclusive content, and consulting please check out my RU-vid membership tiers as well as Patreon you can message me directly on both memberships for direct help to any issues you may be running into in the field.
patreon.com/FiberSpliceGod

Опубликовано:

24 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 28

@Steelwind88 7 месяцев назад

Great video! One tip to opening the ports, i use my heatgun to warm up the port end. It would make softer and easier to cut. As well, the cut was normally not as sharp as cutting it without the preheat.

@SuperSync 7 месяцев назад

Came here to say exactly this.

@fibersplicegod 7 месяцев назад

Very great point I will have to give it a try on the next build thanks for watching and commenting I appreciate it

@mistermac56 5 месяцев назад

Nice work. Like your commentary as you go about your work and how neat and tidy your work is. At the college I worked at, and was the WAN tech (I retired five years ago), we had AT&T install eight Metro Ethernet circuits in our data center, that connected our remote campuses throughout the state via pure Ethernet. Two AT&T fiber install techs did all of the fiber work. They banged that out in no time. My jaw was on the floor. lol There was a FOSC mounted on a thick marine board that was bolted on the wall at the fiber demarc point in the data center. The AT&T Metro Ethernet techs connected the equipment and tested everything. Everything was completed in a day. The remote campuses already had their Metro Ethernet circuits and equipment installed. We cut over from DS3 service to Metro Ethernet in four hours.

@fibersplicegod 4 месяца назад

Hey thanks for watching and commenting I truly appreciate it🙌🙌 yea I build networks for all large providers. Nice yea you just have had some quality techs on site me and my guys can deploy any size network in a very fast manor the most recent somewhat bigger network was a new development 240 new lots we placed spliced and tested the whole network in 8 days was over 10km of cable along with another 2km feeder network to connect the new distribution cabinet we installed back to the main C.O it was a nice quick one. Once again thanks for watching and commenting I truly enjoy meeting and conversations with others in the industry

@lornamacmaster9985 7 месяцев назад

Great work as always

@Barthal56 7 месяцев назад

Amazing video! Love seeing the explanation of how the entire procedure is done step-by-step. Are you based in Alberta?

@fibersplicegod 7 месяцев назад

Thanks for watching and commenting I really appreciate it. My company is based out of Alberta but I do work all over Canada

@oc91five 7 месяцев назад

At 11:05 minutes. Use a fiber heat gun to pre heat that top. With a razor it will cut off like butter.......

@alboiu 7 месяцев назад

Nice work. Great video . Thank"s a lot !

@fibersplicegod 7 месяцев назад

Thank you for watching and subscribing I really appreciate it new video coming out tonight🙌

@irvinfuentes9509 5 месяцев назад

I wish I want to work someday like your job.

@Henry-vq6tl 4 месяца назад

I would heat up my blade with a touch or heat gun to cut that backing like a hot knife though butter. I know that part can be a knuckle buster!

@fibersplicegod 4 месяца назад

Yea I’ve had a few people mention this I do it every time now hahah no more knuckle busting 😂 thanks for watching and commenting I appreciate it

@Henry-vq6tl 4 месяца назад

@@fibersplicegod keep up the good work out there some of your videos have helped out some of are new guys.

@mlpmail 7 месяцев назад

If you get a heat gun, get a concentrator nozzle for it. The heat gun I use is not hot enough without the nozzle.

@kickstartnetworking3347 6 месяцев назад

I can see that you don't leave any buffer slack, that is paramount in my country in case the cores are broken in the tray for any reason, in fact I have seen it happen, and with a buffer slack you just have to strip more buffer and you are ready to go.

@fibersplicegod 6 месяцев назад

This was an existing live fosc that was built years ago I was just simply adding a new cable to it. I always leave slack in the basket and in the tray when it comes to ribbon fiber. Unfortunately the tech who built this original fosc did not leave slack in the tray. Thanks for watching and commenting I really appreciate it

@charvesbucknor2894 4 месяца назад

Im looking to become a splice currently been doing ftth installs 2yrs now how can i get into osp splicing

@fibersplicegod 4 месяца назад

Hey thanks for watching and commenting. The best way would be to find a contract splicing company like myself and give them a call or another way would be to start your own company and ask who employs you now and ask to get some small splicing jobs

@zivh5237 6 месяцев назад

hI, do you have a video on how to mid spann a tube in 96 fiber cable to connecto to drop cables ? like in /out 96 that one of the tube dome of it get spliced to drop

@fibersplicegod 6 месяцев назад

Hey thanks for watching and commenting I really appreciate it. I don’t have a video of this particular scenario but have dealt with in numerous times through out my career. To explain it quickly it comes down to how many fibers you need to splice out of the 96f midspan to the drop cable. If you have multiple drops you are needing to connect and it equals 12 fibers needed one whole tube then it’s as simple as just cut that tube and bring it to tray. If you are only needing one or two fibers out of the 96f then you need to bring the midspan tube up to tray and use a small midspan stripper to expose the full 12 fibers and then just the 2 fibers out while leaving the remaining 12 in the tube as one going in and out and store in the tray nearly. I will make a video on this the next time I run into it. Thanks for commenting and subscribing I really appreciate it

@VaporMLG Месяц назад

Gotta be careful those cases ain’t no slack basket I see

@Bacharus 7 месяцев назад

35:12 This fragment of the video is repeated

@fibersplicegod 7 месяцев назад

Just seeing this now I really appreciate you pointing this out and letting me know. Just finished cutting that part out video should be good to go in a short while once RU-vid recognizes the changes. Thank you so much and thank you for watching and commenting I truly appreciate it 🙌

@Bacharus 7 месяцев назад

You forgot to treat the cable sheath with alcohol

@fibersplicegod 7 месяцев назад

Hahah yes you are right I did not treat the dry loose tube cable with alcohol in the video but I did give it a nice clean alcohol wipe right before ribbonizing to remove any residuals from the fibers to ensure a quality ribbonization 👌 thank you for watching and commenting I really appreciate the feedback more videos coming soon

@lornamacmaster9985 7 месяцев назад

Good to know that people are paying attention