How To Install Heated Grips On A Triumph Speed Twin Motorcycle

Подписаться 32 тыс.

Просмотров 7 тыс.

50% 1

Here we show step by step instructions on installing OEM heated grips on a 2020 Triumph Speed Twin Motorcycle.
Triumph Heated Grips Part Number: A9638135 (see shop.triumphmotorcycles.com/h...)
Get 3ftDeep stuff: 3ftdeepsports.com/store
Filmed with a Canon 70D camera in the great Pacific Northwest.
Music: Spirit Of Fire, by Jesse Gallagher
0:00 Introduction
0:06 Heated Grips Installation (on a 2020 Triumph Speed Twin)
0:10 Remove the seat
0:18 Remove the fuel tank
0:31 Remove the tank hoses
0:34 fuel tank vent hose
0:41 Turn over engine to depressurize fuel system
0:48 Disconnect negative battery terminal
1:01 Disconnect electrical connectors
1:26 Remove bar end finishers and mirrors
1:59 Remove right twist grip
2:34 Route hand grip subharness
2:48 Connect left hand grip
3:14 this is the groove for the wires
3:19 Route right side of subharness
3:27 Refit switch housings
3:32 Torque to 2 Nm
3:48 Affix upper and lower switch housings
5:03 Check for throttle freeplay
5:08 Route remainder of subharness
5:23 Remove connector bracket
5:28 Remove lower connector from bracket
5:37 Remove blanking plug from connector
5:41 Remove clutch cable retaining bracket
5:58 Route harness through frame
6:04 Refit retaining bracket
6:10 blue indicator tape should be to right of retaining bracket
6:17 Torque screws to 3 Nm

Авто/Мото

Опубликовано:

26 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 26

@JelloThatsMellow Год назад

This kind of work is why I'm glad I worked the installation labor into part of the bike purchase deal. I'm sure they'd bill me 2 hours for this lmao.

@michaeljacquemond2864 Год назад

Very instructive! idea for a new video: valve clearance check 😁

@3ftDeepChannel Год назад

Thanks, Michael.

@petermiles6690 Год назад

I just wanted to say a big thank you for your video. Made my install very easy as I followed your instructions step by step. Thank you and ride safe buddy. All the best!

@3ftDeepChannel Год назад

You’re welcome, Peter. Thanks for the kind words.

@ivoruren3086 2 года назад

Hi here's an update. This video is great BUT only for 2019 2020 models. It took ages but I eventually found the dam three pin connector for the wiring loom on my 2021 upside down fork version. It is mounted on another plastic tray that is held in with one torx screw at the bottom of the headstock near the clutch cable. The connector is right in the front of the frame hidden away beside another white connector. So you don't need to remove that bracket with the other black connectors on just under the front of the tank. It is hidden aargh. I hope this helps for anyone doing this at home on the new model.

@3ftDeepChannel 2 года назад

Thanks very much for the information, Ivor. I'm sure it'll be helpful for others with newer models. Safe riding.

@ruudspark 2 года назад

Great video and also thanks Ivor, you may have saved me a world of pain!!

@ivoruren3086 2 года назад

@@ruudspark Haha, no problem it took me ages to find where Triumph have hidden the connector on the new model. But once I found it all was simple, the grips do work well and are plug and play. Just find it in that triangular area at the front of the frame, just above the bottom steering stem bearing in that triangular part. :-)

@jasonjetski Год назад

Thanks Ivor. I just used your comment to help me locate the connector on my 2023 scrambler 900. It is hidden quite well in there.

@danbeaman9376 11 месяцев назад

Thanks for posting this. It really is hidden on the new Speed Twins!

@SquireSCA Год назад

Good video, will be doing this soon myself. One note, you don't need to remove the tank. Just remove the rear bolt, and slide the tank back about 6 inches, and prop the front up with a block or roll of duct take. You can get to the wire harness from there quite easily.

@3ftDeepChannel Год назад

Thanks for the tip, Dave. We recognize there are shortcuts in getting some of these installations done, but we always go by the instruction manuals, to make sure people get the “fool-proof” method.

@SquireSCA Год назад

@@3ftDeepChannel Yeah, I figured as much. I hate taking the tank off, always worried about dropping it or breaking one of the plastic fittings on the fuel line... So just sliding it back and propping up the front, gave me plenty of room to unplug the O2 sensors when I tuned my 2022 Speed Twin, and those plugs are right next to the heated grip plug... Makes it a lot easier...

@donaldcox6090 2 года назад

Great Video, thank you 🙏 What’s the “special bit” (spec? size?) for the throttle housing removal / re-install? Thanks again

@3ftDeepChannel 2 года назад

The bit is a tri tip security bit the one that came with the spacer kit is marked S2 Y3.

@donaldcox6090 2 года назад

Your video was very helpful, and install went smoothly. I noticed you had installed the red throttle spacers. I bought my 2019 Speed Twin used, and the previous owner had already installed them. However, when I did the heated grip install, I noticed both spacers were broken. Any idea what would cause them to break? (Small end that interfaces with the throttle tube had snapped off both of them). Thx!

@3ftDeepChannel 2 года назад

That's odd I have not heard of any breaking.

@jasonjetski Год назад

Great video. Do you have a link where I could buy one of the special bits please?

@3ftDeepChannel Год назад

Thanks for the kind words. We’ve found a shortcut that doesn’t require use of the special bit on the 2019-20 models. If you loosen the wiring you can slide the grip to the end of the handlebar by only unscrewing the 2 Philips screws under the throttle assembly. You should then be able to remove the old throttle grip. Good luck and safe riding!

@LifeBehindBarsBigSky 11 месяцев назад

Do you think I could wire an optima usb connection to the wires on the hand grip heaters? How would I do it? Which wire on the 3 wire socket would I connect to?

@3ftDeepChannel 11 месяцев назад

What are you trying to do? Maybe there’s a better solution. If you’re just trying to install a USB charging plug, it’s best to run right off the battery with a fuse.

@YouKayTen 3 месяца назад

Woah! This is not for the faint hearted! You got to do all that for just heated grips!! 🙀 man how much does the dealer ship charge? P&L? PS: Thanks for the detailed video. It made me realise it maybe best to buy a used bike with heated grips already installed.

@3ftDeepChannel 3 месяца назад

Over here they charge $135 per hour. Parts are the same price. Glad we could help with your decision-making!

@YouKayTen 3 месяца назад

@@3ftDeepChannel wow yea what do you expect from a European dealership! As with anything, prices would be much higher here not cheaper even cause of exchange rates! its usually similar price in £££ plus 15-20-%!!!