How to install Pertronix Electronic Ignition

Подписаться 20 тыс.

Просмотров 70 тыс.

50% 1

In this video I cover how to upgrade from the standard points style ignition system to the Pertronix Electronic Ignition (part number 1281). This was incredibly easy to upgrade and can be done in no time. No longer needing to worry about adjusting the points is a piece of mind worth having with this system.
Ignition: Pertronix, part # 1281 amzn.to/3vfSGFQ
Also, check out the Pertronix 1.5 Ohm Coil to go with the Electronic Ignition amzn.to/3bpFgQV
Check out me new website for parts and merch that I am selling - krusebuilt.com/
Want to help support this channel, you can "buy me a coffee", check it out! www.buymeacoff...
The car is a 1966 Mustang Coupe with a factory V8 and 4 speed transmission.
This video is a How to change from a points ignition system to a point-less ignition system on a 1966 Mustang
Shot with GoPro Hero 5, edited on Davinci Resolve 16.
Credit for the music in the video:
::::::::::::::::::::
Epidemic Sound
Try it today! www.epidemicso...
::::::::::::::::::::
Instagram: / kruseview
Twitter: / kruseview

Опубликовано:

30 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 103

@sequoiaohz Год назад

Thanks good video. Two things to keep in mind for ignitor 1 model. The power supply should get 12v. Lay a new cable from the ignition swith or bridge the existing resistor cable. Most of the time only about 9 V arrive. This can lead to misfiring. And also important to mention is, if you screw on the car for example on the electrics. The ignition should not stay on too long without the engine running. This can destroy the Pertronix ignition module.

@AndyKruseChannel Год назад

Thanks for the heads up. :)

@onmywayup763 Год назад

yep. Also a higher power coil. like a Lucas DLB105. Only like $25. Old coil is made for a ballast setup. Running ign wire like OP said and bumping up coil should increase spark.

@BRUCE-y7l 6 месяцев назад

77 t bird ..does it need a different 12 volt wire / can t use existing wire?

@sequoiaohz 6 месяцев назад

@@BRUCE-y7l Messure if the positiv cable from ignition switch to the coil has 12V If not, there is a resistor installed. Then you have to find that cable near the ignition switch inside the car. Then bridge that cable, so there is the full voltage at the coil. You also can install a relay, so that the coil/ red wire from pertronix modul gets the full power from the battery

@JohnCox-b6k 10 месяцев назад

Good camera work best I’ve seen on installing the upgrade.

@AndyKruseChannel 10 месяцев назад

Thanks!

@davidrandall9964 Год назад

When removing points screws, don’t drop them so they end up down inside your distributor like I did. 40 mins later with a tiny magnetic screwdriver I found them and managed to get them out.

@AndyKruseChannel Год назад

This is good advice. :)

@andrebrooks7040 Месяц назад

Would this cause a rattle when you rev it? I have a 1974 Ford with a 360 in it. Sounds crisp but certain times when you rev it, sounds like a tiny screw is rattling somewhere. Previous owner converted the system.

@WayneGregoryGMCS Месяц назад

Just here to say that you video was well done.

@AndyKruseChannel Месяц назад

Thanks!

@fredmetcalf 26 дней назад

EXCELLENT....very well done.....everything about it.....very helpful

@AndyKruseChannel 25 дней назад

Glad it was helpful!

@Mahindajayamaha64 Месяц назад

Any palatinum distibuter can fix this part. Specially my van c22 vanette.

@AndyKruseChannel Месяц назад

Thanks for the heads up. 🙂

@superpapi Год назад

Ohhh! I always wanted this for my old Mustang. I'll be upgrading this in my next project Mustang for sure!

@AndyKruseChannel Год назад

Definitely a must have on these old cars.

@angry3055 Месяц назад

The issue I had the magnetic sleeve fit a loose on the lobes may be due to being a rebuild unit? I used telflon,too help it fit snuggly over it, and then it will hold tight with the rotor on it. Do not freak out if it's not perfectly rounded, mine was off set by .006 on one side it still works. They are not sensitive like a computer control module.

@AndyKruseChannel Месяц назад

Yeah, haven't had any issues with the four of these units I have now installed over various vehicles. :)

@angry3055 Месяц назад

@AndyKruseChannel the issue was not the Pertronix kit, but the distributor reluctor sleeve that goes over the distributor cam,my distributor was a remanfacture unit and was regrounded leaving excessive clearance for the sleeve. I used telfon tape to make up the loose gap and do not use metallic tapes or glue type chemicals.

@thirdcargarage2951 Год назад

Make sure you have 12 volts to the Petronix. Not the 9 volts from a resistor.

@AndyKruseChannel Год назад

Good to know.

@SpaceNazi62 Месяц назад

Was it really that easy? Bought my grandson a 73 Maverick Grabber and want to do away with the points.

@AndyKruseChannel Месяц назад

It's as easy as I describe in the video. I have now done this on four different vehicles and it has worked right out of the box every time. It will likely be faster for you than it was for me since you don't have to setup the camera and check the mirror to make sure you look pretty. :)

@SpaceNazi62 8 дней назад

My distributor is a little different. There’s a red wire coming from the coil already into a harness that’s goes into the firewall.

@SpaceNazi62 8 дней назад

Who hoo we got the maverick started. Really was easy. Thanks.

@BIGBADWOOD 2 года назад

5 stars ---- THANKS !

@AndyKruseChannel 2 года назад

Awesome, hopefully there was some good info in there for you. :)

@BRUCE-y7l 6 месяцев назад

good vid music is annoying and disrtacting

@AndyKruseChannel 6 месяцев назад

Cool, this video is over 3 years old, what would you like me to do?

@mlungisimabele8679 3 года назад

This is so great need to get one for my nissan l18

@AndyKruseChannel 3 года назад

Definitely worth the money!

@patrickjoseph-q4k 6 месяцев назад

Nissan Micra 2001-2002 CGA3DE has elctronic ignition?. 1li - CG10DE

@AndyKruseChannel 6 месяцев назад

Thanks for the heads up.

@bdrosity6673 8 месяцев назад

Question, I did a motor swap on my 1976 Ford F-150. I took my 76’ 302 out and replaced it with a 95’ 302. We’re having trouble with the distributor. The 95’ is electronic where the 76’ was a points system. We tried to used the 76’ distributor with the 95’ motor but it seems that they’re not the same length or the oil pump rods are different lengths. The ignition plugs are not the same either. Not to sure what to do. Any advice?

@AndyKruseChannel 8 месяцев назад

Unfortunately I don't have much experience with the late model 302s, so I don't think I'm going to be much help here.

@amphibiousone7972 8 месяцев назад

Was your coil internally ballast? I didn't see a ballast resistor any where. Asking for a friend. 🤣 Good video. But seriously, do i need to keep or loose my ballast resistor?

@AndyKruseChannel 8 месяцев назад

I have the ‘pink’ resistor wire behind my gauge cluster, so I have an external resistor system.

@steveconnolly7129 7 месяцев назад

The dura spark2 on my 67 works just fine,very easy to adj.from 6° to 22°perfomence goes out the window,and speed is fast,just plain fast

@AndyKruseChannel 7 месяцев назад

Good to know. :)

@scottschmittmusic 4 месяца назад

Is the black wire negative? I just don't want to screw it up

@AndyKruseChannel 4 месяца назад

Yes.

@williambuchanan8204 3 месяца назад

Great video mate! Will this product work on 4cyl motors too?

@AndyKruseChannel 3 месяца назад

I don't know why it wouldn't, just need to get the correct version from Pertronix and you're set! :)

@monsterblue7453 Год назад

Let me know how long the petronix ignitions last? I installed one in my mustang a few years back, do I need to buy a back up unit or do you feel they will last years??

@AndyKruseChannel Год назад

I've installed one in each of my Mustangs, never had an issue with them. :)

@CarlosSilva-bl1ch Год назад

Nice vid'.......thx for sharing. I am thinking of installing a Pertronix Ignitor in my '66 Fury. I was wondering if you had to turn your distributor to adjust the timing of your Mustang after you did this video?

@AndyKruseChannel Год назад

Thanks! No adjustment to the timing is needed, but it's also assuming your timing is already dialed in before the upgrade. If not, no big deal, install the Pertronix, and then you can go about setting the timing just as if you had the old points in the car. I have a video on that if you need to watch it for a refresh. :)

@RayL-i5i 2 месяца назад

Nice clean video. Looks to be a nice product.I would at a minimum check ignition timing after. But thats just me...

@AndyKruseChannel 2 месяца назад

Thanks, but considering the distributor is not moved or adjusted for this upgrade, the timing will be exactly where it was before the upgrade began. 🙂

@rayl9335 2 месяца назад

yes I understand that but assuming the physical placement of module will sync with points dwell setting is a bit too iffy since dwell can affect ignition timing. It's just me wanting to be 100%.

@dtruth5769 2 года назад

My 289 had a dual point distributor. Would this item still work? Thanks for vid

@AndyKruseChannel 2 года назад

It should, just remove both points and the condenser, install the hall-effect sensor and slide on the magnetic ring. Good luck!! :)

@hughphillips67Mustang Год назад

So, my factory coil on my 67 289 has a red and black wire. The yellow top on the coil is marked positive and negative. My new coil is marked battery and distributor. Which wire goes to which terminal? I don't want to burn up a new coil

@AndyKruseChannel Год назад

It should be the same, red to positive and black to negative. But I am confused why the new coil is marked battery and distributor, I have not seen that before.

@hughphillips67Mustang Год назад

@@AndyKruseChannel that's because your last name isn't Phillips. You don't have my luck. Lol. I would send a picture to you if I could

@josevilla7442 2 года назад

Would this work on a 260 v8 mercruiser boat motor

@AndyKruseChannel 2 года назад

Yes, but I believe you'll want the ML-181 part number. The specific unit I used in this video won't work, but that new part number should. :)

@Cheepauctioncars 2 года назад

Good afternoon brother Do you know if it is the same for a 350 small block

@AndyKruseChannel 2 года назад

I believe you want the Pertronix 1181 for the SBC, not the 1281 that I use on my 289. Other than that, everything else should be the same. :)

@jatalberg 3 года назад

I'm picking one up tomorrow Andy, saw one dude install........... after he was adjusting timing and such. There was no need right, just getting rid of points right, you never time a car after adjusting points so I see no reason after installing this?

@AndyKruseChannel 3 года назад

I have not touched or changed anything with respect to my timing since I made that video. On a previous Mustang I had problems with the points to where I had to have the car towed one time. I installed this Petronix system on that car and never had problems again. It was one of the first items I new I wanted to buy for this Mustang because I knew it worked so well. It really is a "set it and forget it" part. It doesn't matter if it's winter or summer, it always works. :)

@jatalberg 3 года назад

Thanks I’m sticking with just that, I’m not getting a hotter coil, I read too many positive/negative talk on coils, I’ll stick with stock coil. One guy on here did same install you did but he had a coil that had one terminal and he was pulling wires through firewall splicing, I’m like damn stick with stock coil unless they have one slightly better than stock without being too hot. Less than 40,000

@Resq28 2 года назад

Hello, thx for posting this. I need to readjust my module inside the distributor but don’t have the plastic tool. Do you know what gap that is? Thank you.

@AndyKruseChannel 2 года назад

Pertronix says that gap needs to be 0.030"

@Resq28 2 года назад

@@AndyKruseChannel Thank you so much Andy!

@tenchfries2124 4 месяца назад

Exactly what i needed to see!

@AndyKruseChannel 4 месяца назад

Awesome, glad I could help. :)

@builderjoe4870 11 месяцев назад

Thanks, good video!

@AndyKruseChannel 11 месяцев назад

Glad it helped!

@warhawkgarage1272 3 года назад

Did you remove your resist wire? I have read these years need that removed to get the full 12 volts to coil.

@AndyKruseChannel 3 года назад

Sorry Boss, I'm not sure I understand which wire you are referring to. Inside the Cap, there is the Capacitor and the Points mechanism which I removed. The only thing I left in there was the ground wire from before.

@warhawkgarage1272 3 года назад

@@AndyKruseChannel the way I understand it is, the hot to the coil is only 12 volts at cranking. The rest of the time its 7-9 volts because of the resist wire. But honestly I don't know where the resist wire is thats why I'm wanting videos so I can get it right and not mess my pertonix unit. But your video is 7 months old guess if it wasn't working you would know by now so guess your right my info must be wrong. Thanks for videos I appreciate them.

@AndyKruseChannel 3 года назад

@@warhawkgarage1272 I had this Petronix system in my previous '66 Mustang, and now in this '66 Mustang. I'd agree, if there was any ignition issues I would have had them by now. :) I'm glad you are able to find some value in these videos.

@warhawkgarage1272 3 года назад

@@AndyKruseChannel great videos keep them up.

@tripledoublemedia9119 2 года назад

Sup Warhawk and Andy, yes there is a pink resistor wire on my 65' mustang coupe. It's purpose is to prevent the coil from receiving a full 12 volts when the key is in the "on" position. This was used on early model Mustangs and even comes in the new wiring harnesses. Pertronix says that the ignitor needs the full 12 volts though and anything less will damage the module. So you need to either bypass the resistor wire, remove it (wouldn't recommend that in case you need to go back to points for some reason), or you can buy the relay that Pertronix sells for this issue exactly. If none of that made sense, please refer to these links for more info :) 1) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-uQ0smsIO8Js.html 2) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-c76knXFuXH0.html 3) www.vintage-mustang.com/threads/pertronix-resistor-wire.1159894/ 5) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-D2X-m1uRYLw.html 4) www.cjponyparts.com/pertronix-ignition-power-relay-kit/p/PER2001

@fuzzcouchmania5122 7 месяцев назад

Ace the Annoying music.

@AndyKruseChannel 7 месяцев назад

I've never had someone call my Ace here on RU-vid, but I'll take it. :)

@robnordyke6151 3 года назад

Thank you for posting the walk through. It makes perfect sense... but the inside of my distributor cap has an additional plate and springs. It seems like it should come out. Suggestions? I don't think I can post a pic here.

@AndyKruseChannel 3 года назад

Good question, you could email me the pic, my email contact is in the "About" section on my channel.

@robnordyke6151 3 года назад

@@AndyKruseChannel thanks man. You are a Saint. I have this taken apart and am now stuck. Sending!

@AndyKruseChannel 3 года назад

@@robnordyke6151 Got the pic, I replied, the short answer looks like it should still work. :)

@bobbyvihaan9002 3 года назад

you probably dont give a shit but does any of you know a method to get back into an instagram account?? I was stupid forgot my password. I appreciate any tricks you can offer me.