How to install a Holosun 507C

Подписаться 11 тыс.

Просмотров 24 тыс.

50% 1

Holosun 507c X2 installation. Unboxing and mounting.
#workmanfirearms #holosun #507c
Legal Notice: All content on the Workman Firearms Training Group RU-vid channel reflects our own opinions and should NOT be taken as legal advice. Please seek out the guidance of professionally trained and licensed individuals before making any decisions.
Disclaimer: These videos are strictly for educational and entertainment purposes only. All work on arms should be carried out by a licensed individual and all state and federal rules apply to such. We (including RU-vid) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of our videos.

Опубликовано:

15 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@spaceman063 2 года назад

I just noticed that you didn't use a mounting plated but attached the holosun directly to the slide !?

@jaybirdtapsnracks3460 7 месяцев назад

This is probably not an MOS Glock, rather a custom slide milled for a Holosun. No plate needed, but you can only run reddots with this pattern footprint. This is how I run my Glocks, with the milling done by Jagerwerks.

@SwampJesus23 Год назад

Did you use the longer screws or shorter

@cryeredd7563 4 месяца назад

did you sue the shorter screws or the longer ones?? also, i'm assuming that's an aftermarket slide?? the oem ones need a mounting plate in my experience... this wouldve been great info to include!!!

@johnarsenault1202 9 месяцев назад

nice , clear, thought out presentation. well done, and thank you.

@waldoherrera1427 Год назад

Thanks much; very useful.

@tonymarinelli7304 Год назад

Did you put the Loctite just on the tip of the screw? Thanks.

@AustinOutdoors. Год назад

Normally yes you put it just on the tip it’s not good to over loctite it

@tonymarinelli7304 Год назад

@@AustinOutdoors. thanks

@jaybirdtapsnracks3460 7 месяцев назад

This advice is incorrect. Loctite is a threadlocker and is made to be applied to the threads. A tiny bead or dot on the threads. Putting loctite on the tip can create a false pressure reading on the Torque wrench. As you tighten down the loctite can fill the void at the bottom and increases tension as it cannot be compressed. So you can have way less torque than you think.This is the worst way to apply loctite. @@tonymarinelli7304

@jaybirdtapsnracks3460 7 месяцев назад

Don't ever put Loctite on the tip. It is a threadlocker. Screws that come with reddots have pre-installed threadlocker on the threads. The tips are noticably and significantly absolutely clear of any Loctite.@@tonymarinelli7304

@ENIGMAtic1990 Год назад

Which t10 bit is that?

@phillipnaz9012 2 года назад

When I bought mine, someone at the gun shop said you should ONLY use the screws that came with it? I can’t recall if he said the screws that came with the slide, or the optic? I’m assuming it would have to be with the ones that came with the optic? Thanks guys!

@WorkmanFirearms 2 года назад

It would be the screws that came with the slide meant for that specific optic. - Aidan

@user-wo2rc3bf4x 7 месяцев назад

thanks for the info, but how would the slide manufacturer know what optic someone will use?

@jaybirdtapsnracks3460 7 месяцев назад

This looks like a custom slide, milled for the Holosun optic. So it comes with the correct screws and doesn't require a mounting plate. @@user-wo2rc3bf4x

@user-wo2rc3bf4x 7 месяцев назад

Apologize for earlier post. I just got a custom slide for my G20, and they specified that THEIR screws must be used with the chosen optic. It’s a Zaffiri, so I used their screws for my Holosun 507c. 15 inch pounds of torque with some blue loctite. So far it’s holding nicely. If I do my job and pull the trigger straight back I’m putting every round through the same hole 🕳️. Using a lone woof standard length barrel, oem internals, extractor, etc., and it runs. Had a few FTE, so I’m gonna try both the next higher & lower recoil springs (15 lb-20lb) and see if that effects the FTE.

@justkickinit6878 Год назад

Dude, where’s your adapter plate? That’s putting a lot of stress on those two little screws.

@MD-xb1qw Год назад

The plate is only needed for an RMR because the battery is exposed on the bottom unlike the enclosed battery on the Holosun.

@jaybirdtapsnracks3460 7 месяцев назад

This is a custom slide milled for a Holosun specifically, would also fit an RMR (same footprint) so no plates needed and it comes with the appropriate screws. Red dot brand specific adapter plates are needed for a Glock MOS, even the Holosun. @@MD-xb1qw

@martinover7927 25 дней назад

@@MD-xb1qwOn a “normal” Glock MOS slide, you do need a plate to install a Holosun 507C. This gun did not have that footprint, which should have been mentioned.