Тёмный

How To Install LED Tail Light Bulbs on 2014-2018 Silverado Upgrade 

BadAssEngineering
Подписаться 6 тыс.
Просмотров 8 тыс.
50% 1

Installed LED bulbs in my Chevrolet Silverado 2015 Tail Lights. This also works on pretty much any Silverado from any year since the tail light design has not changed much.
Parts used in my particular application:
-Sylvania 7443 Red LED bulb replacements (2 pairs)
-50 w 6 Ohm resistors (4 units)
-Average MultiMeter to check for signals
-Soldering stuff
How to remove and replace tail light bulbs and replace them with LED units, along with resistors if used in case of turn signals. no hyperflash flash badassengineering
Chevrolet Silverado Suburban Tahoe Sierra GMC Yukon Cadillac GM Truck flash LED hyperflash hyper flash Universal tail light taillights brake lights 2014 2015 2016 2017 2018
1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 1998 1997 1996

Авто/Мото

Опубликовано:

 

12 янв 2021

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 18   
@fightclub1686
@fightclub1686 9 месяцев назад
I searched the entire internet and this was the most informative and helpful video on the subject. Thanks for posting!
@chandlermoore4649
@chandlermoore4649 5 месяцев назад
I am trying to do the same thing to my truck. Just to clarify, one end of the load resistor goes to the ground wire and the other end goes to the green wire? So crossing colors?
@bbenton1996
@bbenton1996 Год назад
My lights only needed one of these. I installed one on each side but only at the bottom bulb. Can’t hurt to try and do the bottoms only first
@kingboss50
@kingboss50 10 месяцев назад
Appreciate the video and letting me know the wires I needed to cut into and resistors to purchase
@joepanit
@joepanit 2 года назад
Resistors can get very hot. Zip ties won't melt?
@BadAssEngineering
@BadAssEngineering 2 года назад
It's been months and haven't had any problems, I don't use my turn signals too much tho
@wm3105
@wm3105 3 года назад
You should upgrade your upper control arms to some dirtkings, they make a big difference from stock
@BadAssEngineering
@BadAssEngineering 3 года назад
Already rocking a set of those ;) Review coming soon
@RC4X4
@RC4X4 Год назад
Hey. I just installed some premade resisitor wires for both bulbs on the right and left in the rear. The lights and brake lights work. The right turn signal works but the left still Hyper Flashes when the headlamps are on.. Any Idea? Do I have a faulty resistor.
@kingboss50
@kingboss50 9 месяцев назад
I would think not a good connection on the negative wires, I had same issue and made sure I had exposed wires on the negative to attach with the resistor
@mazamike
@mazamike Год назад
Was there a noticeable difference after installation?
@BadAssEngineering
@BadAssEngineering Год назад
Meaning amount of light ? Yes, very much, and since the On/Off is way sharper, it's safer so it commands better attention from other drivers
@mazamike
@mazamike Год назад
@@BadAssEngineering thank you 👍🏾
@nickwebber8404
@nickwebber8404 3 года назад
Did this not remove the turn signal?
@BadAssEngineering
@BadAssEngineering 3 года назад
Wut no
@nickwebber8404
@nickwebber8404 3 года назад
@@BadAssEngineering no worries. I'm doing a slightly different mod on my rear lights and the resistors didn't stop the BCM fault signal.
@BadAssEngineering
@BadAssEngineering 3 года назад
@@nickwebber8404 oh You ment the failed turn signal, with the resistors it got fixed
@nickwebber8404
@nickwebber8404 3 года назад
@@BadAssEngineering no. I'm trying to separate the turn signal away from the upper and lower bulbs to a designated turn only bulb. Fitted resistors to the circuit but its not right. I think I might know what the issue is.
Далее
Получилось у Миланы?😂
00:13
Просмотров 1,1 млн
Upgrade Your SILVERADO Reverse Lights In 3 Minutes!
2:58
профи на Тракторе Т-16
0:24
Просмотров 2,4 млн