How To Install A 3 Inch Rear Lift Kit For Chevy Silverado 1500 (GMC as well)

klowny1969

Подписаться 94 тыс.

Просмотров 172 тыс.

50% 1

How to install a lift kit for the rear of your truck.
**Its also a good idea to check the u bolt nuts after 100 miles or so to make sure they are tight.
Check out my other videos:
How to change a tire pressure sensor (TPMS) yourself:
www.youtube.com/watch?v=PDpDm...
Dakota digital dash Install (1982-1992 Camaro)
• Dakota Digital Dash In...
How to install a 4L60E transmission:
• How To Convert a Stick...
How to Wire A Switched fuse block:
• How To Wire A SWITCHED...
********Get your klowny1969 Shirts and Apparel here:
teespring.com/stores/klowny1969
SUBSCRIBE TO MY CHANNEL! Also check out the videos below!
Complete Brake Overhaul:
www.youtube.com/watch?v=TVA0t...
Vintage air serpentine setup:
www.youtube.com/watch?v=ByVdD...
How to Upgrade your fuel pump:
www.youtube.com/watch?v=8-7sB...
How to install an electric vacuum pump:
www.youtube.com/watch?v=i1n3b...
How to build a camaro from top to bottom:
www.youtube.com/watch?v=5twT_...
400 Cubic inch small block Dyno testing:
www.youtube.com/watch?v=eavm4...
How to Clock an Alternator:
www.youtube.com/watch?v=_I24m...
How to Replace a u-joint:
www.youtube.com/watch?v=QQsXs...
How To install a trans pan drain bolt:
www.youtube.com/watch?v=zXFCB...
How to install subframe connectors:
www.youtube.com/watch?v=9n1Yc...
How to do a quick wheel alignment (toe in toe out):
www.youtube.com/watch?v=Ycdoo...
klowny1969 - best car mechanic on youtube
Only clown mechanic in the world !
This video can be applied to chevy, ford, mustang , impala , camaro , corvette, truck , toyota, lexus , honda , nissan. etc.. volvo cadillac

Авто/Мото

Опубликовано:

3 сен 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 72

@stacydornan9765 4 года назад

Good job BRO,keep the vids Rollin Klowny,you the man

@LookInDJProduction 2 года назад

one of the best instal video in details ;)

@klowny1969 2 года назад

thank you..dont forget to subscribe

@TheProbegt93 Год назад

Thanks for the video... I wasn't sure which shorter end of the block it had to face but now I do.

@klowny1969 Год назад

Glad I was able to help..dont forget to subscribe

@supremebeans1004 2 года назад

Right to the point and kinda funny too. Perfect video

@klowny1969 2 года назад

Thanks..don't forget to subscribe

@supremebeans1004 2 года назад

@@klowny1969 already am my man you make some great content that really helps alot of people. Keep it up 👍👍👍👍👍

@corygardner3732 3 года назад

What size lift do you have in the front? I have a 4” lift in the front now I need to add to my Rr but trying to see what I need to get to make it level.. so far it’s 2” lower in the back

@Kannon91491 2 года назад

I have a 97 4wd tahoe that im trying to put 24”rims with off road tires on what size lift will be the size that i need for it to fit?

@jimmysegovia2688 2 месяца назад

Awesome job klowny! Hey klowny I have a 99 dodge 3500 van where can I get these blocks and u bolts? Thanks for sharing klowny.

@BillysWild 3 года назад

Awesome video! Thank you for an in-depth explanation. A lot of the mechanics on RU-vid expect non-mechanics to know some of the stuff they’re doing.

@klowny1969 3 года назад

Thanks for watching and commenting..don't forget to subscribe

@blakepetty8526 Год назад

Can you get the same ones for the front and the back

@user-yi8pf8on6w 2 года назад

How did you lift the front, just a levelling kit?

@brianirwin9072 2 года назад

Good video I’ve seen yet when I did mine axl rotate forward you got to use the flange on in axl and jack it up to align it that was my situation but video explaining it

@klowny1969 2 года назад

Thanks for commenting and don't forget to subscribe

@DeadpoolCore 3 месяца назад

so the u-bolts are basically holding up that side of the axle??

@your_highn3zzfabito398 Год назад

how much did you torqued em for??

@kevinaragon8011 4 года назад

Good job!

@klowny1969 4 года назад

Thanks..dont forget to subscribe

@kevinaragon8011 4 года назад

@@klowny1969 sure!!

@calk2005 Месяц назад

can i put no block and just take out the stock n drop it

@702xRyder 3 года назад

Cake job no bs just to the point

@klowny1969 3 года назад

thanks for watching..and dont forget to subscribe

@fixitlinc3339 2 года назад

Good vid. But torquing is really important i feel

@Mason-to9fv 2 года назад

Looks awesome anything else I should double check once done tricks ?

@klowny1969 2 года назад

Give it a week or so and retorque the nuts...don't forget to subscribe

@DGG-xw1wj Год назад

When lifting the rear like this, what parts are prone to wearing out? What will I need to replace in the future?

@BigCountryKracker Год назад

In the rear nothin, there’s not much to the rear. In the front u can expect upper control arms to wear or tie rods if u didn’t get new ones. If u got a cheaper lift that don’t come with a diff dropand have 4WD u can expect CV axles but back you’ll be fine

@JayLupe 4 года назад

At 5:15min, did you over tighten that bolt..? Or was thart normal? Honest question

@klowny1969 4 года назад

they have to be real tight..drive around and retighten them..dont forget to subscribe

@trawright8781 3 года назад

Do you need to install shocks in order to lift a 2007 Silverado 3inch?

@mylesmour5683 2 года назад

Yeessssss

@xxigotnuggs_____8336 2 года назад

Either you get new struts or they make extenders that allow you to use your factory rear strut

@ismaelcarrillo3956 Год назад

Not unless you what that HD suspension ride

@m111mqtr 3 года назад

From the front how many inch

@yatox8 Месяц назад

2:28 you were about 1" from disaster.. those wood blocks were doing hella jenga.

@klowny1969 Месяц назад

You gotta live life dangerously sometimes..don't forget to subscribe 😉

@patrickjohnson7801 Год назад

Might need to install shock blocks as well.

@markmathews5117 10 месяцев назад

Your right.. Even with my 2 inch blocks I needed longer shocks..

@user-ts1jx8pk8m 3 года назад

助かりました　ありがとうございます Thank you for the great video

@klowny1969 3 года назад

Thank you sir! if you aren't subscribed, please do!

@blkicemike4857 Месяц назад

Folks I can NOT get holes and pins to align ,. I bought 3.5 front , 3 rear level kit for my 2017 Silverado,. Honestly I have had pure HELL outa this level kit,. The kit is KSP brand and I have already gone thru two sets upper control arms, now I’m on my 3set bushing for the last set uppers I installed,. They’re fuking junk!!! Last about 3months,. I’d put factory uppers bak on but at the time of installation I gave them to my neighbor for his truck,. He still using them😂,. Bak to the rear block installation,. What could I be doing wrong, they won’t line up(holes and pins on blocks /leaf spring)??? I’m to the point of trashing this KSP kit and ordering the Grunion lift,. Cost is more but looks hella more stable!!!